Avery Dennison Monarch ADTP2 EcoCut Manual de usuario

EcoCut is a trademark of Avery Dennison Corporation. Classification: Avery Dennison - Public

MONARCH®ADTP2 ECOCUT™INSTRUCTIONS

Use these instructions for the Avery Dennison® Monarch® EcoCut™ Tabletop Printer 2. EcoCut

is designed to cut through the label material, but not the liner.

EcoCut supplies do not have black marks or die cuts; set the printer’s supply type to

continuous. We recommend setting the printer’s feed mode to on-demand (peel) mode or liner

take-up (peel with liner take-up) mode.

♦The peel chute is already installed to operate in peel mode. The printer separates the label

from the liner and the liner feeds out the front of the printer.

♦Remove the peel chute to operate in peel mode with liner take-up. The printer separates the

label from the liner and the liner is collected on a take-up reel near the supply roll.

♦The feed length for each print job may vary, depending on the length set in the format or at

the printer’s menu. See “Setting Supply Options” for more information.

Information in this document supersedes information in previous versions. Check our Web site

(www.printers.averydennison.com) for any updates.

CAUTION: Do not place your fingers or any other objects into the cutter.

EcoCut Tips

♦When removing printed labels, always lift up, using the cutter cover as a guide. Do not pull

the label to remove; doing so may cause the label to tear or the printer to lose registration.

♦With 6.0 inch (or longer) labels in on-demand mode, static build-up may cause the label to

stick to the printer’s peel door. Keep a finger below the printed label and lift up to remove,

using the cutter cover as a guide.

♦Opening the printer’s peel door may cause the next label to print in on-demand mode.

♦Follow the cleaning instructions provided in this document for optimal performance.

♦The EcoCut printer is only warranted with use of Avery Dennison-approved supplies.

♦Standard die cut supplies (non-EcoCut) may be used with this printer, but you may need to

remove the cutter cartridge. See “Replacing the Cutter Cartridge” for more information.

Peel Door

2Classification: Avery Dennison - Public

Overview

1 Cutter Cover

2 Motor Cover

1 Cutter Cartridge Release 3 Cutter Cartridge (dark gray)

2 Cutter ‘Home’ Position Screw 4 Cut Depth Dial (red)

Classification: Avery Dennison - Public 3

Setting Supply Options

Set the printer for the expected operation before

loading supply/ribbon and sending print jobs.

Use the following recommendations:

Option Choices Recommendation

Supply Type E Aperture/E Die Cut/E Black Mark/ Continuous/

C Aperture/C Die Cut/C Black Mark/C Tag Edge

Continuous

Ribbon

No/Yes/High Energy

See below.

Feed Mode Continuous/On-Demand/Liner Takeup On-Demand

Cut Mode Disabled/Cut Each Tag/Cut Each Batch Cut Each Tag

Non Indexed Length 0 (value is not set)

1218 to 3248 in 203 dpi (6.0” to 16.0”)

1800 to 4800 in 300 dpi (6.0” to 16.0”)

See below.

Setting the Supply Type

Continuous is the default setting. Using any other setting causes improper operation and/or

supply faults.

Setting the Ribbon

For thermal direct supplies, no ribbon is required. For thermal transfer supplies, load a ribbon.

See “Loading a Ribbon” for more information.

Setting the Feed Mode

On-Demand is the default setting. Liner Take-up mode works with EcoCut supply. We do not

recommend continuous mode with EcoCut supply.

Setting the Cut Mode

Set how the printer cuts supply. This printer has a rotary (pizza cutter) blade. For information

about cutter maintenance, see “Cleaning Adhesive from the Supply Path.” The printer does not

have a cut button – select the appropriate cut mode for your application.

Select To

Disabled Do not cut.

Cut each tag Cut after each tag in the batch. This is the default setting.

Cut each batch Cut after the last tag in the batch (cuts in strips) not each tag. We do

not recommend this setting with EcoCut supply.

Setting the Non-Indexed Length

The supply is cut based on the feed length in the format header’s

length parameter. See “Defining the Format Header” in the Packet

Reference Manual for more information. 0 indicates the length comes

from the format header. To override the setting in the format header,

specify the non-indexed length in dots. The default is six inches.The range is 1218 to 3248 in

203 dpi (6.0” to 16.0”) or 1800 to 4800 in 300 dpi (6.0” to 16.0”).

Select To

Decrease the setting. Shortens the feed length.

Increase the setting. Increases the feed length.

Note: Press the left function button to change the amount (by 1, 10, or 100).

4Classification: Avery Dennison - Public

Loading Supply for On-Demand Mode (Peel Mode)

Set the printer for the expected operation before loading supply/ribbon and sending print jobs.

See “Setting Supply Options” for more information. Standard die cut supplies (non-EcoCut) may

be used with this printer, but you may need to remove the cutter cartridge. See “Replacing the

Cutter Cartridge” for more information.

1. Open the cover.

2. Turn the printhead latch to unlock the printhead.

3. Lift the printhead assembly until it locks into place.

4. Adjust the roll guides to fit your supply roll. The supply roll must move freely.

5. Place rolled supply on the supply holder. Continuous supply unrolls from the top.

6. Turn the supply lever to unlock the supply guides.

7. Feed the supply through the supply path and cutter. Tuck the supply under the nibs and die

cut sensor.

8. Adjust the supply guides so they

barely touch the supply. Turn the

supply lever up to lock it in place.

9. Using your fingers/thumbs, press

the peel door tabs to open the

printer’s peel door.

Printhead Latch

Printhead Assembly

Roll Guides

Supply Lever

Supply Guides

Classification: Avery Dennison - Public 5

10. Feed the supply through the opening at the bottom of the peel door.

11. Close the peel door.

12. Push the printhead release.

13. Close the printhead assembly until you hear it click into place.

14. Press FEED to position the supply under the printhead.

When removing printed labels, always lift up, using the cutter cover as a guide. Do not pull the

label to remove; doing so may cause the label to tear or the printer to lose registration.

Opening the printer’s peel door may cause the next label to print (if in on-demand mode).

Printhead Release

Liner

6Classification: Avery Dennison - Public

Removing the Peel Chute for Liner Take-Up

To use Internal Liner Take Up, remove the Peel Chute. The peel chute is installed for use

with peel mode. It guides the

liner out the bottom of the exit

door. For internal liner take up,

the liner needs to pass under

the peel roller. The peel chute

blocks this opening.

1. Using your fingers/thumbs,

press the peel door tabs to

open the printer’s peel

door.

2. Press in on the peel door

hinges to remove it. DO

NOT detach the cable.

3. Use your fingernail or flat

head screwdriver to push in

on the right side of the peel

chute. Slide that end out

and remove the chute.

4. Reattach the peel door.

Remove the Peel Chute

Pinch Roller

Classification: Avery Dennison - Public 7

Loading Supply for Internal Liner Take-up Mode

Remove the peel chute (if installed). See “Removing the Peel Chute for Liner Take-Up” for

more information.

Set the printer for the expected operation before loading supply/ribbon and sending print jobs.

See “Setting Supply Options” for more information.

Load supplies for peel mode, leaving

at least 18 inches of supply

extending past the printhead.

1. Unlock and lift the printhead

assembly until it locks into place.

2. Feed the supply under the peel

roller.

3. Remove the bail.

4. Wrap the supply around the take-

up reel in a counter-clockwise

direction.

5. Hold the supply while placing one

end of the bail in a groove in the

liner take-up reel. Gently rotate

the bail counter-clockwise until

the other end snaps into the

corresponding groove.

8Classification: Avery Dennison - Public

6. Gently slide the bail all the way onto the reel.

7. Turn the reel counter-clockwise to remove

any slack in the liner.

8. Close the printhead assembly until you hear it

click in to place.

9. Close the peel door.

10. Press FEED to position the supply under the

printhead.

When removing printed labels, always lift up,

using the cutter cover as a guide.

Removing a Full Liner Take-Up Roll

The printer alerts you when the liner take-up reel

is full. The liner take-up reel holds approximately

half of a roll of liner.

Note: The liner can be removed before the take-up reel is full.

1. Open the cover.

2. Turn the printhead latch to unlock the printhead. Lift the printhead assembly until it locks

into place.

3. Open the peel door.

4. Gently pull the liner take-up bail off the liner take-up reel.

5. Use scissors to cut the liner in front of the take-up reel.

6. Remove the liner from the take-up reel.

7. Reload supply and continue printing.

Classification: Avery Dennison - Public 9

Loading a Ribbon

Note the ribbon loading as shown.

Rotate the take-up reel until any wrinkles are past the printhead. The ribbon must be straight

and centered throughout the path.

Moving the Cutter to the Home Position

Check to see if the cutter is at the “home” position (near the printhead latch).

If it is not, there are several ways to move it

to the “home” position:

♦Close the printhead (with supply loaded)

and press FEED. The cutter moves to the

home position.

♦Using a small flat-head screwdriver, turn

the cutter home position screw clockwise

until it stops. The cutter cartridge moves

slightly as the screw turns until it stops at

home.

♦Using the printer’s control panel, press 

or . The cutter cartridge moves to the

other side.

If the cutter cannot be moved, contact

Technical Support.

Take-up Reel

Turn the screw

10 Classification: Avery Dennison - Public

Clearing a Cutter Jam

If supply jams in the cutter, the display turns red and you see error 759.

1. Press Escape to clear the error. If supply is jammed under the cutter cartridge, manually

move the cutter: Using a small flat-head screwdriver, turn the cutter cartridge’s screw

clockwise or counter-clockwise until it is away from the jammed supply.

2. Clear the supply path to remove jammed supply out of the cutter.

Caution: Do not place your fingers near the cutter’s blade.

3. Clean the supply path if you notice adhesive build-up. See “Cleaning Adhesive from the

Supply Path” for more information.

Cleaning Adhesive from the Supply Path

Clean the printer’s supply path regularly (approximately every 60,000 inches) or whenever

adhesive build-up is present. The printer prompts every 60,000 inches as a reminder to clean

the supply path. Only clean the cutter while the printer is idle (no active print jobs).

Adhesive build-up occurs on the

♦edges of the inner supply guides

♦sensors

♦peel bar/cutting anvil

♦bottom of the ribbon deflector.

♦cutter blade and depth control roller

To clean the printer’s supply path:

1. Open and remove the adhesive

remover wand (132839) from

the package. Do not touch the

foam end of the wand.

2. Use the foam end of the wand

to dampen the inner edges of

the supply guides, sensor, and

underneath the ribbon

deflector.

Adhesive build-up area

Otros manuales para Monarch ADTP2 EcoCut

Otros manuales de Etiquetadora de Avery Dennison

Avery Dennison

Avery Dennison 64-Series Manual de usuario

Avery Dennison

Avery Dennison Monarch 9860 Manual de usuario

Avery Dennison

Avery Dennison FRESHMARX 9415 Manual de usuario

Avery Dennison

Avery Dennison SNAP 500 Manual de usuario

Avery Dennison

Avery Dennison ALS 230 Manual de usuario

Avery Dennison

Avery Dennison AP3.4 Manual de usuario

Avery Dennison

Avery Dennison ALX 92x Manual de usuario

Avery Dennison

Avery Dennison Pathfinder 6057 Manual de instrucciones

Avery Dennison

Avery Dennison 64 Series Manual de usuario

Avery Dennison

Avery Dennison Monarch 1130 Manual de usuario

Avery Dennison

Avery Dennison ALX 92x Manual de usuario

Avery Dennison

Avery Dennison AP4.4 Manual de usuario

Avery Dennison

Avery Dennison ALX 92x Manual de usuario

Avery Dennison

Avery Dennison Monarch Freshmarx 9417+ Manual de servicio

Avery Dennison

Avery Dennison ALX 720 Manual de usuario

Avery Dennison

Avery Dennison Monarch 9855 Manual de usuario

Avery Dennison

Avery Dennison FRESHMARX 9415 Manual de usuario

Avery Dennison

Avery Dennison TTX 450 Guía de solución de problemas

Avery Dennison

Avery Dennison ALS 230 Manual de usuario

Avery Dennison

Avery Dennison ALS 421 Manual de usuario

Avery Dennison

Avery Dennison AP5.4 Manual de usuario

Avery Dennison

Avery Dennison TCS Guía

Avery Dennison

Avery Dennison Monarch 1130 Series Manual de usuario

Avery Dennison

Avery Dennison AP3.4 Guía de solución de problemas

Manuales populares de Etiquetadora de otras marcas

Brother

Brother P-Touch 2420PC Manual de usuario

newell

newell Dymo LabelManager 210D Manual de usuario

Brother

Brother TD-4000 Manual de usuario

U-Line

U-Line BROTHER H-8754 Manual de usuario

Tharo Systems

Tharo Systems H-435+ Manual de usuario

Brother

Brother E300 Manual de usuario

Godex

Godex RT700 SERIES Manual de usuario

ID Technology

ID Technology 252 Manual de usuario

Labelmate

Labelmate MC-11 Manual de usuario

CAB

CAB XD4M/300 Manual de usuario

Brother

Brother P-touch PT-9700PC Manual de usuario

TSC

TSC PEX1000 Series Manual de usuario

Adkins

Adkins Label Master Manual de usuario

Epson

Epson LabelWorks LW-400 Manual de usuario

Primera

Primera 510212 Manual de usuario

Brady

Brady BradyPrinter S3100 Manual de usuario

DuraLabel

DuraLabel LabPRO Manual de usuario

Novexx Solutions

Novexx Solutions XLP 604 Manual de usuario