Belden HIRSCHMANN GRS105 Manual de usuario

Installation GRS105/GRS106

Release

11/2021

Technical support

https://hirschmann-support.belden.com

User Manual

Installation

Industrial Ethernet Workgroup Switch

GRS105/GRS106

2021-11-02 Installation GRS105/GRS106

Release

11/2021

The naming of copyrighted trademarks in this manual, even when not specially indicated, should

not be taken to mean that these names may be considered as free in the sense of the trademark

and tradename protection law and hence that they may be freely used by anyone.

translation, conversion into any electronic medium or machine scannable form is not permitted,

either in whole or in part. An exception is the preparation of a backup copy of the software for

your own use.

The performance features described here are binding only if they have been expressly agreed

when the contract was made. This document was produced by Hirschmann Automation and

Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right

to change the contents of this document without prior notice. Hirschmann can give no guarantee

in respect of the correctness or accuracy of the information in this document.

Hirschmann can accept no responsibility for damages, resulting from the use of the network

components or the associated operating software. In addition, we refer to the conditions of use

specified in the license contract.

You can get the latest version of this manual on the Internet at:

https://www.doc.hirschmann.com

Hirschmann Automation and Control GmbH

Stuttgarter Str. 45-51

72654 Neckartenzlingen

Germany

Installation GRS105/GRS106

Release

11/2021 3

Contents

1 About this manual 7

2 General safety instructions 8

2.1 Warning symbols 9

2.2 Intended use 10

2.3 National and international safety regulations 10

2.4 Installation site requirements 10

2.5 Qualification requirements for personnel 11

2.6 Device casing 11

2.7 Strain relief 12

2.8 Shielded ground 12

2.9 Electrical connections 12

2.9.1 Grounding the device 12

2.9.2 Requirements for connecting electrical wires 12

2.9.3 Requirements for connecting the supply voltage 13

2.9.4 Requirements for connecting the signal contact 13

2.10 LED or laser components 13

2.11 Recycling note 14

3 Approvals 15

3.1 CE marking 15

3.2 UKCA marking 16

3.3 FCC note 17

3.4 Relevant for installations in switch cabinets according to

UL 60950-1/UL 62368-1 17

4Key 19

5 Description 20

5.1 General device description 20

5.2 Device name and product code 21

5.3 Device views 22

5.3.1 Front view device variant GRS106-6F8F16T... 22

4Installation GRS105/GRS106

Release

11/2021

5.3.2 Front view device variant GRS106-6F8T16T... 22

5.3.3 Rear views 23

5.3.4 Port assignment 24

5.4 Supply voltage 25

5.4.1 Supply voltage characteristic value G 26

5.4.2 Supply voltage characteristic value M 26

5.4.3 Supply voltage characteristic value L 27

5.5 Ethernet ports 28

5.5.1 10/100/1000 Mbit/s twisted pair port 28

5.5.2 100/1000/2500 Mbit/s twisted pair port 28

5.5.3 1/2.5 Gbit/s F/O port 29

5.5.4 1/2.5/10 Gbit/s F/O port 29

5.6 Management interfaces 30

5.6.1 Signal contact 30

5.6.2 Management interface MGMT (external

management) 31

5.6.3 SD card interface 33

5.7 Display elements 34

5.7.1 Device Status 34

5.7.2 Port status 36

6 Installation 39

6.1 Checking the package contents 39

6.2 Installing the SD card (optional) 40

6.3 Installing an SFP transceiver (optional) 41

6.4 Installing the device 41

6.5 Grounding the device 47

6.6 Connecting the terminal blocks 48

6.6.1 Supply voltage characteristic value M 48

6.6.2 Supply voltage characteristic value L 49

6.6.3 Signal contact 50

6.7 Connecting data cables 50

6.8 Filling out the inscription label 51

7 Operating the device 52

8 Making basic settings 53

Installation GRS105/GRS106

Release

11/2021 5

8.1 Default settings 53

8.2 First login (Password change) 54

9 Maintenance and service 55

10 Monitoring the ambient air temperature 56

11 Monitoring the ambient humidity 57

12 Disassembly 58

12.1 Removing the device 58

12.2 Removing an SFP transceiver (optional) 59

12.3 Removing the SD card (optional) 60

13 Technical data 61

13.1 General technical data 61

13.2 Supply voltage 61

13.3 Power consumption/power output 62

13.4 Signal contact 62

13.5 Climatic conditions during operation 63

13.6 Climatic conditions during storage 63

13.7 Dimension drawings 64

14 EMC and immunity 65

15 Network range 67

15.1 10/100/1000 Mbit/s twisted pair port 67

15.2 100/1000/2500 Mbit/s twisted pair port 67

15.3 Gigabit Ethernet SFP transceiver 68

15.4 Bidirectional Gigabit Ethernet SFP transceiver 69

15.5 2.5 Gigabit Ethernet SFP transceiver 71

15.6 10 Gigabit Ethernet SFP+ transceiver 71

15.7 DAC cables 72

16 Scope of delivery 73

6Installation GRS105/GRS106

Release

11/2021

17 Order numbers 73

18 Accessories 73

19 Underlying technical standards 76

A Further support 77

Installation GRS105/GRS106

Release

11/2021 7

1 About this manual

The “Installation” user manual contains a device description, safety

instructions, a description of the display, and the other information that you

need to install the device.

The Network Management Software Industrial HiVision provides you with

options for smooth configuration and monitoring. You find further information

on the Internet at the Hirschmann product pages:

https://www.hirschmann.com/en/QR/INET-Industrial-HiVision

Documentation mentioned in the “User Manual Installation” that is not

supplied with your device as a printout can be found as PDF files for

downloading on the Internet at: https://www.doc.hirschmann.com

8Installation GRS105/GRS106

Release

11/2021

2 General safety instructions

Note: Read these instructions carefully, and familiarize yourself with the

device before trying to install, operate, or maintain it. The following notes may

appear throughout this documentation or on the device. These notes warn of

potential hazards or call attention to information that clarifies or simplifies a

procedure.

You operate this device with electricity. Improper usage of the device entails

the risk of physical injury or significant property damage. The proper and safe

operation of this device depends on proper handling during transportation,

proper storage and installation, and careful operation and maintenance

procedures.

Before connecting any cable, read this document, and the safety

instructions and warnings.

Operate the device with undamaged components exclusively.

The device is free of any service components. In case of a damaged or

malfunctioning device, turn off the supply voltage and return the device to

Hirschmann for inspection.

WARNING

UNCONTROLLED MACHINE ACTIONS

To avoid uncontrolled machine actions caused by data loss, configure all

the data transmission devices individually.

Before you start any machine which is controlled via data transmission, be

sure to complete the configuration of all data transmission devices.

Failure to follow these instructions can result in death, serious injury,

or equipment damage.

Installation GRS105/GRS106

Release

11/2021 9

2.1 Warning symbols

This is a general warning symbol. This symbol alerts you to

potential personal injury hazards. Observe all safety notes that

follow this symbol to avoid possible injury or death.

If this symbol is displayed in addition to a safety instruction of the

type “Danger” or “Warning”, it means that there is a danger of

electric shock and failure to observe the instructions will inevitably

result in injury.

This symbol indicates the danger of hot surfaces on the device. In

connection with safety instructions, non-observance of the

instructions will inevitably result in injuries.

DANGER

DANGER draws attention to an immediately dangerous situation, which will

inevitably result in a serious or fatal accident if not observed.

WARNING

WARNING indicates a potentially hazardous situation which, if not avoided,

could result in death or serious injury.

CAUTION

CAUTION indicates a possible danger which, if not avoided, may result in

minor injuries.

NOTICE

NOTICE provides information about procedures that may result in

equipment or environmental damage.

10 Installation GRS105/GRS106

Release

11/2021

2.2 Intended use

Use the product only for the application cases described in the

Hirschmann product information, including this manual.

Operate the product only according to the technical specifications.

See “Technical data” on page 61.

Connect to the product only components suitable for the requirements of

the specific application case.

2.3 National and international safety

regulations

Verify that the electrical installation meets local or nationally applicable

safety regulations.

2.4 Installation site requirements

Exclusively operate the device at the specified ambient temperature

(temperature of the ambient air at a distance of 5 cm (2 in) from the device)

and at the specified relative humidity.

When you are selecting the installation location, make sure you observe

the climatic threshold values specified in the technical data.

Use the device in an environment with a maximum pollution degree that

complies with the specifications in the technical data.

See “Technical data” on page 61.

If the device is not installed horizontally, it must be installed in a switch

cabinet or other fire enclosure. The fire enclosure can be made of metal

or plastic with fire protection properties of at least V-1 according to

IEC 60695-11-10. The maximum diameter of bottom openings in the fire

enclosure is 2 mm (0.078 in).

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cambiar de Belden

Belden

Belden HIRSCHMANN PTN-CSM310-A Manual de usuario

Belden

Belden Hirschmann MACH4002 Series Manual de usuario

Belden

Belden HIRSCHMANN OCTOPUS OS24 Series Manual de usuario

Belden

Belden grass valley MASTERPIECE 12G-SDI Manual de usuario

Belden

Belden HIRSCHMANN MACH4002-48+4G Manual de usuario

Belden

Belden Hirschmann MACH104 Series Guía del usuario

Belden

Belden HIRSCHMANN EESX Series Guía de configuración rápida

Belden

Belden HIRSCHMANN RSPE 30 Manual de usuario

Belden

Belden Hirschmann HiOS-2S Manual de usuario

Belden

Belden HIRSCHMANN BRS20 Manual de usuario

Belden

Belden Hirschmann SPIDER II 8TX Manual de usuario

Belden

Belden Hirschmann GREYHOUND GRS1042 Manual de usuario

Belden

Belden Hirschmann RS20 Series Manual de usuario

Belden

Belden HIRSCHMANN OCTOPUS OS3 Manual de usuario

Belden

Belden Hirschmann SPIDER 8TX EEC Manual de usuario

Belden

Belden Hirschmann SPIDER Standard Line Series Manual de usuario

Belden

Belden HIRSCHMANN HiOS-2A Manual de usuario

Belden

Belden Hirschmann SPIDER 8TX EEC Manual

Belden

Belden Grass Valley K-Frame Cómo utilizar

Belden

Belden Hirschmann MAMMUTHUS MTS2600 Manual de usuario

Belden

Belden HIRSCHMANN MACH 100 Series Manual de usuario

Belden

Belden grass valley GV FABRIC Manual de usuario

Belden

Belden HIRSCHMANN SPIDER II 16TX EEC Manual de usuario

Belden

Belden Telecast Fiber Systems THOR-SLG Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario