Badger Meter M-series Guía de inicio rápido

M-Series® M2000

Connecting a Badger Meter Endpoint to the M2000

Application Brief

IAB-185-01-EN (August 2012)

OVERVIEW

This document describes the connection of a Badger Meter-

supplied endpoint (transmitter), such as an ORION® or GALAXY®

RTR®, or Itron® 100WP or 60WP to an M2000 Mag Meter.

QUICK SETUP FOR TOTALIZER AND FLOW UNIT

M2000 Front Panel Buttons

1. Navigate to Start Menu > Quick Setup > Flow Unit.

2. Select the desired unit of measurement.

3. Navigate to Start Menu > Quick Setup > Totalizer Unit.

4. Select the desired unit of measurement.

PROGRAMMING THE M2000 FOR THE ENDPOINT

Programming for Output #1

1. Navigate to Start Menu >Main Menu > Inputs/Outputs >

Digital Output 1 >Pulses/Unit.

2. Select the desired values.

NOTE: If the Pulse/Unit value is too high, error 110 will display

when you save. The Pulses/Unit and Full Scale Flow

parameters are dependent values that cannot exceed

10 kHz. To correct the error, decrease either or both of the

Pulse/Unit and the Full Scale Flow values.

3. Navigate to Select Function > AMR (50 ms pulse).

4. Press Efour times until the menu text is at Exit This Menu

to exit the programming.

Programming for Output #2

1. Navigate to Start Menu >Main Menu > Inputs/Outputs >

Digital Output 2 >Pulses/Unit.

2. Select the desired values.

3. Navigate to Start Menu >Main Menu > Inputs/Outputs >

Digital Output 1 >Pulses/Width.

4. Set the value to 0050 ms.

5. Press Efour times until the menu text is at Exit This Menu

to exit the programming.

ADDITIONAL NOTES

If the M2000 displays a reading, it will be necessary to either

program the endpoint to match the same reading on the M2000,

or reset the totalizer(s). The M2000 has a separate Unit Multiplier

setting in the Advanced menu that establishes the resolution of the

totalizer reading on the display. This multiplier displays a seven-digit

reading and is set to OFF from the factory. The endpoint must be

programmed to coincide with the value set in the Pulses/Unit and

the Unit Multiplier. For example, if the Unit Multiplier is set to 100

and the Pulse/Unit is set to 0000000.010, the reading on the display

would be 1234500 (the endpoint should be programmed to 12345).

To use the reading from the endpoint in the Reading Data

Management Software, the correct Test Circle Code will also need

to be added in the software. The Test Circle Code will depend on the

Pulses/Unit that was programmed into the M2000.

WIRING AN ORION OR GALAXY RTR ENDPOINT TO

THE M2000

Use either Output #1 or #2 when connecting an endpoint to the

M2000. Output #1 is the recommended option, as an AMR function

exists that will make for easier programming.

To connect the endpoint to Output #1, connect the endpoint wires

this way:

• Terminal 1: Red

• Terminal 2: Black and Green

• Remove jumper JP1 (output #1)

To connect the endpoint to Output #2, connect the endpoint wires

this way:

• Terminal 3: Red

• Terminal 4: Black and Green

• Remove jumper JP2 (output #2)

WIRING AN ITRON 100WP OR 60WP ENDPOINT TO

THE M2000

To connect the endpoint to Output #1, connect the endpoint wires

this way:

• Terminal 1: Red and White

• Terminal 2: Black

• Remove jumper JP1 (output #1)

To connect the endpoint to Output #2, connect the endpoint wires

this way:

• Terminal 3: Red and white

• Terminal 4: Black

• Remove jumper JP2 (output #2)

www.badgermeter.com

M-Series is a registered trademark of Badger Meter, Inc. Other trademarks appearing in this document are the property of their respective entities.

Due to continuous research, product improvements and enhancements, Badger Meter reserves the right to change product or system specications without notice, except to the extent an outstanding

Czech Republic | Badger Meter Czech Republic s.r.o. | Maříkova 2082/26 | 621 00 Brno, Czech Republic | +420-5-41420411

Slovakia | Badger Meter Slovakia s.r.o. | Racianska 109/B | 831 02 Bratislava, Slovakia | +421-2-44 63 83 01

Otros manuales para M-series

Este manual sirve para los siguientes modelos

Otros manuales de Instrumento de medición de Badger Meter

Badger Meter

Badger Meter ORION SE Guía de instalación y uso

Badger Meter

Badger Meter Recordall Turbo Series Manual de usuario

Badger Meter

Badger Meter iSonic 4000 Manual de usuario

Badger Meter

Badger Meter Cox Manual de usuario

Badger Meter

Badger Meter Blancett B114-110 Manual de usuario

Badger Meter

Badger Meter MN-MR100 Instrucciones y recetas

Badger Meter

Badger Meter ModMAG M1000 Manual de usuario

Badger Meter

Badger Meter ModMAG M1000 Manual de usuario

Badger Meter

Badger Meter Orion AL Series Manual de usuario

Badger Meter

Badger Meter Dynasonics Polymer RS-900w Manual de usuario

Badger Meter

Badger Meter FMS-3 Manual de usuario

Badger Meter

Badger Meter HR-LCD 4-20 Manual de usuario

Badger Meter

Badger Meter Impeller Data Industrial 3050 Series Manual de usuario

Badger Meter

Badger Meter PortaSonic 9000 Manual de usuario

Badger Meter

Badger Meter ER-10 Manual de usuario

Badger Meter

Badger Meter E G2 Series Manual de usuario

Badger Meter

Badger Meter M5000 Manual de usuario

Badger Meter

Badger Meter ModMAG M Series Manual de usuario

Badger Meter

Badger Meter ModMAG M-Series M7600 Manual de usuario

Badger Meter

Badger Meter Dynasonics UHC100 Manual de usuario

Badger Meter

Badger Meter epm-3 Manual de usuario

Badger Meter

Badger Meter Oval Gear EPM2-STD Manual de usuario

Badger Meter

Badger Meter Blancett B3100 Series Manual de referencia

Badger Meter

Badger Meter ModMAG M1000 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario