AWS CG-Series Manual de usuario

American Weigh Scales, Inc.

CG-50 (50x0.01g)

CG-500 (500x0.1g) User Manual

CG-Series

Digital Pocket Scale

ON/OFF

PCS TARE

MODE

CG-Series Manual

Thank you for purchasing the American Weigh

CG-Series digital scale. Please read all operating

instructions carefully before use. This electronic scale

is a precision instrument. With normal care and proper

treatment, it will provide years of reliable service.

Never load the scale with more than the maximum

capacity. Overloading will permanently damage it!

Avoid any exposure to extreme heat or cold. Your

scale works better when operated at normal room

temperature. Always allow the scale to acclimate to

normal room temperature for at least one hour before

use.

Give your scale sufcient warm up time. Usually

30-60 seconds before calibration to give the internal

components a chance to stabilize.

Keep your scale in a clean environment. Dust, dirt,

moisture, vibration, air currents and a close distance to

other electronic equipment can all cause an adverse

effect on the reliability and accuracy of your scale.

Handle with care. Gently apply all items to be weighed

onto tray top. Although this scale is designed to be

quite durable, try to avoid rough treatment as this may

permanently damage the internal sensor.

Avoid shaking, dropping or otherwise shocking the

scale. This is a precision instrument and must be

handled with extreme care.

Only operate the scale on a stable, vibration free

surface.

I. OPERATION

Place Scale on a horizontal at surface.

1. Press [ ON/OFF ] key to turn the scale on.

2. Wait until "0.0” or "0.00" is displayed.

3. Place the object(s) onto the weighing platform.

4. By pressing the [

MODE

] key, you can switch

between weighing units..

II. TARE WEIGHING

1. Turn on scale as described above.

2. Place a tray or container on the scale platform.

3. Press [ TARE

] and wait until "0.0" or "0.00" is

displayed.

4. You can now add items to the container or tray to

obtain just the weight of the contents.

III. COUNTING FEATURE

1. Turn on the scale and wait until the LCD displays

"0.0" or "0.00".

2. Place a sample quantity (25pcs, 50pcs, 75pcs,

or 100pcs) of the items you want to count onto the

platform.

3. Press and HOLD the [ PCS ] key for 2 seconds;

the LCD will display the sample quantity setting, for

example “100”.

4. Press the [ MODE ] key to select the sample

amount of the item which you placed onto the platform.

5. Press the [ PCS ] key to conrm the above

information, the LCD will now display “pcs” in the

corner to show that the scale is in counting mode.

6. Remove the sample quantity from the platform.

7. You now can place any amount of your item(s) on

the scale and the LCD will display a count.

8. You can switch between weighing mode and

counting mode by pressing [ MODE ] or [ PCS ] key

respectively.

IV. CALIBRATION

Calibration is NOT required before rst use. Only

calibrate if the scale is not weighing properly.

The CG-500 calibrates with a 500g weight*

The CG-50 calibrates with a 50g weight*

*Weights not included.

1. Turn on the scale by pressing the [ ON/OFF ] key.

2. Wait until the LCD displays “0.0” or "0.00", then

press and HOLD the [ MODE ] key for 3 seconds. The

LCD will display “CAL”. You may now release the

[ MODE ] key.

3. Press the [ MODE ] key again. The LCD will display

“CAL” followed by the required calibration weight (see

above).

4. Place the required calibration weight on the center

of the platform. The display will show “PASS” and

return to normal weighing mode.

5. Put away the calibration weight and press

[ ON/OFF ] to turn off the scale and the calibration is

nished!

V. TROUBLESHOOTING

The primary reasons for inaccuracy or malfunction

are low batteries, incorrect calibration, overload or

operating on an unstable surface. Please keep this in

mind and maintain and operate your scale properly.

This scale is a precise instrument and must be

handled with the utmost care and caution.

[Display] Elimination of errors

-----------------------------------------------

[OUT2] Recalibrate the scale (Section III).

[EEEE] You are overloading the scale. Remove the

excessive load immediately!

[un2T] Use the scale in a more stable position

Model CG-50 CG-500

Capacity 50.00g

1.764oz

250ct

771.5gn

500.0g

17.64oz

16.08ozt

321.5dwt

Resolution 0.01g

0.001oz

0.05ct

0.1gn

0.1g

0.01oz

0.01ozt

0.1dwt

Weighing Units g, oz, ct, gn g, oz, ozt, dwt

Calibration Weight (not Included) 50g 500g

Platform Dimensions (inches) 2.0 x 2.7 “ Stainless Steel

Scale Dimensions (inches) 2.2 x 3.5 x 0.9”

Power 2 x CR2032 Batteries (included)

Warranty 10 Year Warranty

Specications

Tabla de contenidos

Manuales populares de Escala de otras marcas

Gima

Gima Glass Body Fat Analyzer Manual de lista de piezas

Seca

Seca 374 Manual de usuario

TEC

TEC TEC SL59 SERIES Manual de usuario

Axis

Axis B/E Series Manual de usuario

Alecto

Alecto ACW-40 Manual de usuario

Rice Lake

Rice Lake MSI-4260 IS Manual de usuario

IKA

IKA RCT basic safety control Manual de usuario

ADE

ADE M20011 Manual de usuario

Duronic

Duronic KS3000 Manual de usuario

Digi

Digi SM-720 Manual de usuario

Cardinal

Cardinal CS Series Manual de usuario

Korona

Korona Kastella Manual de usuario

A&D

A&D FC-50Ki Manual de usuario

BDA

BDA CAMARGUE Manual de usuario

Tanita

Tanita HD-357 Manual de usuario

Leifheit

Leifheit 03173 Manual de usuario

Lumme

Lumme LU-1340 Manual de usuario

Fidelity Electronics

Fidelity Electronics G2e Manual de usuario