AZZA 6IFA Manual de usuario

PT-6IFA

SYSTEM BOARD

( VER. 1.x )

OPERATION MANUAL

PT-6IFA SYSTEM BOARD TABLE OF CONTENTS

TABLE OF CONTENTS

Chapter & Section Page

1. INTRODUCTION---------------------------------------------------------------------------1

1.1 SYSTEM OVERVIEW ----------------------------------------------------------------1

1.2 FEATURES ------------------------------------------------------------------------------1

2. SPECIFICATIONS -------------------------------------------------------------------------1

3. SYSTEM BOARD LAYOUT------------------------------------------------------------1

3.1 PT-6IFA VER. 1.x----------------------------------------------------------------------1

4. HARDWARE SETUP ---------------------------------------------------------------------1

4.1 UNPACKING----------------------------------------------------------------------------1

4.2 HARDWARE CONFIGURATION ------------------------------------------------1

4.2.1 DRAM INSTALLATION -------------------------------------------------------1

4.2.2 CONNECTORS--------------------------------------------------------------------3

4.2.3 JUMPERS---------------------------------------------------------------------------7

5. AWARD BIOS SETUP -------------------------------------------------------------------1

5.1 GETTING STARTED ----------------------------------------------------------------1

5.2 MAIN MENU ---------------------------------------------------------------------------1

5.3 CONTROL KEYS ---------------------------------------------------------------------2

5.4 STANDARD CMOS SETUP --------------------------------------------------------2

5.5 BIOS FEATURES SETUP ----------------------------------------------------------3

5.6 CHIPSET FEATURES SETUP ----------------------------------------------------5

5.7 POWER MANAGEMENT SETUP------------------------------------------------7

5.8 PNP/PCI CONFIGURATION-------------------------------------------------------8

5.9 INTEGRATED PERIPHERALS ---------------------------------------------------11

5.10 LOAD SETUP DEFAULTS -------------------------------------------------------12

5.11 SUPERVISOR PASSWORD / USER PASSWORD-------------------------12

5.12 IDE HDD AUTO DETECTION -------------------------------------------------13

5.13 HDD LOW LEVEL FORMAT---------------------------------------------------13

5.14 SAVE & EXIT SETUP-------------------------------------------------------------13

5.15 EXIT WITHOUT SAVING--------------------------------------------------------13

PT-6IFA SYSTEM BOARD

TRADEMARKS

All trademarks used in this manual are the property of their respective owners.

NOTE

The "LOAD SETUP DEFAULTS" function loads the default settings directly from

BIOS default table, these default settings are the best-case values that should optimize

system performance and increase system stability . This function will be necessary

when you accept this system board, or the system CMOS data is corrupted.

By pressing "Enter" key, while "LOAD SETUP DEFAULTS" is highlighted, then

presses "Y" and "Enter" key. the SETUP default values will be loaded. (Please refer to

the Chapter 5 AWARD BIOS SETUP procedures in this maulal.)

NOTICE

Information presented in this manual has been carefully checked for reliability;

however, no responsibility is assumed for inaccuracies. The information contained in

this manual is subject to change without notice.

WARRING !

The "Static Electricity" will cause damage to the components on the system board, for

this reason, please eliminate all static electricity on your body before you touch this

system board.

PT-6IFA SYSTEM BOARD INTRODUCTION

I. INTRODUCTION

A. SYSTEM OVERVIEW

ThePT-6IFAPentium Pro PCI Local Bus system board is an ATX form-factor

system board. It is designed based on the Intel 82440FX PCIset system chipset and

Winbond I/O chipset. It built-in two channel PIO and Bus Master Enhanced PCI IDE

ports, one Floppy Disk control port, two high speed Serial ports (UARTs) and one

multimode Parallel port and also supports PS/2 mouse, IR and USB ports. It is designed

to fit a high performance, Pentium Pro Processor 150 MHz up to 266 MHz based

solution for high-end and true GREEN-PC computer systems.

The Pentium Pro Processor is a 64-bit processor with RISC technology, which offers

several key features such as built-in 256KB/512KB L2 cache, 12-stage superpipeline

architecture, out of order execution .... etc, in order to optimize its capabilities and

performances, the Pentium Pro Processors require 32-bit Operating Systems (such

Windows NT and OS/2) and applications.

This system board supports the Peripheral Component Interconnect (PCI) Local Bus

standard (PCI Spec. Rev. 2.1 compliant). It not only breaks through the I/O bottlenecks

of the traditional ISA main board, but also provides the performance needs for

networking and multi-user environments.

A. FEATURES

The PT-6IFA system board contains the following features:

Supports wide range Pentium Pro family CPUs from 150 MHZ through 266

MHz , fully IBM PC/AT compatible system board with ISA Bus and PCI Local

Bus.

Built-in 3 set voltage regulator circuits to support all low-voltage components

include CPU, chipset ..., so that no VRM (Voltage Regulator Module) is needed.

DRAM Memory : Supports fast page mode (FPM), Extended Data Out (EDO)

and Burst Extended Data Out (BEDO) memory. Supports

PT-6IFA SYSTEM BOARD INTRODUCTION

ECC/Parity functions.

Cache Memory : Supports Pentium Pro CPU's built-in 256KB/512KB L2 cache.

System BIOS: Supports Plug and Play System BIOS.

IDE ports : Supports two channel PIO and Bus Master Enhanced PCI IDE

ports, up to Mode 4 timing, and up to 22 MBytes/s transfer rates.

I/O ports : Supports two high speed serial ports (UARTs), One multimode

parallel port for standard (SPP), enhanced (EPP) and high speed

(ECP) modes. One Floppy Disk Control port. And also supports

PS/2 mouse connector on board.

IR Port : Supports IR (Infrared Rays) functions. Both HPSIR and ASKIR

are supported.

USB Ports : Supports two Universal Serial Bus (USB) ports.

ACPI : Supports a part of ACPI (Advanced Configuration and Power

Interface) functions, such as "Software Power Off".

PT-6IFA SYSTEM BOARD SPECIFICATIONS

I. SPECIFICATIONS

CPU

Intel Pentium Pro processors, from 150MHz through 266 MHz

CPU VCC

Three set voltage regulator circuits, support CPU operating voltage from +2.1V DC

through +3.5V DC

WORD SIZE

Data Path : 8-bit, 16-bit, 32-bit, 64-bit

PC SYSTEM CHIPSET

Intel 82440FX PCIset (82441FX, 82442FX, 82371SB)

SUPER I/O CHIPSET

Winbond W83977F

BUS FREQUENCY

60/66.6 MHz adjustable.

MEMORY

DRAM: Four banks, each bank could be single or double sided, 8MB up to 1024

MB.

Supports fast page mode (FPM), Extended Data Out (EDO) and Burst

Extended Data Out (BEDO) memory. (Using 72-pin SIMM x6).

CACHE : Supports Intel Pentium Pro CPU's built-in 256KB/512KB L2 cache.

BIOS

AWARD Plug & Play System BIOS. (128KBx8, Flash ROM)

EXPANSION SLOTS

PCI Slots : 32-bit x 4 (All Master/Slave, PCI Spec. Rev. 2.1 Compliant)

ISA Slots : 16-bit x4 (One slot PCI/ISA shared)

PT-6IFA SYSTEM BOARD SPECIFICATIONS

IDE PORTS

Two channel PIO and Bus Master Enhanced PCI IDE ports, maximum could be

connected up to 4 IDE Hard Disk and ATAPI CD-ROM device. BIOS supports IDE

CD-ROM boot-up.

SUPER I/O PORTS

1. Two high speed NS16C550 compatible serial prots (UARTs).

2. One parallel port, supports SPP/EPP/ECP mode.

3. One Floppy Disk Control port.

IR PORT

One HPSIR and ASKIR compatible IR transmission connector (5-pin).

MOUSE AND KEYBOARD

One PS/2 mouse connector, One PS/2 keyboard connector (optional) and One AT

keyboard connector.

USB PORTS

Two Universal Serial Bus (USB) ports.

DIMENSION

Width & Length : 244 mm x 305 mm.

Height : 3/4 inches with components mounted, but without expansion

boards and cables.

PCB Thickness : 4 layers, 0.05 inches normal.

Weight : 20 ounces.

ENVIRONMENT

Operating Temperature : 10to 40. (50to 104)

Required Airflow : 50 linear feet per minute across CPU.

Storage Temperature : - 40to 70. (- 40to 158)

Humidity : 0 to 90% noncondensing.

Altitude : 0 to 10,000 feet.

PT-6IFA SYSTEM BOARD SYSTEM BOARD LAYOUT

I. SYSTEM BOARD LAYOUT

A. PT-6IFA VER. 1.x

Explanation : All connectors, jumpers and components which marks by a black point on

the corner means the pin-1 side of the connector, jumper and component.

Intel

82371SB

BAT 1

CPU

SPEAKER

KEYLOCK

Winbond

W83977F

SL4

Socket 8

JP1

82442FX

Intel

82441FX

Intel

JP5

JP4

USB2

USB1

SL3

SL2

SL1

PCI 1

PCI 2

PCI 3

PCI 4

JP3

JP2

CN5 POWER CON.

CN12

CN13

CN7 COM B CN1 COM A

CN3

PS/2

MS.

PS/2

KB.

CN2

COOLING FAN CON.

SIMM 6

SIMM 5

SIMM 4

SIMM 3

SIMM 2

SIMM 1

CN11 IR

JP11

CN4CN6 LPT

SYS. BIOS

CN9 IDE1

CN10 IDE2

CN8 FDC

JP10

JP9

JP8

JP7

JP6

1 2

PT-6IFA SYSTEM BOARD HARDWARE SETUP

I. HARDWARE SETUP

A. UNPACKING

The system board package should contain the following parts :

The PT-6IFA system board.

OPERATION MANUAL.

Cable set for IDE and I/O device.

A. HARDWARE CONFIGURATION

Before the system board is ready to operate, the hardware must be configured to allow

for various functions within the system. To configure the PT-6IFA system board is a

simple task, only a few jumpers, connectors, cables and sockets needs to be selected and

installed. (For the detailed locations of each component please refer to page 3-1 "system

board layout" figure )

1. DRAM INSTALLATION

The PT-6IFA system board will support four banks main memory on board (bank0 :

SIMM1, SIMM2. bank1 : SIMM3, SIMM4. bank2 : SIMM5, SIMM6), each bank could

be single-sided or double-sided, 8MB up to 768 MB of local memory can be attained. It

supports three types of DRAM memory either standard fast page mode (FPM),

Extended Data Out (EDO) or Burst Extended Data Out (BEDO) memory. (Both

Symmetrical and Asymmetrical DRAM addressing are supported.)

Bank can be populated in any order (bank 0 does not have to be populated before bank

1). Within any given bank, two SIMMs must be same size. Among the two banks,

SIMMs' densities could be mixed in any order. EDO, FPM and BEDO DRAMs could

be mixed between Banks, a given SIMM must contain only one type of DRAM. When

DRAM types are mixed, each SIMM runs optimized for that particular type of DRAM.

The speed of FPM DRAMs must be used 70ns or faster than 70ns, the speed of EDO

DRAMs and BEDO DRAMs must be used 60ns or faster than 60ns.

PT-6IFA SYSTEM BOARD HARDWARE SETUP

There is no jumper needed for DRAM configuration, DRAMs' type and size will be

detected by system BIOS automatically.

In DRAM memory subsystem, ECC and Parity can be checked on the DRAM interface

(Functions selected by BIOS via CMOS setup, please refer to Chapter 5, the defult

status is parity selected.) All SIMMs and DIMM must be populated with parity bit to

implement ECC or Parity functions.

ECC is an optional data integrity feature provided by the system. This feature provides

single-bit error correction, multiple-bit error detection, and detection of all errors

confined to single nibble for DRAM memory subsystem.

The SIMMs' operating voltage are :

SIMM1 - SIMM6 : + 5V DC

The usable DRAM modules are : (Note : S = Single-sided , D = Double-sided)

SIMMs : 1MBx32(36)-S ( 4MB) ,

2MBx32(36)-D ( 8MB) ,

4MBx32(36)-S ( 16MB) ,

8MBx32(36)-D ( 32MB) ,

16MBx32(36)-S ( 64MB) ,

32MBx32(36)-D (128MB) .

The following table is an example for DRAM memory installation, it contains several

modules combination, but not all combination.

Bank 0 Bank 1 Bank 2 Total

SIMM1, SIMM2 SIMM3, SIMM4 SIMM5, SIMM6 Size

4MB, 4MB 4MB, 4MB 4MB, 4MB 24 MB

8MB, 8MB 8MB, 8MB 8MB, 8MB 48 MB

16MB, 16MB 16MB, 16MB 16MB, 16MB 96 MB

32MB, 32MB 32MB, 32MB 32MB, 32MB 192 MB

64MB, 64MB 64MB, 64MB 64MB, 64MB 384 MB

128MB, 128MB 128MB, 128MB 128MB, 128MB 768 MB

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Placa madre de AZZA

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario