Billion BiPAC 7300GX Manual de usuario

BiPAC 7300GX

ADSL2/2+ Modem/Router with 3G back-up

QoS Firewall Wireless

Multi-Port Switching Hub

UK Quick Install Guide

LThis guide covers only the initial

Internet set-up. Please refer to

the full User Manual on the CD-

ROM for more advanced

settings. This guide is based on

the Billion BiPAC 7300GX

3G/ADSL2+ Wireless

Modem/Router. Screen shots in

this guide may vary slightly from

the actual router.

www.billion.uk.com

This symbol on the product or in the instructions means that your electrical and electronic

equipment should be disposed at the end of its life separately from your household waste.

There are separate collection systems for recycling in the EU.

For more information, please contact the local authority or your retailer where you purchased

the product.

QUICK INSTALL GUIDE

Billion 7300GX 3G/ADSL2+ Wireless Modem/Router Installation

1.1 Starting out:

Before you can establish an Internet connection through your Billion 7300GX

Modem/Router make sure you have the following:

1. A Computer or Notebook with an installed Network Adaptor (sometimes called

an Ethernet Adaptor, Network Card or NIC)

2. An ADSL or DSL service account and configuration information provided by

your Internet Service Provider (ISP). You should need only a User Name and

Password, but you can check with your ISP to see if you require any of the

other following configuration parameters to connect your Billion 7300GX

Modem/Router to the Internet :

a. ISP User Name and Password

b. VPI/VCI parameters

c. Multiplexing Method

d. Host and Domain Names

e. ISP Domain Name Server ( DNS ) Address

f. Fixed or Static IPAddress.

3. A compatible 3G datacard for 3G connectivity with SIM card (see

www.billion.uk.com/compatible-3G.htm for a full list of compatible cards) from

your mobile service provider.

4. Username and Password and APN from your mobile service provider.

1.2 Steps for Connection:

The following are the steps to properly connect your Billion 7300GX Modem/Router:

1. Turn off your computer.

2. If you do not have an ADSL faceplate installed by your service provider, you

must ensure ADSL splitters (also called microfilters or filters) are fitted to all

telephone sockets in use.

3. Connect the supplied ADSL (RJ-11) cable from the splitter/filter of your chosen

telephone socket (or ADSL faceplate if you have one) to the DSL Port of your

Billion 7300GX Modem/Router.

4. Connect the yellow Ethernet cable (RJ-45) from one of the Ethernet ports of your

Billion 7300GX Modem/Router to the Network Adaptor in your computer.

5. Insert your 3G datacard with SIM firmly into the slot at the back of the

Billion 7300GX Modem/Router. Ensure any “flip-out” antenna is deployed.

6. Connect the Power adaptor to the Billion 7300GX Modem/Router and plug the

other end into a Power outlet. Power up the unit.

7. Turn on your computer. Please allow up to 45 seconds for your Network Adaptor

to locate the Router. Please wait for the DSL light on the front of the router to turn

to solid – this may take up to 1-2 mins (see 3.1 Troubleshooting the connection).

8. You are now ready to configure your ADSL and Wireless connection for the

Billion 7300GX Modem/Router. All you need to do is to follow the instructions

that follow and enter your User Name and Password as supplied by your Service

Provider. No other changes should be necessary.

2.1 ADSL and Wireless Configuration:

1. Open Internet Explorer or your default web browser and type in

http://192.168.1.254 in the address bar (where you would normally enter the

web site address) as per the illustration below.

2. You will be presented with a user name and password prompt.* Simply enter

user name as admin, password as admin and click OK. This will take you to

the modem’s Status page.

* If the user name and password prompt box does not appear make sure that any

firewall or anti-virus such as Trend Micro or Norton is disabled. Also ensure that your

Internet settings are correct. (In Internet Explorer go to Tools/Internet

Options/Connections and make sure “Never dial a Connection” is checked. Then

Click on the LAN settings and ensure “Automatically detect settings” is checked and

all other fields are blank. Then go to Tools/Internet Options/Security and return your

Security settings to “default”. )

3. From the Menu on the left select Quick Start.

4. Ensure the Connect Mode is ADSL (Recommended) and click on Continue.

5. Enter your Username and Password as supplied by your Internet Service

Provider in the relevant fields, and click on Continue.

6. Please wait while the router applies the new settings.

7. Now click on Next to Wireless. N.B. If you do not go through the wireless

setup on the Wizard, then you must click Save Config at the bottom of the page

and then click Apply settings to save your username and password to Flash.

8. From the drop down menu in the Security Mode field you can choose your

preferred wireless security (or keep the wireless security disabled.) Please ensure

your wireless adaptor or laptop is compatible with your chosen security mode.

9. For WPA you should enter an alphanumeric password (numbers and letters) of

between 8 and 64 characters in the WPA Shared Key field and click Continue.

10. Please wait while the router applies the new settings.

11. This completes the wireless security configuration.

12. You should now be connected to the Internet. You can check your connection

on the Status page by selecting Status from the menu on the left-hand side.

13. You are now ready to set up your 3G connection.

To set up your 3G connection your 3G datacard with SIM must be inserted

firmly into the slot in the back of the router before powering up the device.

If your 3G card has a “flip-out” antenna then please ensure that this is

deployed after inserting the card into the slot, before powering up the device.

2.2 Setting up your 3G connection:

You can configure your 3G connection to act as a backup (Autofailover mode),

or as your primary connection.

In both cases your 3G datacard with SIM must be inserted firmly into the

slot in the back of the router before powering up the device.

If your have completed your ADSL and wireless configuration and your 3G

datacard was inserted when you first powered up the router, please select Status

from the menu on the left-hand side and go to section 2.3 to configure your 3G.

If you have configured your ADSL and wireless without inserting your 3G

datacard the Status page of the router should look like this.

1. In this case, please click Logout and power down the router.

2. Now insert you 3G datacard firmly into the slot in the back of the router,

ensuring any “flip-up” antenna is deployed, and turn the device back on. The 3G

light will flash and then should turn solid within 1 min (depending on your signal

strength). Please wait for the DSL light to turn solid. This may take 1-2 mins.

3. Your ADSL line will reconnect and you will need to access the router again

by typing http://192.168.1.254 in the address bar and logging in.

4. This should bring you to the router’s Status page. You are now ready to

configure your 3G connection.

Otros manuales para BiPAC 7300GX

Tabla de contenidos

Otros manuales de Enrutador inalámbrico de Billion

Billion

Billion BiPAC 8900AX(L)-2400 Manual de usuario

Billion

Billion BiPAC 7800NX Manual del propietario

Billion

Billion BiPAC 6200NXL Manual de usuario

Billion

Billion BIPAC 6500 Manual de usuario

Billion

Billion BiPAC 7300NX Manual de instalación y operación

Billion

Billion BIPAC-6500 Manual de usuario

Billion

Billion 7800VDP(O)X Manual de usuario

Billion

Billion BiPAC 7800(N)X(L) Manual de usuario

Billion

Billion BiPAC 7300NX Manual de usuario

Billion

Billion BiPAC 8800NL R2 Guía de configuración

Billion

Billion BiPAC 5200N RC Manual de usuario

Billion

Billion BiPAC 8800AXL Manual de usuario

Billion

Billion BiPAC 6300NX Manual de instalación y operación

Billion

Billion BiPAC 8800AXL Manual de usuario

Billion

Billion BiPAC 7300W Manual de usuario

Billion

Billion BiPAC 6404VGP Manual de usuario

Billion

Billion BiPAC 6300NXL Manual de usuario

Billion

Billion BIPAC 6500W Manual de usuario

Billion

Billion BiPAC 7800DXL Manual de usuario

Billion

Billion BiPAC 6200WZL R2 Manual de usuario

Billion

Billion BIPAC-7402W Manual de usuario

Billion

Billion SG600R2 Manual de usuario

Billion

Billion BiPAC 6300VNOZ Manual de usuario

Billion

Billion BiPAC 7800(N)X(L) Manual de usuario

Manuales populares de Enrutador inalámbrico de otras marcas

Milesight

Milesight UG67 Manual de usuario

Airlogic

Airlogic AirSync Class 1 Manual del propietario

Samsung

Samsung WCH730B Manual de usuario

TELEFONICA

TELEFONICA USB Adapter Manual de usuario

NETGEAR

NETGEAR PowerLINE WiFi 1000 Series Manual de usuario

Askey

Askey RAC2V1K Manual de usuario

Alloy

Alloy WLF2454AP-S Manual de usuario

TP-Link

TP-Link TL-WR542G Manual de usuario

NETGEAR

NETGEAR WNR2000v4 Manual de usuario

Hama

Hama 53120 Manual de usuario

Intellinet

Intellinet 524582 Manual de usuario

Asus

Asus RT-N10P Manual de usuario

D-Link

D-Link DIR-506L Manual de usuario

Sapido

Sapido GR297n Manual de usuario

Asus

Asus DSL-N55U Manual de usuario

AMTC

AMTC WR7502 Manual de usuario

Compaq

Compaq CP-2W - iPAQ Connection Point Manual de usuario

SMC Networks

SMC Networks WBR14-N2 FICHE Manual de usuario