Bestboard Beast Manual de usuario

- 1 -

Beastboard User Manual

©Beastboard Inc. 2020 https://beastboard.net/

Dear user,

Thank you for purchasing a Beast electric skateboard.Understanding the information in this

leaflet is the first step to take full advantage of all the performance of your board, while risks

associated with use.

Please read through all the information within this guidebook before you start to ride your

board.

CAUTIONS

Your board may disconnect with the remote controller at some time due to the radio

interference. Please be aware that you might risk injuries each time you ride an electric

skateboard. Make sure to read the following instructions before you start a ride.

1, Read User Guidebook Before Ride;

2, Make Sure to Wear Helmet and Other Protection Kits;

3, Please Abide By Local Traffic Rules and Regulations;

4, Do Not Ride on Wet Roads or Surfaces;

5, Always Check and Make Sure All the Screws Are Tightened;

6, Always Check the Remote Controller’s Battery Level;

- 2 -

7, Avoid Riding Downhill whit high speed Unless you are an expert;

8, Do Not Always Rely on Brakes and always think ahead to brake the board when in high

speed.

1. Risk of serious and fatal injuries :

Using the Beast skateboard can result in the risk of serious injury or fatal due to loss of control,

collision or fall.To reduce these risks, it is imperative to read and follow all instructions and

warnings of the instructions for using the Beast skateboard before first use.

2. Beast skateboard lifting and loading techniques :

Our electric skates are heavy objects and can weigh up to 8.9 kg. The transportation and

handling may cause injury. Use techniques of safe and proper lifting and loading.

Make sure the Skateboard is stopped before lifting it. It is recommended that the lifting

skateboarding is performed by two people, each placing both hands under the board. Lift the

skateboard with your leg strength not your back.

3. Lighting :

It is imperative in case use at night to use a powerful lighting system, allowing to see and to be

seen, like a bicycle light.

- 3 -

4. Vibrations and shocks :

The use of electric skates can generate significant vibrations and shocks in depending on the

surface on which it is used.Do not use your skateboard for too long, and if you experience

discomfort from vibration, stop immediately to use it.

5. Risk of burns :

After use, the motor and the variator emit a strong heat. So it is imperative not to touch these

two elements, at the risk of serious burns.

6. Electrical risk :

Electric skates, especially chargers, are subject to high voltages. It is therefore strictly

forbidden to disassemble the charger, as well as the battery pack, and in case of intervention

on the skateboard, it is imperative to disconnect the battery.

7. Responsibility :

The Beast Company declines all responsibility in the event use of your skateboard that does

not comply with the laws applicable in the country in force. When purchasing an Beast product,

users or the people who use them represent acknowledge having read the conditions of use

and do not can in no case turn against the company Beast in case of injury, death or disability

related to the use of the Beast skateboard.

- 4 -

8. Your skateboard (Beast-viper)is supplied with :

1 x Power Adapter and Charger.

1 x Wireless Remote (Different depending on the model chosen).

1 x T Wrench (with 3 Socket Sizes and HexKey/Screwdriver).

1 x USB Cable.

1x Data Defection Cable

- 5 -

Your skateboard (K8)is supplied with :

1 x Power Adapter and Charger.

1 x Wireless Remote (Different depending on the model chosen).

1 x T Wrench (with 2 Socket Sizes and HexKey/Screwdriver).

1 x USB Cable.

1x Data Defection Cable

- 6 -

Get to know the board

- 7 -

- 8 -

Get to Know the Remote

- 9 -

Charge the board

1, Connect the battery charger with the wall charging socket;

2,Plug in the socket and start charging the board;

3, When the board is charging, the charging brick will show red lights. When the board is fully

charged up, the red light turns green;

4, It is normal to have the charging brick very hot during the charging process. It will cool down

when it is fully charged up;

5, Please keep an eye on the board while it is charging. Do not charge it while nobody’s home

or everyone’s sleeping.

Turn on the Board & the Remote

1, Press the power button on the side of the enclosure. A red light will be flashing. That means

the board is on, but the remote is not yet on;

2, Long press the power button on the side of the remote for a few seconds. Let go of the

power button when the red lights are on;

3, When the the red light on the side of the enclosure stops flashing, that means the board is

connected with the remote. Usually your board and your remote are all pre-paired up before

leaving our factory. So after the board and remote are all turned on, you are ready to go;

Turn off the Board & the Remote

1, The board will turn itself off after a 5 minutes if left without any move;

- 10 -

2, Long press the power button on the side of the enclosure to turn off the board;

3, Long press the power button on the side of the remote to turn off the remote

How to Pair Beast with its Remote

1, Long press the power button on the side of the enclosure and the power

button on the remote at the same time for a few seconds;

2, The screen displays matching and enter into matching mode. The remote control displays

matching successfully, with two short vibration and once long vibration means completing

matching.

3, If customer still finds it difficult to pair up the board with the remote,

please do not hesitate to contact us at Beaseboards@gmail.com.

Changing Speed Modes

1, Make sure both the board and the remote are turned on;

2,Adjust the function button to change the Speed mode.The screen will show different mode.

Switch direction of skateboard

1, Double click Function Button, the remote control will short vibrate once(short vibrate for

100ms, the same below), the direction icon changes to“Backward arrow”;

2,In the state of backward, double click Function Button, the remote control will short vibrate

once, the direction icon changes to“Forward arrow”.

Note: This operation will be valid when the throttle trigger is in neutral position(zero

throttle) and the speed is less than 3km/h.

Tabla de contenidos

Manuales populares de Patineta y longboard de otras marcas

Walksmart

Walksmart Fuga Manual de usuario

Mattel

Mattel Fisher-Price DYH05 Manual de usuario

VOLTAWAY

VOLTAWAY POCKETROCKET 26 Manual de usuario

Lycaon Board

Lycaon Board Lycaon GR Manual de usuario

Ignite

Ignite ESK02 Manual de usuario

YUNEEC

YUNEEC E-GO Cruiser Manual de usuario

Miles

Miles Phantom Manual de usuario

Hudora

Hudora Skateboard Retro Instrucciones de montaje

fun pro

fun pro Mini Cruiser Manual de usuario

Beeper

Beeper RoadBoard SK1 Manual de usuario

Backfire

Backfire Ranger X3 Manual de usuario

Gyroor

Gyroor R1 Manual de usuario

MOOVI

MOOVI EB203A Manual de usuario

iSinwheel

iSinwheel V8 Manual de usuario

YUNEEC

YUNEEC E- GO Manual de usuario

OnlyOne

OnlyOne O-3 Manual de usuario

Clas Ohlson

Clas Ohlson 31-9262 Manual de usuario

Miles

Miles RAMPAGE Manual de usuario