Black Box LB9032A Manual de usuario

Installation

This installation guide gives step-by-step instructions about how to install the LB9032Aswitch:

Selecting a Site for the LB9032ASwitch

As with any electric device, you should place the switch where it will not be subjected to extreme temperatures, humidity,

or electromagnetic interference. Specifically, the site you select should meet the following requirements:

-The ambient temperature should be between 32 and 104 degrees Fahrenheit (0 to 40 degrees Celsius).

-The relative humidity should be less than 90 percent, non-condensing.

-Surrounding electrical devices should not exceed the electromagnetic field (RFC) standards for IEC

801-3, Level 2 (3V/M) field strength.

-Make sure that the switch receives adequate ventilation. Do not block the ventilation holes on each side of

the switch or the fan exhaust port on the rear of the switch.

-The power outlet should be within 1.8 meters of the switch.

Connecting to Power

Internal power (eight 10/100 RJ-45 ports or seven 10/100 RJ-45 ports plus one fiber port):

Step 1: Connect the supplied AC power cord to the receptacle on the back of the switch, and then plug it into a standard AC outlet with a

voltage range from 100 to 260 Vac.

Step 2:Turn on the switch by flipping the ON/OFF switch on the rear of the unit to I (ON) position.

Step 3:The Oposition is OFF.

Figure 1: Rear view

External power (seven 10/100 RJ-45 ports plus one fiber port):

Step 1: Connect the supplied AC to DC power adapter to the receptacle at the back of the switch.

Step 2:Attach the plug into a standard AC outlet with the appropriate AC voltage.

Figure 2: Rear view

CUSTOMER Order toll-free in the U.S. 24 hours, 7 A.M. Monday to midnight Friday: 877-877-BBOX

SUPPORT FREE technical support, 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746

INFORMATION Mail order: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018

Web Site: www.blackbox.com ?E-mail: [email protected]

Connecting to Your Network

Cable Type & Length

It is necessary to follow the cable specifications below when connecting the switch to your network. Use

appropriate cables that meet your speed and cabling requirements.

Table 3: Cable Specifications

Speed Connector Port

Speed

Half/Full

Duplex

Cable Max.

Distance

10BASE-TRJ-45 10/20

Mbps 2-pair UTP/STP

Cat. 3, 4, 5 100 m

100BASE-TX RJ-45 100/200

Mbps 2-pair UTP/STP

Cat. 5 100 m

100BASE-FX ST, SC, MT-RJ,

VF-45 100/200

Mbps MMF (50 or

62.5µm) 2 km

100BASE-FX SC 100/200

Mbps SMF (9 or

10µm) 15, 40, or

75 km

Cabling

Step 1: First, ensure the power of the switch and end devices is turned off.

<Note> Always ensure that the power is off before any installation.

Step 2:Prepare cable with corresponding connectors for each type of port in use.

<Note> To connect two regular RJ-45 ports between switches or hubs, you need a cross-over cable.

Step 3:Consult Cable Specifications Table on previous page for cabling requirements based on connectors and speed.

Step 4:Connect one end of the cable to the switch and the other end to a desired device.

Step 5:Once the connections between two end devices are made successfully, turn on the power and the switch is operational.

CUSTOMER Order toll-free in the U.S. 24 hours, 7 A.M. Monday to midnight Friday: 877-877-BBOX

SUPPORT FREE technical support, 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746

INFORMATION Mail order: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018

Web Site: www.blackbox.com ?E-mail: [email protected]

Tabla de contenidos

Otros manuales de Cambiar de Black Box

Black Box

Black Box KVT8DVIU Manual de usuario

Black Box

Black Box IC159A Manual de usuario

Black Box

Black Box ServSwitch Duo IP ACR6208A Manual de usuario

Black Box

Black Box LPB201A Manual de usuario

Black Box

Black Box KV1424A-R2 Manual de usuario

Black Box

Black Box LPB2810A Manual de usuario

Black Box

Black Box SERVSWITCH PANTHER KV1108A Manual de usuario

Black Box

Black Box LGB1048A Manual de usuario

Black Box

Black Box ServSwitch Diagrama de cableado

Black Box

Black Box KV120A Manual de usuario

Black Box

Black Box ServSwitch Plus Series Manual de usuario

Black Box

Black Box LGB1108A Manual de usuario

Black Box

Black Box AVSW-VGA4X1A Manual de usuario

Black Box

Black Box LB9006A-SC Manual de usuario

Black Box

Black Box LGB5052A-R3 Manual de usuario

Black Box

Black Box ServSwitch Ultra KV5002MA-R2 Manual de usuario

Black Box

Black Box KV6224DPH Manual de usuario

Black Box

Black Box AC1032A-2A Manual de usuario

Black Box

Black Box LGB616A Manual de usuario

Black Box

Black Box ServSwitch KV0004A Manual de usuario

Black Box

Black Box SW1005A Manual de usuario

Black Box

Black Box LGB1108A Manual de usuario

Black Box

Black Box LB9902A Manual de usuario

Black Box

Black Box ServSwitch Wizard SW641A Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario