basIP AA-07FB Manual de usuario
AA-07FB
entrance PANEL
quickstart guide
Full User Manual
wiki.bas-ip.com
123
456
7 8 9
0
*#T
2
1Backlight
Loudspeaker
AA-07FB SILVER multi apartment panel is an excellent solution for office
buildings, apartment complexes and cottage communities.
A distinctive feature of this panel is a color TFT screen with backlight,
as well as a high-resolution IP camera with wide viewing angles.
3Camera
44.3’’ Display
5Proximity sensors
6
7
Keypad
Reader
ENTRANCE PANEL MAIN SCREEN
main screen
On the main screen, you can find information about:
• Data that must be entered to call the apartment (to call the required apartment, you need
to enter from 4 to 10 digits, depending on the current panel mode);
• The combination that must be entered to call the concierge (to call the concierge, you must
enter the combination 0000 # or press the concierge or info button in the upper right
corner of the keypad /);
• A button that opens the access code menu (to open the menu press #,
enter the access code, and press #to confirm);
• A button to cancel an action or go back to previous the menu (press * to cancel);
Buttons that open the address book, which displays a list of contacts (sorted by name)•
for searching and calling an apartment if the exact logical address of the monitor is not known
(to open the address book, press the up / down arrows , and then press #to call).
By default, the address book is disabled, you can enable the option in the Apartments section
of the web interface.
i
Press «*» to exit the main screen or it
will be done automatically, after 30 sec
of inactivity.
The current statuses of the devices
connection to the network and SIP are
also displayed in the lower right corner.
You can change the text displayed on the main
screen in the Advanced tab of the web interface.
You can open basic settings from a panel or a web interface.
To enter the system settings, you must:
• Press the #button twice (the inscription Admin will appear on the screen).
Enter the admin password (the default password is 123456)•
Press #to confirm. This will open the settings menu.•
Use the Up / Down arrows or the 2 / 8 buttons on your keypad to move between menus
and fields. To confirm press the #button, and * if you need to go back.
ENTRANCE PANEL SETTINGS
HOW TO OPEN SETTINGS MENU?
Device Settings
In this menu, you can configure:
Panel operation mode•
• Wall mode is used when the panel is installed on the perimeter of the object.
If this variant is chosen, on the panel you must enter Building No., Unit No., Floor No., and Apartment No.
to call the necessary monitor.
Unit mode is required if the panel is installed near the unit entrance.•
When using this mode, it is enough to enter Floor No. and Apartment No. to call the necessary monitor.
• Device language (Russian, English, Ukrainian, Spanish, Polish, or Dutch)
• Panel logical address (Building No., Unit No., and Device No.)
For correct functioning, the panel and the monitor must have the same building and unit number
in apartment settings. Also for monitors, you must indicate corresponding information about the floor,
apartment, and device number.
If you have more than 1 entrance panel with the same logical address, you need to specify their
device numbers, starting from 1 for the main device, and from 2 to 9 for others.
• Admin password to enter device settings and web interface
Level of panel speaker volume•
Panel camera stream resolution (640х480 / 1280х720 / 1920x1080 (optional))•
Network settings
Here you can turn on/off DHCP connection and get network settings automatically
or enter it manually.
For correct panel work you must enter:
Panel IP address.•
By default, a device can have a static IP address 192.168.1.90 or 192.168.1.91
• Subnet mask
• The main gateway
• DNS server address
• Server is necessary if Link software is installed
Access settings
In this menu, you can set:
Lock open timeout is a period (1-300 sec) during which relay contacts will be closed•
or open (depending on the lock type), and a lock will stay open
Lock open delay is a period (1-300 sec) after which relay contacts will close or open after•
sending a signal to open a lock
Floor number (Elev Refer) where the panel is installed for further lift control module•
EVRC-IP use (optional).
Password (no more than 8 characters) is a general code entered on a panel keypad•
to open a lock. The default password is 0000.
Face settings
Enable / disable the feature•
Select similarity level (the lower the similarity level, the greater the error can be in scanning•
a face and granting access):
Low: the minimal similarity is necessary for access (changes in appearance (glasses, beard,•
presence of a hat) will not be taken into account)
Normal: some changes in appearance are taken into account, but not detailed•
(recommended for homes and offices)
High: the maximum similarity is necessary for access (recommended for high-security•
places)
• Select the appropriate mode:
Software: the software recognition algorithm is used, and there is a possibility of giving•
access by photos
Anti-spoofing: more detailed software recognition algorithm is used to prevent access•
by photos
3D (is available for panels with a built-in 3D sensor): detailed face recognition using•
IR sensors and building a face heat map to prevent spoofing
• Turn on/off automatic face recognition when motion is detected.
When a person approaches a panel (at a distance up to 50 cm) motion sensor becomes
active, and a panel will exit standby mode and turn on the face recognition feature.
• Register new face to the panel memory
We recommend adding a face ID by uploading photos via the web interface, because faces added using
the method below will not be displayed in the web interface of the panel, so it will be impossible to link
it to a user.
How to add face ID via the graphical
interface:
In the Register column, press #•
and enter any number.
Press #again and stand in front•
of the camera for scanning.
• After a beep, the face will be added
to the panel memory.
• Delete all previously added faces
Misc settings
In this menu, you can:
Add a user access card to the panel memory•
You can add a card both in this menu and in the web interface (see the «Access management»
or «Identifiers» section).
To add a card via the panel interface:
Enter a random number in the RoomNum field•
Bring the card to the reader area.•
You will hear a beep as confirmation that the card is added. Also, its number will be shown in the Card field.
The card number will be displayed in the Identifiers tab of the web interface, where you can add all•
the necessary information about the user and link the card to the corresponding apartment.
Reboot the panel.•
To do it, you must enter 1 and press #.
Reset panel settings to default settings.•
To do it, you must enter 1 and press #.
Panel reset will delete all cards.
About system
This menu displays
information about:
Framework versions (FW)•
Firmware versions (UI)•
Current IP address (IP)•
Current MAC address (MAC)•
SIP connection status (SIP)•
Otros manuales para AA-07FB
1
Tabla de contenidos
Otros manuales de Sistema de intercomunicación de basIP
basIP
basIP AV-01D Manual de usuario
basIP
basIP AQ-07LW Manual de usuario
basIP
basIP AA-07FB Manual de usuario
basIP
basIP SP-03F Manual de usuario
basIP
basIP AA-14FBS Manual de usuario
basIP
basIP AT-07L Manual de usuario
basIP
basIP AZ-07L Manual de usuario
basIP
basIP AV-04SD Manual de usuario
basIP
basIP AA-12 Series Manual de usuario
basIP
basIP AV-08FB Manual de usuario
basIP
basIP AA-12FB Manual de usuario
basIP
basIP BA-12BD Manual de usuario
basIP
basIP BI-02FB Manual de usuario
basIP
basIP AA-07FB Manual de usuario
basIP
basIP AV-01 Hoja de instrucciones
basIP
basIP AA-07FB Manual de usuario
basIP
basIP AV-04SD Manual de usuario
basIP
basIP AA-07B Manual de usuario
basIP
basIP AV-03D Manual de usuario
basIP
basIP AT-10 Manual de usuario
