AZZA PT-5IVL Manual de usuario

PT-5IVL

SYSTEM BOARD

( VER. 1.x )

OPERATION MANUAL

PT-5IVL SYSTEM BOARD TABLE OF CONTENTS

TABLE OF CONTENTS

Chapter & Section Page

1. INTRODUCTION 1-1

1.1 SYSTEM OVERVIEW 1-1

1.2 FEATURES 1-1

2. SPECIFICATIONS 2-1

3. SYSTEM BOARD LAYOUT 3-1

3.1 PT-5IVL VER. 1.2 3-1

4. HARDWARE SETUP 4-1

4.1 UNPACKING 4-1

4.2 HARDWARE CONFIGURATION 4-1

4.2.1 DRAM INSTALLATION 4-1

4.2.2 L2 CACHE MEMORY INSTALLATION 4-2

4.2.3 CONNECTORS 4-3

4.2.4 JUMPERS 4-6

5. AWARD BIOS SETUP 5-1

5.1 GETTING STARDED 5-1

5.2 MAIN MENU 5-2

5.3 CONTROL KEYS 5-2

5.4 STANDARD CMOS SETUP 5-3

5.5 BIOS FEATURES SETUP 5-4

5.6 CHIPSET FEATURES SETUP 5-5

5.7 POWER MANAGEMENT SETUP 5-6

5.8 PNP/PCI CONFIGURATION (For Normal BIOS) 5-7

5.9 PNP/PCI CONFIGURATION (For Plug & Play BIOS) 5-8

5.10 INTEGRATED PERIPHERALS 5-10

THE OTHER SETUPS 5-11

PT-5IVL SYSTEM BOARD

TRADEMARKS

All trademarks used in this manual are the property of their respective owners.

NOTE

The "LOAD SETUP DEFAULTS" function loads the default settings directly from

BIOS default table, these default settings are the best-case values that should optimize

system performance and increase system stability . This function will be necessary

when you accept this system board, or the system CMOS data is corrupted.

By pressing "Enter" key, while "LOAD SETUP DEFAULTS" is highlighted, then

presses "Y" and "Enter" key. the SETUP default values will be loaded. (Please refer to

the Chapter 5 AWARD BIOS SETUP procedures in this maulal.)

NOTICE

Information presented in this manual has been carefully checked for reliability;

however, no responsibility is assumed for inaccuracies. The information contained in

this manual is subject to change without notice.

PT-5IVL SYSTEM BOARD INTRODUCTION

1. INTRODUCTION

1.1 SYSTEM OVERVIEW

ThePT-5IVLPentium PCI Local Bus system board is designed based on the Intel 82430VX PCIset system

chipset and Winbond I/O chipset, which built-in two channel Enhanced PIO and Bus Master PCI IDE ports, one

Floppy Disk Control port, two high speed Serial ports (UARTs) and one multimode Parallel port and also

supports IR port. It is designed to fit a high performance, Pentium 75 MHz to 200 MHz (ideally) based solution

for high-end and true GREEN-PC computer systems.

This system board supports the Peripheral Component Interconnect (PCI) Local Bus standard (PCI Spec. Rev.

2.1 compliant). It not only breaks through the I/O bottlenecks of the traditional ISA main board, but also

provides the performance needs for networking and multi-user environments.

1.2 FEATURES

The PT-5IVL system board contains the following features:

□Pentium P54C/P54CS/P54CTB/P55C, Cyrix 6x86 & AMD 5k86 based, PC/AT compatible

system board with ISA Bus and PCI Local Bus.

□Supports the most part of "586" level CPUs designed by Intel, Cyrix and AMD.

□Built-in 2 set voltage regulator circuits to support multi-spec. CPU I/O voltage (includes

Standard, VR and VRE specification) and CPU CORE voltage (+2.5V DC and +2.8V DC).

□DRAM Memory : Supports fast page mode (FPM), Extended Data Out (EDO) memory.

□Cache Memory : Supports pipelined burst SRAMs. Cache memory size up to 512KB.

□BIOS : Supports Normal and Plug & Play BIOS.

□IDE ports : Supports two channel Enhanced PIO and Bus Master PCI IDE ports, up

to Mode 4 timing, and up to 22 MBytes/s transfer rates.

□I/O ports : Supports two high speed serial ports (UARTs), One multimode parallel

port for standard (SPP), enhanced (EPP) and high speed (ECP) modes.

One Floppy Disk Control port.

□IR Port (option) : Supports IR (Infrared Rays) functions. Both HPSIR and ASKIR are

supported.

□Software : MS-DOS, WindowsNT, OS2, XENIX, UNIX, NOVELL, CAD/CAM,

compatibility Windows, Windows 95....etc.

1-1

PT-5IVL SYSTEM BOARD SPECIFICATIONS

2. SPECIFICATIONS

□CPU

Intel : Pentium processor and OverDrive processor (P54C/P54CS/P54CTB/P55C)

75/ 90/ 100/ 120/ 133/ 150/ 166 MHz and 180/ 200 MHz (ideally).

Cyrix : 6x86-P120+(100MHz)/ P133+(110MHz)/ P150+(120MHz)/ P166+(133MHz),

M2 series.

AMD : 5k86-P75(SSA/5-66)/ P75(SSA/5-75)/ P90(SSA/5-83)/ P90(SSA/5-90)/

P100(SSA/5-100)

□CPU VCC

(1). CPU I/O Voltage : Standard (+3.3V DC), VR (+3.4V DC), and VRE (+3.5V DC).

(2). CPU CORE Voltage : Egual to CPU I/O Voltage, +2.5V DC, and +2.8V DC.

□WORD SIZE

Data Path : 8-bit, 16-bit, 32-bit, 64-bit

□PC System Chipset

Intel 82430VX PCIset (82437VX, 82438VX, 82371SB)

□I/O Chipset

Winbond W83877F.

□System Clock

50/55/60/66.6 MHz adjustable.

□Memory

DRAM : Two banks, each bank could be single or double sided, 8MB up to 128 MB main

memory. Supports both fast page mode (FPM) and Extended Data Out (EDO)

memory. (Using 72-pin SIMM module x 4).

SRAM : One COAST SRAM Module slot, supports 256KB or 512KB Direct-Mapped wirte

back cache memory, using pipelined burst SRAM.

□BIOS

AWARD system BIOS. 128KB x 8 EPROM (for normal BIOS) or Flash ROM (for Plug &

Play BIOS).

□Expansion Slots

PCI Slots : 32-bit x 3 (All Master/Slave, PCI Spec. Rev. 2.1 Compliant)

ISA Slots : 16-bit x3

□IDE Ports

Two channel Enhanced PIO and Bus Master PCI IDE ports, maximum could be connected 4

IDE Hard Disks and ATAPI CD-ROM devices.

2-1

PT-5IVL SYSTEM BOARD SPECIFICATIONS

□Super I/O Ports

1. Two high speed NS16C550 compatible serial ports (UARTs).

2. One parallel port, supports SPP/EPP/ECP mode.

3. One Floppy Disk Control port.

□IR Port (option)

One HPSIR and ASKIR compatible IR transmission connector (5-pin).

□Mouse and Keyboard

Supports PS/2 mouse connector, PS/2 keyboard connector (option) and AT keyboard connector.

□DIMENSION

Width & Length : 220 mm x 220 mm.

Height : 3/4 inches with components mounted, but without expansion

boards and cables.

PCB Thickness : 4 layers, 0.05 inches normal.

Weight : 17.5 ounces.

□ENVIRONMENT

Operating Temperature : 10*C to 40*C. (50*F to 104*F)

Required Airflow : 50 linear feet per minute across CPU.

Storage Temperature : - 40*C to 70*C. (- 40*F to 158*F)

Humidity : 0 to 90% noncondensing.

Altitude : 0 to 10,000 feet.

2-2

PT-5IVL SYSTEM BOARD SYSTEM BOARD LAYOUT

3. SYSTEM BOARD LAYOUT

3.1 PT-5IVL VER. 1.2

Explanation : All connectors, jumpers and components which marks by a black point on the corner

means the pin-1 side of the connector, jumper and component.

K/B BIOS

PCI 1

PCI 2

PCI 3

SL2

CN8 POWER CON.

CN3

AT K/B

SIMM 1

Intel

82437VX

BAT 1

CPU

SYS. BIOS

CN11 IDE2

CN12 IDE1

CN9 FDC

CN7 LPT

COM B

CN6

CN1

PS/2

MS.

CN4

JP1

SPEAKER

KEYLOCK

Winbond

W83877F

SL1

SL3

JP8

RTC

MODULE

Socket 7

CN5

COM A

CN10 PBSRAM MODULE

JP7

JP11

Intel

82438VX

Intel

82371SB

SIMM 2

SIMM 3

SIMM 4

JP9

JP10

JP6

JP2

JP3

JP4

JP12

JP13

JP5

3-1

PT-5IVL SYSTEM BOARD HARDWARE SETUP

4. HARDWARE SETUP

4.1 UNPACKING

The system board package should contain the following parts :

 The PT-5IVL system board.

 OPERATION MANUAL.

 Cable set for IDE and I/O device.

4.2 HARDWARE CONFIGURATION

Before the system board is ready to operate, the hardware must be configured to allow for various functions

within the system. To configure the PT-5IVL system board is a simple task, only a few jumpers, connectors,

cables and sockets needs to be selected and installed. (For the detailed locations of each component please refer

to the "system board layout figure" which appears in page 3-1.)

4.2.1 DRAM INSTALLATION

The PT-5IVL system board will support two banks main memory (bank 0 and bank 1) on board (using four 72-

Pin SIMM socket, SIMM 1-4), each bank could be single-sided or double-sided, 8MB up to 128 MB of local

memory can be attained. Supports both standard fast page mode (FPM) and Extended Data Out (EDO) memory.

(Note that this system board doesn't support 3.3V SDRAM) The speed of FPM DRAMs must be used 70ns or

faster than 70ns, the speed of EDO DRAMs must be used 60ns or faster than 60ns.

The usable SIMM modules are : (Note : S = Single-sided , D = Double-sided)

1MBx32(36)-S ( 4MB) ,1MBx32(36)-D ( 8MB),

2MBx32(36)-S ( 8MB) ,2MBx32(36)-D (16MB),

4MBx32(36)-S (16MB) ,4MBx32(36)-D (32MB).

The following table provides the possible combinations for DRAM memory installation.

Bank 0 Bank 1 Bank 0 Bank 1

SIMM1 and SIMM2 SIMM3 and SIMM4 SIMM1 and SIMM2 SIMM3 and SIMM4

Single-sided Single-sided Double-sided Single-sided

Single-sided Double-sided Double-sided Double-sided

Bank can be populated in any order (bank 0 does not have to be populated before bank 1). Within any given

bank, the SIMMs must be the same size. Among the two banks, SIMM densities can be mixed in any order.

EDO and FPM can be mixed between SIMMs, a given SIMM must contain only one type of DRAM. When

DRAM types are mixed each SIMM runs optimized for that particular type of DRAM.

4-1

PT-5IVL SYSTEM BOARD HARDWARE SETUP

4.2.2 L2 CACHE MEMORY INSTALLATION

The PT-5IVL system board will support one bank direct-mapped second level cache, and provides either 256KB

or 512KB cache memory, using synchronous pipeline-burst SRAMs. (Note that this system board does not

support asynchronous or burst SRAMs for the L2 cache memory) Both Write Back and Write Through cache

update policy are supported.

The second level cache is supported via a COAST (Cache-On-A-STick) module, there is no jumper needed for

end-user while using L2 cache memory, just insert the COAST module into the SRAM module slot (CN10),

then the cache memory size will be detected by system BIOS automatically.

Note : The COAST modules design must comply with Intel COAST (Cache-On-A-STick)

module specification revision 2.0 or later.

4.2.3 CONNECTORS

A connector is two or more pins that are used make connections to the system standard accessories (such as

power, mouse, printer,...etc.) The following is a list of connectors on board, as well as descriptions of each

individual connector.

(A) BAT1 Non-Rechargeable battery (Using 3 Vlots Lithium battery : CR2032)

Pin # Assignment

 Battery Positive

 Ground

(B) CN1 PS/2 Mouse converted connector

Pin # Assignment Pin # Assignment Pin # Assignment

1 Mouse Data 3 Ground 5 Mouse Clock

2 No Connection 4 +5V DC

Pin # Assignment Pin # Assignment Pin # Assignment

1 Keyboard Data 3 Ground 5 Keyboard Clock

2 No Connection 4 +5V DC 6 No Connection

(D) CN3 AT Keyboard connector

Pin # Assignment Pin # Assignment Pin # Assignment

1 Keyboard Clock 3 No Connection 5 +5V DC

2 Keyboard Data 4 Ground

(E) CN4 IR (Infrared Rays) transmission connector

Pin # Assignment Pin # Assignment Pin # Assignment

1 +5V DC 3 IR Receive 5 IR Transmit

2 No Connection 4 Ground

4-2

PT-5IVL SYSTEM BOARD HARDWARE SETUP

(F) CN5 COM B (Serial Port 2) connector

COM1/2/3/4, selected by BIOS setup, using IRQ3 or 4

1 2 Pin # Assignment Pin # Assignment

○○ 1 DCD (Data Carrier Detect) 2 RD (Received Data)

○○ 3 TD (Transmit Data) 4 DTR (Data Terminal Ready)

○○ 5 Ground 6 DSR (Data Set Ready)

○○ 7 RTS (Request To Send) 8 CTS (Clear To Send)

○○ 9 RI (Ring Indicator) 10 NC (No Connection)

910

(G) CN6 COM A (Serial Port 1) connector

COM1/2/3/4, selected by BIOS setup, using IRQ4 or 3

1 2 Pin # Assignment Pin # Assignment

○○ 1 DCD (Data Carrier Detect) 2 RD (Received Data)

○○ 3 TD (Transmit Data) 4 DTR (Data Terminal Ready)

○○ 5 Ground 6 DSR (Data Set Ready)

○○ 7 RTS (Request To Send) 8 CTS (Clear To Send)

○○ 9 RI (Ring Indicator) 10 NC (No Connection)

910

(H) CN7 Parallel Port connector

(Supports SPP/EPP/ECP mode, selected by BIOS setup,using IRQ7 or IRQ5,

ECP using DMA channel 3 or 1)

114 Pin# Assignment Pin # Assignment

○○ 1 STROBE- 14 AUTO FEED-

○○ 2 Data Bit 0 15 ERROR-

○○ 3 Data Bit 1 16 INIT-

○○ 4 Data Bit 2 17 SLCT IN-

○○ 5 Data Bit 3 18 Ground

○○ 6 Data Bit 4 19 Ground

○○ 7 Data Bit 5 20 Ground

○○ 8 Data Bit 6 21 Ground

○○ 9 Data Bit 7 22 Ground

○○ 10 ACK- 23 Ground

○○ 11 BUSY 24 Ground

○○ 12 PE 25 Ground

○○ 13 SLCT 26 N.C. (No Connection)

13 26

(I) CN8 Power connector

Pin # Assignment Pin # Assignment Pin # Assignment

1 Power Good 5 Ground 9 -5V DC

2 +5V DC 6 Ground 10 +5V DC

3 +12V DC 7 Ground 11 +5V DC

4 -12V DC 8 Ground 12 +5V DC

4-3

Tabla de contenidos

Otros manuales de Placa madre de AZZA

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario