BIXOLON XD Series Instrucciones de instalación

1. Turn the Power Switch Off at the rear of the Printer.

2. Remove the Cover Roller L&R and press the right side of the Cover STD

in the direction indicated by the yellow arrow to remove it.

※You can also remove it by pressing the left side in the same manner.

3. Insert the Auto Cutter Wire and Auto Cutter GND wire into the Wire Hole.

4. Engage the Hooks (red circles) with the square-shaped sockets

(yellow squares) in the order from top to bottom.

※Be careful that the Wire does not get stuck.

5. Reassemble the Cover Roller L&R that was removed in step 2.

6. Place the bottom of the Printer face the front. Press the Hooks (red circles)

toward the inner side to remove the Cover DIP. Then, shape the Auto Cutter

Wire and Auto Cutter GND Wire as shown below.

※Be careful to avoid tangling with other wires when shaping.

7. Insert the Auto Cutter Wire and Auto Cutter GND Wire into the Auto Cutter

Connector and Auto Cutter GND Connector (red square) in the correct direction.

8. Reassemble the Cover DIP that was removed in step 6.

9. In order to operate the Auto Cutter, the settings must be changed through the utility.

Access the Bixolon webpage (www.bixolon.com) and download the Unified Label

Utility.

Connect the communication cable (USB) and Turn the Printer power On.

Then, change the settings in the following order.

How to Mount Auto Cutter

KN04-00217A (Ver.1.0)

XD/XQ(4inch Model) Series

①Launch ‘Unified Label Utility’

②‘USB’ Click!

③‘Connect’ Click!

④‘OK’ Click!

⑤‘Configure Printer Setting’ Click!

⑥‘Advanced’Click!

⑦‘Get From Printer’ Click!

⑧Media Handling ‘Cutter’ Setting!

⑨‘Set to Printer’ Click!

⑩‘Close’ Click!

①

②

③

⑤

⑥

⑧

⑦

⑨

⑩

④

Off

Power Switch

Cover STD

Cover Roller L&R

Auto Cutter Wire

Auto Cutter GND Wire

Wire Hole

Cover DIP

Auto Cutter Wire

Auto Cutter GND Wire

Peeler Connector

Auto Cutter Connector

Auto Cutter GND Connector

Cover DIP

1. Printer 후면의 Power Switch 를Off 하십시오.

2. Cover Roller L&R 을분리 후, Cover STD 의우측을 내측 방향(노란색 화살표)으로

눌러 분리하십시오.

※같은 방법으로 좌측을 눌러 분리해도 무관 합니다.

3. Auto Cutter Wire 와Auto Cutter GND Wire 를Wire Hole 에삽입하십시오.

4. 빨간색 원표시 부의 Hook 를노란색 사각형 홈에 맞추어 상측에서 하측으로

조립하십시오.

※조립 시Wire 가끼이지 않도록 주의하십시오.

5. 순서 2 에서 분리한 Cover Roller L&R 을재조립하십시오.

6. Printer 바닥 면이 정면으로 향하게 하십시오. Hook(빨간색 원)를내측 방향으로

눌러 Cover DIP 을분리하고, Auto Cutter Wire 와Auto Cutter GND Wire 를하기

그림과 같이 보이게 정형하십시오. ※다른 Wire 와꼬이지 않게 정형 하십시오.

7. Auto Cutter Wire 와Auto Cutter GND Wire 를방향에 맞추어 Auto Cutter

Connector 와Auto Cutter GND Connector(빨간색 사각형)에삽입하십시오.

8. 순서 6 에서 분리한 Cover DIP 을재조립하십시오.

9. Auto Cutter 를작동시키기 위해서는 유틸리티를 통해 설정 값을 변경해야 합니다.

빅솔론 홈페이지(www.bixolon.com)에접속하여 라벨 통합 유틸리티를 다운 받은

후, 통신 케이블(USB) 연결 및Printer 의전원을켠다음 하기 순서대로 설정을

변경해 주십시오.

Auto Cutter 장착 방법

KN04-00217A (Ver.1.0)

XD/XQ(4inch Model) 시리즈

①

⑥

⑧

⑦

⑨

⑩

⑤

②

③

④

①‘Unified Label Utility’실행

②‘USB’클릭!

③‘연결’ 클릭!

④‘확인’ 클릭!

⑤‘프린터 환경 설정’ 클릭!

⑥‘고급설정’ 클릭!

⑦‘프린터 설정값 가져오기’ 클릭!

⑧매체 핸들링 ‘커터’ 셋팅!

⑨‘프린터에 설정’ 클릭!

⑩‘닫기’ 클릭!

Off

Power Switch

Cover STD

Cover Roller L&R

Auto Cutter Wire

Auto Cutter GND Wire

Wire Hole

Cover DIP

Auto Cutter Wire

Auto Cutter GND Wire

Peeler Connector

Auto Cutter Connector

Auto Cutter GND Connector

Cover DIP

Otros manuales para XD Series

Este manual sirve para los siguientes modelos

Otros manuales de Etiquetadora de BIXOLON

BIXOLON

BIXOLON SLP-TX403R Manual de usuario

BIXOLON

BIXOLON SRP-770II Manual de usuario

BIXOLON

BIXOLON SLP-T400 Manual de usuario

BIXOLON

BIXOLON XT3-40 Series Manual de usuario

BIXOLON

BIXOLON SLP-TX403 Manual de usuario

BIXOLON

BIXOLON SPP-L3000 Manual de usuario

BIXOLON

BIXOLON XT Series Manual de instrucciones

BIXOLON

BIXOLON SLP-T400 Manual de usuario

BIXOLON

BIXOLON SRP 770 - B/W Direct Thermal Printer Manual de usuario

BIXOLON

BIXOLON SLP-DX220B Manual de usuario

BIXOLON

BIXOLON SLP-DL413 Manual de usuario

BIXOLON

BIXOLON SRP-E770III Series Manual de usuario

BIXOLON

BIXOLON XT5-43 Manual de usuario

BIXOLON

BIXOLON SLP-D420E Manual de usuario

BIXOLON

BIXOLON SRP-770III Manual de usuario

BIXOLON

BIXOLON XF3-40 Manual de usuario

BIXOLON

BIXOLON SRP-382II Instrucciones de instalación

BIXOLON

BIXOLON SLP-DL410KV Manual de usuario

BIXOLON

BIXOLON SRP-770IIE Manual de usuario

BIXOLON

BIXOLON XM7-40 Manual de usuario

BIXOLON

BIXOLON XD Series Instrucciones de instalación

BIXOLON

BIXOLON SLP-TX40xR Series Manual del propietario

BIXOLON

BIXOLON SLP-TX400R Manual del propietario

BIXOLON

BIXOLON XL5-40CT Series Manual de usuario

Manuales populares de Etiquetadora de otras marcas

Brother

Brother P-Touch 2420PC Manual de usuario

newell

newell Dymo LabelManager 210D Manual de usuario

Brother

Brother TD-4000 Manual de usuario

U-Line

U-Line BROTHER H-8754 Manual de usuario

Tharo Systems

Tharo Systems H-435+ Manual de usuario

Brother

Brother E300 Manual de usuario

Godex

Godex RT700 SERIES Manual de usuario

ID Technology

ID Technology 252 Manual de usuario

Labelmate

Labelmate MC-11 Manual de usuario

CAB

CAB XD4M/300 Manual de usuario

Avery Dennison

Avery Dennison Pathfinder 6057 Manual de servicio

Brother

Brother P-touch PT-9700PC Manual de usuario

TSC

TSC PEX1000 Series Manual de usuario

Adkins

Adkins Label Master Manual de usuario

Epson

Epson LabelWorks LW-400 Manual de usuario

Primera

Primera 510212 Manual de usuario

Brady

Brady BradyPrinter S3100 Manual de usuario

DuraLabel

DuraLabel LabPRO Manual de usuario