BestScope BS-2080MH4 Manual de usuario

User Manual

Multi-viewing Microscope

BS-2080MH4/4A

BS-2080MH4 BS-2080MH4A

This manual is written for multi-viewing microscope BS-2080MH4 and BS-2080MH4A. For

safety, exerting best performance of the instrument, and making you familiar with the

instrument entirely, we strongly recommended that you carefully read this manual before using

the microscope.

BestScope International Limited

Contents　　　　　　　　　BS-2080MH4/BS-2080MH4A

Use Notices

1、Name of Components ……………………………………………………3

2、Installation ……………………………………………………………… 4

2-1、Order of Installation ……………………………………………………………4

2-2、Installation Steps ……………………………………………………………… 5

3、Adjustment ………………………………………………………………9

4、Operation ………………………………………………………………10

4-1、Primary Set Operation …………………………………………………… 10

4-2、Adjusting Minor Set ………………………………………………………… 15

5、Technical Specifications ………………………………………………… 16

6、Trouble Shooting …………………………………………………………17

BestScope International Limited

Use Notices BS-2080MH4/BS-2080MH4A

I. Safety note

1. Carefully open the box, avoid the accessories, like lens, dropping to ground and being damaged.

2. Do keep the instrument out of direct sunlight, high temperature or humidity, dusty and easy

shaking environment. Make sure the stage is smooth, horizontal and firm enough.

3. If the bacterium solution or the water splash to the stage, objective or viewing tube, pull out the

power cord at once, and wipe up the microscope. Otherwise, the instrument will be damaged.

4. When running, the lamp house and nearby parts will be very hot. Please ensure there is enough

cooling room for them.

5. Make sure the instrument is earthed, to avoid lighting strike.

6. For safety, be sure the main switch is in “O” (off) state before replace the halogen lamp or the fuse,

then cut off the power, and do the operation after the lamp bulb and the lamp house completely

cool.

7. Check the input voltage: be sure the input voltage which signed in the back of the microscope is

consistent with the power supply voltage, or it will bring a serious damage to the instrument.

8. Use the factory supplied power cord, please.

II. Maintenance

1. All the lenses have been well checked and adjusted. It is forbidden to disassemble them yourself.

2. The nosepiece and coarse/fine focus unit have a compact and precise frame, please don’t

disassemble them as possible as you can.

3. Keep the instrument clean, wipe dust regularly, and be attention to avoid contaminating the

optical elements especially.

4. The contaminations on the prism, as finger mark and oil, could be gently wiped with a piece of soft

cloth or tissue paper, gauze which has been immersed in pure alcohol or xylene. ( note that the

alcohol and the xylene are all burned easily, do not let them near the fire, and use them in a

drafty room as possible as you can.)

5. Don’t use organic solvent to wipe the non-optical elements, when you need to clean, use the soft

detergent, please.

6. When using, if the microscope is splash by liquid, cut off the power at once, and wipe up the

moisture.

7. Do not disassemble any parts of the microscope. That will affect the function or decline the

performance of the microscope.

8. Place the instrument in a cool, dry position. After using the microscope, remember to cover it

with dust helmet. Do wait for the lamp house cooling completely before cover.

BestScope International Limited

1.Name of Components BS-2080MH4/BS-2080MH4A

Primary Trinocular

Viewing Unit

Minor Binocular

Viewing Device

Connecting

Fitting

Body Teaching Image

Rotation Mirror

Right Minor

Column support

Microscope

Body

Video Port

Minor Binocular

Viewing Device

Primary Trinocular

Viewing Unit

Body Teaching Image

Rotation Mirror

Microscope Body

Lamp House

BestScope International Limited

2. Installation BS-2080MH4/BS-2080MH4A

2-1 Order of Installation

*The installation of BS-2080MH4A is similar to BS-2080MH4.

①Installing the Mechanical Stage

②Installing the Lamp House

③Installing the Objective

④Connecting Teaching Image Rotation Set

⑤Connecting Left\Right Minor Set

⑥Stack Mounting Teaching Image Rotation Set

⑦Stack Mounting Minor Set

⑧Installing the Trinocular Viewing Unit

⑨Installing Binocular Viewing Device

⑩Installing Eyepiece and Video Port (optional)

⑤

④

③

②

①

⑦

⑥

Objective

Video Port (optional)

Right Minor

Column Support

Trinocular Viewing Unit

Microscope Body

LED Pointer Image

Rotation Set

Lamp

House

Image Rotation

Connecting Tube (1)

Mechanical

Stage

Image Rotation

Connecting Tube (2)

⑨

⑧

⑩

BestScope International Limited

Figure 2

③

④

⑤

BS-2080MH4/BS-2080MH4A

2-2 Installing steps

Figure 3

2-2-1 Installation Body’s Chassis

1. Installing the Mechanical Stage

Support Device

Before installing the device, be sure to

adjust the coarse focus knob①. Make the

guide board②(see figure 1) down to the

lowest position, so you can install the

mechanical stage support device easily.

Hold on the mechanical stage support

device (figure 2), place it from the top of

the guide board (figure 1), let the device

(figure2) falling free until it reach the limit

position. Use the hexagon wrench screw

down the locking block③, make the stage

support device (figure1) and the guide

board fixed together.

The mechanical stage ⑤have been

adjusted horizontally with ④and fixed

together before leaving factory. Do not

disassembly unless necessary, that may

affect the observation precision of the

instrument.

Figure 1

②

①

BestScope International Limited

　BS-2080MH4/BS-2080MH4A

2-2-2 Installing and Replacing the Lamp

(figure4, 5)

Please use the specified halogen Lamp 6V30W①.

1. Hold the bulb①after you wrap it with gauze or

other protection materials, and then deeply insert

it into the lamp holder.

2. Replacing Lamp when using or soon after

When using, or soon after it is turned off, the

lamp, the lamp house and nearby parts will be

very hot and will cause serious burns. Please turn

the main switch②on “O” (off), pull out power

plug, and make sure the bulb, the lamp room and

periphery are all cool. Then, you can do your

replacing.

Please insert the lamp gently, or it will be

damaged by excessive extrusion

Do not touch the Halogen bulb with your bare

hands. It will shorten the service life or cause it

to burst. If you leave finger marks on the

surface carelessly, clean it with a dry soft

cloth.

2-2-3 Installing the Lamp House (figure 4, 5, 6)

Keep the bolt on the lamp house

(figure 4) in line with the jack on the back

of the microscope (like the show of figure

5), then pushing the lamp holder into the

illumination kits gently until they are

against each other (figure 6).

Figure 6

Jack

Figure 5

②

Figure 4

bolt

①

BestScope International Limited

　　BS-2080MH4/BS-2080MH4A

2-2-4 Installing the Objective

1. Adjusting the coarse focus knob until the

support device of the mechanical stage

reach its low limit position.

2. Wresting the lowest magnification

objective onto the nosepiece from the

left or the right side (figure 7), then

push the nosepiece clockwise, then

place other objectives by the sequence

of low to high magnification ( figure 8).

Installing objective this way will make

the change of magnification to be easier

while in using.

Clean the objective regularly, the

objective of the inversed microscope

is very sensitive to dust.

When operating, use 10 ×

magnification objective to search

specimen and focus firstly, then

replace with higher magnification

objective if necessary.

When replacing the objective, slowly

turning the nosepiece until you hear

“clicked”, that means the objective enter

the required position--the light path

center.

Figure 7

Figure 8

BestScope International Limited

螺钉

　　 BS-2080MH4/BS-2080MH4A

2-2-5 Installing Eyepiece

Pull out the lid of eyepiece which on the

eyepiece tube, insert eyepiece(figure 9)

into eyepiece tube until end. The result is

showing in the figure 12.

2-2-6 Installing Video Port (optional)

4. Insert the video port (figure 10) into the

trinocular unit (figure 11), then screw

down the bolt to fix it, the result is

showing in figure 12.

Figure 12

Figure 10

Figure 9

Figure 11

Eyepiece

bolt

Bolt

BestScope International Limited

3.Adjustment BS-2080MH4/BS-2080MH4A

Pointer Knob

Swing out Condenser (with

Aperture Diaphragm)

Video Port (optional)

Light Path Selector Lever

Lateral Adjustment Knob

Pointer rocker

Portrait Adjustment knob

Right Coarse Focus Knob

Main Switch

Right Coarse Focus Knob

Brightness

Adjustment Knob

Figure 13

Clocking Set

Left Coarse

Focus Knob

Left Fine Focus

Knob

Condenser Focus

Knob

Field Diaphragm

Figure 14

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Microscopio de BestScope

BestScope

BestScope BS-2040B Manual de usuario

BestScope

BestScope BS-2093B Series Manual de usuario

BestScope

BestScope BS-6000B Manual de usuario

BestScope

BestScope BS-3003 Manual de usuario

BestScope

BestScope BS-6045 Manual de usuario

BestScope

BestScope BS-2070 Manual de usuario

BestScope

BestScope BS-2080MH10 Manual de usuario

BestScope

BestScope BS-6002 Series Manual de usuario

BestScope

BestScope BS-7020 Manual de usuario

BestScope

BestScope BS-2030MH10 Manual de usuario

BestScope

BestScope BS-3070 Manual de usuario

BestScope

BestScope BS-2023B Manual de usuario

BestScope

BestScope BS-2064 Series Manual de usuario

BestScope

BestScope BS-3035 Series Manual de usuario

BestScope

BestScope BS-2081F Manual de usuario

BestScope

BestScope BS-5070B Manual de usuario

BestScope

BestScope BS-6004 Series Manual de usuario

BestScope

BestScope BLM2-241 Manual de usuario

BestScope

BestScope BS-2052 Series Manual de usuario

BestScope

BestScope BS-2046 Manual de usuario

BestScope

BestScope BS-3010A Manual de usuario

BestScope

BestScope BS-2052BDBD Manual de usuario

BestScope

BestScope BS-5092 Series Manual de usuario

BestScope

BestScope BS-6023 Series Manual de usuario

Manuales populares de Microscopio de otras marcas

Thermo Scientific

Thermo Scientific Nicolet iN10 Guía

National

National DC3-163 Manual de usuario

KERN Optics

KERN Optics OPE-1 Manual de usuario

OPTIKA MICROSCOPES

OPTIKA MICROSCOPES B-150D Manual de usuario

Prior

Prior Lux POL Manual de usuario

Opitec

Opitec Smartscoop 115615 Manual de usuario

KERN

KERN OPO-1 Manual de usuario

Topcon

Topcon SP-1P Manual de usuario

Motic

Motic PA43 Manual de usuario

Leica

Leica DVM5000 Guía del usuario

MshOt

MshOt MZ62 Manual de usuario

KERN Optics

KERN Optics OZR-5 Manual de usuario

VWR

VWR VisiScope 384 Series Manual de usuario

Nikon

Nikon ECLIPSE E200 POL Manual de usuario

Leica

Leica DI C800 Manual

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Manual de usuario

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Manual de usuario

Olympus

Olympus SZ61 Manual de usuario