Beltone MyPAL Micro Manual de usuario

Beltone myPAL Micro

Instructions for use

2 3

Statement:

This device complies with Part 15 of the FCC Rules and ICES-003

of the IC Rules. Operation is subject to the following two condi-

tions: (1) this device may not cause harmful interference, and (2)

this device must accept any interference received, including inter-

ference that may cause undesired operation.

Note: This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules and ICES-003 of the IC rules. These limits are de-

signed to provide reasonable protection against harmful interfer-

ence in a residential installation. This equipment generates, uses

and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful in-

terference to radio communications. However, there is no guaran-

tee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference

by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the re-

ceiver.

Welcome

Congratulations on your purchase of a Beltone myPAL Micro.

The myPAL Micro is a high quality portable speech and audio

streamer that streams speech and audio directly to your hearing

instrument.

Please read this manual carefully to fully beneﬁt from the myPAL

Micro. Ask your hearing care professional if you have any ques-

tions.

For further information you can also visit the www.beltone-hear-

ing.com web site.

For your safety, carefully read the chapter Important Information,

starting on page 29.

FCC ID : X26SM-2M

4 5

Operation is subject to the following two conditions:

1. this device may not cause interference, and

2. this device must accept any interference, including interference

that may cause undesired operation of the device.

For other identiﬁed applicable international regulatory require-

ments in countries outside EU and US, please refer to local coun-

try requirements for these areas.

In JP: Japanese Radio Law and Japanese Telecommunications

Business Law Compliance.

This device is granted pursuant to the Japanese Radio Law

(電波法) and the Japanese Telecommunications Business Law

(電気通信事業法). This device should not be modiﬁed (otherwise

the granted designation number will become invalid).

• Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Changes or modiﬁcations can void the user’s authority to operate

the equipment.

Intended use

To enable hearing instrument users to follow speech or listen to

other audio signals.

This product is in compliance with the following regulatory re-

quirements:

In EU: The device conforms to the Essential Requirements ac-

cording to Annex I of Council Directive 93/42/EEC for medical

devices (MDD) and Essential Requirements and other relevant

provisions of Directive 1999/5/EC (R&TTE).

The declaration of conformity may be consulted at

www.beltone-hearing.com

In US: FCC CFR 47 Part 15, subpart C

In Canada: IC 6941C-SM2M

6 7

Welcome..........................................2

Statement .........................................3

Intended use .......................................4

Description ........................................8

Getting Started ....................................10

Turning your myPAL Micro ON and OFF .................12

Pairing to your hearing instruments.....................12

Start streaming ....................................15

Stop streaming ....................................16

Wearing the myPAL Micro............................18

Status light indicator (LED) ...........................20

Volume control and mute ............................22

Mute light indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

Special features ...................................24

Test mode........................................26

Important Information ...............................28

General warnings ..................................29

General precautions ................................30

Built-in battery care ................................32

Battery warning....................................33

Charger care......................................34

Charger warning ...................................34

Technical speciﬁcations .............................36

Temperature test, transport and storage information .......36

Warranty .........................................36

What is covered by this warranty? .....................37

What is not covered by the warranty....................37

Troubleshooting guide ..............................38

Contents

8 9

6 Volume down

7 Mute button

8 Volume up

9 Mute light indicator (LED)

10 Paring button

11 Mounting clip

Description

1 Power button

2 Microphone inlet

3 Microphone inlet

4 Status light indicator (LED)

5 Micro USB for charging

710

6 8

10 11

Getting Started

Before using your myPAL Micro, you need to charge the re-

chargeable battery. To charge it, plug the charging cable into the

myPAL Micro as shown in the picture below.

Next, plug the other end of the charging cable into the charger

and into a power outlet.

During the charging process, the status LED indicator will show

a solid red light. When fully charged and still connected to the

charger, the LED will turn solid red, interrupted by a green blink

every 2 seconds.

Charging an empty battery typically takes about 3 hours. It is safe

to leave the charger connected overnight – the battery cannot be

overcharged.

• When charging your myPAL Micro for the ﬁrst time, let it charge

for at least 3 hours, even if the battery indicator indicates that

the battery is fully charged.

• For safety reasons, recharge the battery only with chargers

supplied by Beltone.

iNote: To protect the myPAL Micro when not in use, please

place it in carrying pouch delivered with the product.

Do not charge the myPAL Micro while it is on your body.

12 13

Turning your myPAL Micro ON and OFF

To turn the myPAL Micro ON, press and hold the Power button

(see page 8) for approximately 1.5 seconds, until the status LED

turns green. After releasing the Power button, the status LED will

blink green every 2 seconds.

To turn the myPAL Micro OFF, press and hold the ON/ OFF but-

ton for approximately 1.5 seconds, until the status LED turns red

– indicating that the unit is shutting down.

If the battery level is low, the status LED will blink orange once

every second.

Pairing to your hearing instruments i

Note! The following information is primarily intended for your hear-

ing care professional, who in most cases will complete the nec-

essary tasks needed before the myPAL Micro can be used with

your hearing instruments. However, the process is designed to be

simple and most people can do it themselves.

It is possible to pair up to three Beltone streaming devices - e.g.

one myPAL Micro and two TV Link 2s (optional Direct™ acces-

sory) - with a given pair of hearing instruments. Therefore, chan-

nel 1, 2 or 3 must be selected when starting the pairing process.

Pairing the myPAL Micro in channel 1

1. Make sure the myPAL Micro is turned ON. Your hearing instru-

ments must be OFF – open the battery doors.

2. With the tip of a pen

or similar object, press

the small pairing but-

ton once, as shown in

the picture to the right.

The status LED will now

blink orange once every

2 seconds to indicate that

the myPAL Micro is ready

to be paired in channel 1.

Your myPAL Micro will remain in Pairing mode for 20 seconds.

3. While in Pairing mode, close the battery doors on both hear-

ing instruments and make sure they are ON. A successful

pairing will be indicated by an audible melody being played in

both hearing instruments and the status LED (see page 8) will

stay solid orange for 3 seconds. You are now ready to use the

myPAL Micro!

14 15

Start streaming

Turn ON the myPAL Micro and make sure your hearing instru-

ments are turned ON. Streaming can be started in one of three

ways.

1. Press and hold the push or toggle button on both hearing

instruments for about three seconds in order to listen to a

streamed audio signal*. If ear to ear program coordination is

activated in you hearing instruments, you only have to activate

streaming on one of the hearing instruments.

2. If you have a Beltone Direct™ Remote Control (optional

accessory), simply press the streaming button on the

Remote Control*.

3. If you use a Beltone app offering remote control functional-

ity, simply select the myPAL Micro program in the program

screen*.

*Once the hearing instruments connect to the myPAL Micro, a

short “streaming activation” melody will play in your hearing in-

struments followed by the streamed sound.

Start streaming from a 2nd or 3rd streaming device

If your hearing instruments are paired to more than one stream-

ing device, you can start streaming from one of these devices in

three ways.

Pairing button

pushes Light indicator pattern Channel

1 1

2 2

3 3

Successful

pairing

Indication

Pairing the myPAL Micro in channel 2 or 3 (For people using more

than one streaming device)

To pair the myPAL Micro in channel 2, press the pairing button

twice. The status LED will now blink yellow twice every 2 seconds

to indicate that it is ready to be paired in channel 2. Close the bat-

tery doors on the hearing instruments.

To pair the myPAL Micro in channel 3, press the pairing button

three times. The LED will now blink yellow three times every 2

seconds to indicate that it is ready to be paired in channel 3.

Close the battery doors on the hearing instruments.

Pairing blinking pattern:

16 17

1. Press and hold the hearing instrument program button for

about 3 seconds two or three times in a row to access the 2nd

or 3rd Beltone streaming device.

2. If you use a Direct™ Remote Control (optional accessory),

press the streaming button on the Direct™ Remote Control

a 2nd or 3rd time to access the 2nd or 3rd Beltone streaming

device.

3. If you use a Beltone app offering remote control functionality,

simply select the desired streaming program in the program

screen.

Stop streaming

Streaming can be stopped in the following three ways:

1. Push the program button on your hearing instruments once*.

2. If you have a Beltone Direct™ Remote Control (optional ac-

cessory), press the “P” button, located in the center of the key

pad*. You may also press the home button to return to your

default settings.

3. If you use a Beltone app, select the desired program in the

program screen.

*This will return the hearing instruments to the last program used.

iNote! You may get out of range from your myPAL Micro. If

your myPAL Micro gets out of range and in range again within

5 minutes, your hearing instruments will automatically reconnect

and continue streaming. This also applies if the myPAL Micro is

turned off and on again within 5 minutes.

18 19

Wearing the myPAL Micro

Clip your myPAL Micro on the speaker’s jacket or other clothing

or hang it around the neck using included the lanyard. Place the

device within a range of 10-40cm (4-16 inches) from the speaker’s

mouth. When using the clip, make sure that the myPAL Micro

is mounted vertically with the Status LED pointing towards the

mouth.

10 - 40 cm

4-16 inches

Tabla de contenidos

Otros manuales de Audífono de Beltone

Beltone

Beltone Change BTE Manual de usuario

Beltone

Beltone IIC Series Manual de usuario

Beltone

Beltone LND1776-DW Manual de usuario

Beltone

Beltone OR65DI Manual de usuario

Beltone

Beltone OR364-DVIR Manual de usuario

Beltone

Beltone Paris 60 BTE Manual de usuario

Beltone

Beltone AMAZE Manual de usuario

Beltone

Beltone Rely 76 Manual de usuario

Beltone

Beltone 86 Manual de usuario

Beltone

Beltone AMZ663-DRW Manual de usuario

Beltone

Beltone CHG75 Manual de usuario

Beltone

Beltone myPAL Pro Manual de usuario

Beltone

Beltone ACS 85 Manual de usuario

Beltone

Beltone TO1715 Manual de usuario

Beltone

Beltone Imagine Manual de usuario

Beltone

Beltone EazyTrim Plus EZTP73-V BTE Manual de usuario

Beltone

Beltone ALLY Manual de usuario

Beltone

Beltone X26SY312 Manual de usuario

Beltone

Beltone Imagine IMG1763-DRWC Manual de usuario

Beltone

Beltone Imagine IMG17CIC-LP Manual de usuario

Beltone

Beltone IDT66D Open Manual de usuario

Beltone

Beltone RLY464-DRW Manual de usuario

Beltone

Beltone IDT35D HPGIDT45/45 HPG and IDT45D/45D HPG Manual de usuario

Beltone

Beltone Mira Series Manual de usuario

Manuales populares de Audífono de otras marcas

Sonic

Sonic Bliss miniBTE Manual de usuario

Lexie

Lexie B1 Manual de lista de piezas

Widex

Widex FM+DEX Manual de usuario

Siemens

Siemens Triano Manual de usuario

Camplicomms

Camplicomms HC-200 Manual de usuario

Widex

Widex SUPER 220 S2-VSD Manual de usuario

Phonak

Phonak Q90 Manual de usuario

Williams Sound

Williams Sound SoundPlus WIR 237 Guía

Oticon Medical

Oticon Medical Ponto SoundConnector Manual de usuario

Siemens

Siemens Life micon Manual de usuario

Starkey

Starkey Destiny Manual de usuario

Audicus

Audicus The Icon Manual de usuario

Advanced Bionics

Advanced Bionics Slim HP Standard Manual de usuario

Widex

Widex DREAM440 THE DREAM SERIES Manual de usuario

Phonak

Phonak myPilot Manual de usuario

NIKEN

NIKEN NK-401 Manual de usuario

ON Semiconductor

ON Semiconductor Ezairo 7111 Pre Suite Manual de usuario

Sonetik

Sonetik GOHEAR Manual de usuario

Beltone myPAL Micro Manual de usuario

Manuales populares de Audífono de otras marcas