Black Box ServSwitch Manual de usuario

THE SERVSWITCH™FAMILY

Welcome to the ServSwitchTM Family!

Thank you for purchasing a BLACK BOX®ServSwitch™Brand video switch! We

appreciate your business, and we think you’ll appreciate the many ways that your

new video switch will save you money, time, and effort.

Our ServSwitch family is all about breaking away from the traditional, expensive

model of computer management and display. You know, the one-size-fits-all-even-if-

it-doesn’t model that says, “One dedicated computer gets one dedicated monitor

or user station, no more, no less.” Why not a single user station (monitor,

keyboard, and mouse) for multiple computers—even computers of different

platforms? Why not a pair of user stations, each of which can control multiple

computers? Why not many monitors or user stations for the same computer?

Why not display or access any of your computers, anywhere in the world, with

any of your monitors or user stations?

With our ServSwitch products, there’s no reason why not. We carry a broad line

of robust solutions for all these applications.

• Do you have just two PCs, and need an economical alternative to keeping two

monitors, keyboards, and mice on your desk? Or do you need to share dozens

of computers, including a mix of IBM®PC, RS/6000®, Apple®Macintosh®, Sun

Microsystems®, and SGI®compatibles among multiple users with different

access levels?

•

Do you have to send video from one computer to two different local monitors?

Or do you

need to send video from multiple computers to dozens of monitors

both near and far?

• Does your switch have to sit solidly on a worktable and use regular everyday

cables? Or

does it have to be mounted in an equipment rack and use

convenient many-to-one cables?

No matter how large or small your setup is, no matter how simple or how

complex, we’re confident we have a ServSwitch system that’s just right for you.

The ServSwitch™family from Black Box—the one-stop answer for all your

KVM-switching needs!

This manual will tell you all about your new ServSwitch™ Brand Matrix Video

Switch, including how to install, operate, and troubleshoot it. For an introduction

to the Switch, see Chapter 2. The Matrix Video Switch product code covered in this

manual is:

ACL0404A

SERVSWITCH™BRAND MATRIX VIDEO SWITCH

TRADEMARKS USED IN THIS MANUAL

BLACK BOX and the logo are registered trademarks, and ServSwitch

is a trademark, of Black Box Corporation.

Apple and Macintosh are registered trademarks of Apple Computer, Inc.

IBM is a registered trademark of IBM Corporation.

SGI is a registered trademark of Silicon Graphics, Inc.

Sun and Sun Microsystems are registered trademarks of Sun Microsystems, Inc.

in the United States and other countries.

Any other trademarks mentioned in this manual are acknowledged to be the property

of the trademark owners.

FCC/IC STATEMENTS, EU DECLARATION OF CONFORMITY

FEDERAL COMMUNICATIONS COMMISSION

AND INDUSTRY CANADA

RADIO-FREQUENCY INTERFERENCE STATEMENTS

This equipment generates, uses, and can radiate radio-frequency energy and if not

installed and used properly, that is, in strict accordance with the manufacturer’s

instructions, may cause interference to radio communication. It has been tested

and found to comply with the limits for a Class A computing device in accordance

with the specifications in Subpart J of Part 15 of FCC rules, which are designed to

provide reasonable protection against such interference when the equipment is

operated in a commercial environment. Operation of this equipment in a

residential area is likely to cause interference, in which case the user at his own

expense will be required to take whatever measures may be necessary to correct

the interference.

Changes or modifications not expressly approved by the party responsible

for compliance could void the user’s authority to operate the equipment.

This digital apparatus does not exceed the Class A limits for radio noise emission from

digital apparatus set out in the Radio Interference Regulation of Industry Canada.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites

applicables aux appareils numériques de la classe A prescrites dans le Règlement sur le

brouillage radioélectrique publié par Industrie Canada.

EUROPEAN UNION DECLARATION OF CONFORMITY

This equipment complies with the requirements of the European EMC directive

89/336/EEC.

SERVSWITCH™BRAND MATRIX VIDEO SWITCH

NORMAS OFICIALES MEXICANAS (NOM)

ELECTRICAL-SAFETY STATEMENT

INSTRUCCIONES DE SEGURIDAD

1. Todas las instrucciones de seguridad y operación deberán ser leídas antes

de que el aparato eléctrico sea operado.

2. Las instrucciones de seguridad y operación deberán ser guardadas para

referencia futura.

3. Todas las advertencias en el aparato eléctrico y en sus instrucciones de

operación deben ser respetadas.

4. Todas las instrucciones de operación y uso deben ser seguidas.

5. El aparato eléctrico no deberá ser usado cerca del agua—por ejemplo, cerca

de la tina de baño, lavabo, sótano mojado o cerca de una alberca, etc.

6. El aparato eléctrico debe ser usado únicamente con carritos o pedestales que

sean recomendados por el fabricante.

7. El aparato eléctrico debe ser montado a la pared o al techo sólo como sea

recomendado por el fabricante.

8. Servicio—El usuario no debe intentar dar servicio al equipo eléctrico más allá

a lo descrito en las instrucciones de operación. Todo otro servicio deberá ser

referido a personal de servicio calificado.

9. El aparato eléctrico debe ser situado de tal manera que su posición no

interfiera su uso. La colocación del aparato eléctrico sobre una cama, sofá,

alfombra o superficie similar puede bloquea la ventilación, no se debe colocar

en libreros o gabinetes que impidan el flujo de aire por los orificios de

ventilación.

10. El equipo eléctrico deber ser situado fuera del alcance de fuentes de calor

como radiadores, registros de calor, estufas u otros aparatos (incluyendo

amplificadores) que producen calor.

11. El aparato eléctrico deberá ser connectado a una fuente de poder sólo del

tipo descrito en el instructivo de operación, o como se indique en el aparato.

NOM STATEMENT

12. Precaución debe ser tomada de tal manera que la tierra fisica y la polarización

del equipo no sea eliminada.

13. Los cables de la fuente de poder deben ser guiados de tal manera que no

sean pisados ni pellizcados por objetos colocados sobre o contra ellos,

poniendo particular atención a los contactos y receptáculos donde salen del

aparato.

14. El equipo eléctrico debe ser limpiado únicamente de acuerdo a las

recomendaciones del fabricante.

15. En caso de existir, una antena externa deberá ser localizada lejos de las lineas

de energia.

16. El cable de corriente deberá ser desconectado del cuando el equipo no sea

usado por un largo periodo de tiempo.

17. Cuidado debe ser tomado de tal manera que objectos liquidos no sean

derramados sobre la cubierta u orificios de ventilación.

18. Servicio por personal calificado deberá ser provisto cuando:

A: El cable de poder o el contacto ha sido dañado; u

B: Objectos han caído o líquido ha sido derramado dentro del aparato; o

C: El aparato ha sido expuesto a la lluvia; o

D: El aparato parece no operar normalmente o muestra un cambio en su

desempeño; o

E: El aparato ha sido tirado o su cubierta ha sido dañada.

SERVSWITCH™BRAND MATRIX VIDEO SWITCH

Contents

Chapter Page

1. Specifications ............................................................................................. 7

2. Introduction ............................................................................................... 9

3. Installation ................................................................................................ 10

4. Operation ................................................................................................. 12

4.1 The Switch’s LEDs ............................................................................ 12

4.2 Switching Manually With the Keypad .............................................. 13

4.3 Switching With (or Through) a Serial Device .................................. 14

5. Troubleshooting ...................................................................................... 15

5.1 Calling Black Box .............................................................................. 15

5.2 Shipping and Packaging ................................................................... 15

Appendix - Advanced Features *** Scan Mode *** .................... 16

CHAPTER 1: Specifications

1. Specifications

Compliance — CE; FCC Part 15 Subpart J Class A, IC Class/classe A

Standards — VGA, SVGA, XGA, or XGA-2 video

Interfaces — Video: VGA;

Serial: EIA/TIA RS-232, pinned according to TIA-574,

DTE

Supported

Video Types — RGBHV (VGA, SVGA, XGA, or XGA-2), RGBS, or

RGsB (“sync on green”)

Resolution and

Refresh Rate — Up to 1600 x 1280 noninterlaced at up to 85 Hz

Video Coupling — DC

Video Level — 0.7 volts peak-to-peak

Video Gain — 1-to-1 (buffered)

Supported Serial

Characteristics — Transmission protocol: Asynchronous;

Data rate: 1200 bps, fixed;

Data format: 8 data bits; no parity; and 1 or more stop

bits (fixed)

Maximum

Distance — Up to 150 ft. (45.7 m) of total cable length from attached

CPU/input device to attached monitor/output device

User Controls — (1) Front-mounted rocker switch for power;

Switching commands (ASCII “make” and “break” codes

from PC or included serial keypad)

Indicators — (16) Front-mounted LEDs to show video connections

SERVSWITCH™BRAND MATRIX VIDEO SWITCH

Connectors — On Switch itself:

(8) HD15 female for video: (4) to CPUs’ video ports

(or other sources), (4) to monitors (or other

destinations);

(1) DB9 male for serial;

(1) 5-pin DIN female for power;

On power-supply transformer:

(1) IEC male inlet for power

Maximum

Altitude — 10,000 ft. (3048 m)

Temperature

Tolerance — Operating: 32 to 122˚F (0 to 50˚C);

Storage: –40 to +185˚F (–40 to +85˚C)

Humidity

Tolerance — Up to 95% noncondensing

Enclosure — Steel

MTBF — 300,000 hours (calculated estimate)

Power — From utility-power (mains) outlet, through included

detachable output cord and external universal power

supply:

Input: 100 to 250 VAC at 50 to 60 Hz (autosensing);

Output: +5 VDC at 1 A, +12 VDC at 0.5 A, and –12 VDC

at 0.5 A;

Consumption: 5 VA (5 watts) maximum

Size — 2.3"H x 8.3"W x 5.3"D (5.9 x 21.1 x 13.5 cm)

Weight — Net:

Switch itself: 2.2 lb. (1 kg);

Keypad: 1 lb. (0.5 kg);

Power supply: 3 lb. (1.4 kg);

Shipping: 7 lb. (3.2 kg)

CHAPTER 2: Introduction

2. Introduction

The ServSwitch™Brand Matrix Video Switch is an ideal tool for sharing and/or

switching between the output of as many as four video sources (such as PCs), in

order to display or capture that output at up to four video destinations (such as

monitors).Once you attach all your devices, you can hook the Switch to the

included keypad for manual control, or to a PC for software-controlled sensing

and switching.

The Switch’s features include:

• With its large bandwidth, it can handle even very high resolutions and refresh

rates, up to 1600 x 1280 pixels at up to 85 Hz.

• It includes a serial keypad, so it’s ready to do manual switching almost right

out of the box (you do have to attach the keypad to the Switch first).

• Because it has a universal power supply, you can plug it in almost anywhere if

you have the right input cord. (And it is small and light enough to take almost

anywhere!)

• It’s primarily designed to carry VGA/SVGA video, but it can handle separate

horizontal and vertical sync, composite sync, and sync on green, so with the

right kinds of cables or adapters it can accept all sorts of video from all sorts

of devices.

• All of its input and output signals are buffered, so you’ll get the sharpest

possible images.

• It can drive video signals as far as 150 ft. (45 m) end-to-end, so it’s ideal for use

in auditoriums, conference halls, and similar spaces.

• You can use it in many types of remote or automated systems, because it can be

controlled from most RS-232 source devices.

• Each of its outputs can be blanked, so you don’t have to worry about people

seeing things you don’t want them to.

• Its front-panel LEDs show you right away which video inputs are going to

which outputs.

• To top it off, it can be operated by pressing a couple of buttons, so anybody

can use it without having to be extensively trained.

SERVSWITCH™BRAND MATRIX VIDEO SWITCH

3. Installation

To set up your ServSwitch™Brand Matrix Video Switch system, take these steps:

1. Making sure that the Switch is powered off, find its input ports. (These are

the top row of HD15 connectors on its rear panel, shown in Figure 3-1,

labeled “CPU 1” through “CPU 4”.) Run cabling from these ports to the

video-output ports of the PC CPUs or other devices that will be providing the

Switch’s video input.

If all of these input devices are transmitting VGA/SVGA/XGA-type

video signals on HD15 female connectors, you can use standard VGA video-

extension cables such as our product code EVNPS05-MM. Keep in mind that

the length of any of these cables plus the length of any of your monitor/

output cables (see step 2) should not be more more than 150 ft. (45 m).

If any of your input devices transmit some other type of video signal

and/or use some other type of video connector, you might need special

cables or adapters; call Black Box Technical Support.

Figure 3-1. The Switch’s rear-panel connectors.

2. The Switch’s output ports are the bottom row of HD15 female connectors

labeled with numbered monitor icons. If all of your output devices are

standard VGA or multisync monitors with HD15 male connectors on their

video cables, you can plug them directly into these ports (if they’ll be placed

nearby) or run video-extension cables to them such as our product code

EVNPS05-MF (if they’ll be some distance away). Keep in mind that the length

of any of these cables plus the length of any of your CPU/input cables (see

step 1) should not be more more than 150 ft. (45 m).

If any of your output devices are designed to receive a non-VGA video

signal and/or use a different type of video connector, you might need special

cables or adapters; call Black Box Technical Support.

Otros manuales para ServSwitch

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cambiar de Black Box

Black Box

Black Box LGB5052A-R3 Manual de usuario

Black Box

Black Box ServSwitch Octopus KV1701E Manual de usuario

Black Box

Black Box SS1P-SH-DVI-UCAC Manual de usuario

Black Box

Black Box SERVSWITCH Series Manual de usuario

Black Box

Black Box ServSwitch KV5004MN-R2 Manual de usuario

Black Box

Black Box SW1000A Manual de usuario

Black Box

Black Box AVSW-VGA8X8-B Manual de usuario

Black Box

Black Box Express Entry LB9005A-FO-R2 Manual de usuario

Black Box

Black Box KV1044A-R2 Manual de usuario

Black Box

Black Box LPB316A Manual de usuario

Black Box

Black Box SW1007A Manual de usuario

Black Box

Black Box LGB304A Manual de usuario

Black Box

Black Box SM906C Manual de usuario

Black Box

Black Box ServSwitch KV104A-R3 Manual de usuario

Black Box

Black Box PSE518SA Manual de usuario

Black Box

Black Box SWL930A-R2 Manual de usuario

Black Box

Black Box IC562A Manual de usuario

Black Box

Black Box SW1005A Manual de usuario

Black Box

Black Box Active Star Hub IC207A Manual de usuario

Black Box

Black Box 12 VDC load Manual de usuario

Black Box

Black Box ServSwitch Secure Plus (with USB) Manual de usuario

Black Box

Black Box LBG1000A Manual de usuario

Black Box

Black Box LP004A Manual de usuario

Black Box

Black Box IC248A Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario