Avery Dennison FRESHMARX 9415 Manual de usuario

Operator's

Handbook

FRESHMARX

9415™

Labeling System

28028 28028

0 0

TC9415OH Rev. AG 1/10

Each product and program carries a respective written

warranty, the only warranty on which the customer can

rely. Avery Dennison reserves the right to make changes in

the product, the programs, and their availability at any time

and without notice. Although Avery Dennison has made

every effort to provide complete and accurate information

in this manual, Avery Dennison shall not be liable for any

omissions or inaccuracies. Any update will be incorporated

in a later edition of this manual.

part of this publication may be reproduced, transmitted,

stored in a retrieval system, or translated into any

language in any form by any means, without the prior

written permission of Avery Dennison.

WARNING

This equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at his

own expense.

CANADIAN D.O.C. WARNING

This digital apparatus does not exceed the Class A limits for radio noise emissions

from digital apparatus set out in the Radio Interference Regulations of the Canadian

Department of Communications. Le présent appareil numérique n’émet pas de

bruits radioélectriques dépassant les limites applicables aux appareils numériques

de la classe A prescrites dans le Réglement sur le brouillage radioélectrique édicte

par le ministère des Communications du Canada.

Trademarks

FreshMarx® and 9415 are trademarks of Avery Dennison Retail Information

Services, LLC.

Avery Dennison® is a trademark of Avery Dennison Corp.

Avery Dennison Printer Systems Division

170 Monarch Lane

Miamisburg, OH 45342

TABLE OF CONTENTS

GETTING STARTED..........................................................1-1

Using This Manual.......................................................1-1

Audience ....................................................................1-1

Unpacking the Printer...................................................1-2

Installing the Printer.....................................................1-3

Connecting the Printer’s Power Supply ..........................1-4

Loading Labels............................................................1-5

PRINTING LABELS...........................................................2-1

About the Printer .........................................................2-2

Calibrating the Touch Screen........................................2-2

Calibrating the Touch Screen........................................2-3

Printing Freshness Labels ............................................2-4

Reprinting a Label .......................................................2-6

Printing Use First Labels ..............................................2-8

Sleep Mode.................................................................2-8

Future Upgrades..........................................................2-8

CARE & MAINTENANCE....................................................3-1

Clearing Label Jams ....................................................3-2

Cleaning the Printhead.................................................3-3

Cleaning the Touch Screen Display ...............................3-4

Cleaning the Printer.....................................................3-4

TROUBLESHOOTING........................................................4-1

Technical Support........................................................4-3

Printing a Diagnostics Label .........................................4-4

ii Operator’s Handbook

LABEL FORMATS ............................................................A-1

Format 1 .................................................................... A-1

Format 2 .................................................................... A-2

Format 3 .................................................................... A-3

Format 4 .................................................................... A-4

Format 5 .................................................................... A-5

Format 6 .................................................................... A-6

SPECIFICATIONS ............................................................B-1

Printer Specifications .................................................. B-1

Supply Specifications .................................................. B-1

Getting Started 1-1

GETTING STARTED

Use the FreshMarx® 9415™ Labeling System

for product freshness and to label inventory. This

system is available as a single or dual printer.

Information in this document supercedes information

in previous versions. Check our Web site for the latest

documentation and release information.

Using This Manual

Following is a summary of the contents of this manual:

Chapter Contents

1 Getting Started Unpacking and installing the

printer and loading supplies.

2 Printing Labels Selecting and printing freshness

labels.

3 Care &

Maintenance Clearing supply jams and

cleaning the printer.

4 Troubleshooting Common problems and their

solutions.

A Label Formats Format sizes and content fields.

B Specifications Printer and supply

specifications.

Audience

The Operator's Handbook is for the person who prints

and applies labels.

1-2 Operator’s Handbook

Unpacking the Printer

After you unpack the printer, you should have the

following:

9415 printer

power supply and cord

4 wall anchors

wall mount template

Keep all packaging material in case you need to move

or return the printer.

Caution: Do not touch the electrical connectors

while setting up the printer. Static

electricity can damage or destroy the

electronic components.

Getting Started 1-3

Installing the Printer

To install the printer on the wall:

1. Select a suitable location for the printer on a wall.

2. Tape the wall mount template to the wall in the

selected location.

Caution: The template must be level or the printer

will not install correctly.

3. Install the four wall anchors according to the four

outside holes indicated on the template.

4. Remove the template.

5. Lower the supply door on the printer so you can

see the mounting holes on the back of the printer.

6. Attach the printer to the wall anchors using the

corresponding holes on the back of the printer.

7. Press down firmly on the printer to lock it in place.

8. Close the supply door.

Mounting holes in back of printer

1-4 Operator’s Handbook

Connecting the Printer’s Power Supply

To connect the power supply to the printer:

1. Turn off the printer. Press the power switch on

the side of the printer to the off (O) position.

2. Place the power supply in a suitable location,

preferably on a table, near an electrical outlet.

3. Plug the three-hole end of the AC adapter cable

into the three-pronged outlet in the printer’s power

supply.

4. Plug the L-shaped end of the power supply cable

into the socket on the side of the printer.

5. Plug the three-pronged end of the AC adapter

cord into a grounded electrical outlet.

Warning: The printer and power supply should

never be operated in a location where

either one can get wet. Personal injury

could result.

Power socket

L-Shaped

Connector

Getting Started 1-5

Loading Labels

Dual printer: Printer 1 is located on the left and

Printer 2 is located on the right. Printer 1 is the

default printer for all categories and formats.

Single printer: Printer 1 (located on the left) is the

only available printer. There is no option to assign a

format to a printer.

The first time you load the printer after receiving it you

must remove and discard the thermal paper from the

printer slots.

1. Turn on the printer. Press the power switch on the

side of the printer to the on (I) position.

2. Press to remove the thermal paper from the

printer, if necessary.

3. Remove and discard the tape from a new roll of

labels.

4. Lower the supply door.

5. Slide a roll of labels onto the supply holder.

If necessary, adjust the supply holder guide so it

touches the roll.

6. Feed the labels, printing side up, into the supply

slots in the supply door.

Note: Make sure no label adhesive is exposed when

loading labels. This causes jams.

1-6 Operator’s Handbook

7. Make sure the supply clip is in the correct position

to touch the edge of the supply. This clip guides

the labels through the supply slot so they do not

shift while printing.

8. Close the supply door.

The printer calibrates the labels automatically.

Supply Holder

Guide

Dual printer shown

Supply clip

Printer 2

Printer 1

Supply slot

Otros manuales para FRESHMARX 9415

Tabla de contenidos

Otros manuales de Etiquetadora de Avery Dennison

Avery Dennison

Avery Dennison AP4.4 Manual de usuario

Avery Dennison

Avery Dennison AP7.t Manual de instrucciones

Avery Dennison

Avery Dennison MONARCH 9417+ Manual de usuario

Avery Dennison

Avery Dennison ALS 204 Manual de usuario

Avery Dennison

Avery Dennison ALX 92x Manual de usuario

Avery Dennison

Avery Dennison ALX 720 Manual de usuario

Avery Dennison

Avery Dennison ALS 204 Manual de usuario

Avery Dennison

Avery Dennison FRESHMARX 9415 Manual de servicio

Avery Dennison

Avery Dennison ALS 330/430 Manual de usuario

Avery Dennison

Avery Dennison Monarch 1130 Series Manual de usuario

Avery Dennison

Avery Dennison S 105 Manual de usuario

Avery Dennison

Avery Dennison ALX 92x Manual de usuario

Avery Dennison

Avery Dennison Labelers 1103-1110 Manual de usuario

Avery Dennison

Avery Dennison Monarch Freshmarx 9417+ Manual de servicio

Avery Dennison

Avery Dennison Monarch ADTP2 EcoCut Manual de usuario

Avery Dennison

Avery Dennison AP5.4 Guía de solución de problemas

Avery Dennison

Avery Dennison Monarch 9860 Manual de usuario

Avery Dennison

Avery Dennison 64 Series Manual de usuario

Avery Dennison

Avery Dennison Monarch 9855 Manual de usuario

Avery Dennison

Avery Dennison Pathfinder 6057 Manual de instrucciones

Avery Dennison

Avery Dennison 221 RH Manual de usuario

Avery Dennison

Avery Dennison 64-Series Manual de usuario

Avery Dennison

Avery Dennison SNAP 500 Manual de usuario

Avery Dennison

Avery Dennison Monarch 1130 Manual de usuario

Manuales populares de Etiquetadora de otras marcas

Brother

Brother P-Touch 2420PC Manual de usuario

newell

newell Dymo LabelManager 210D Manual de usuario

Brother

Brother TD-4000 Manual de usuario

U-Line

U-Line BROTHER H-8754 Manual de usuario

Tharo Systems

Tharo Systems H-435+ Manual de usuario

Brother

Brother E300 Manual de usuario

Godex

Godex RT700 SERIES Manual de usuario

ID Technology

ID Technology 252 Manual de usuario

Labelmate

Labelmate MC-11 Manual de usuario

CAB

CAB XD4M/300 Manual de usuario

Brother

Brother P-touch PT-9700PC Manual de usuario

TSC

TSC PEX1000 Series Manual de usuario

Adkins

Adkins Label Master Manual de usuario

Epson

Epson LabelWorks LW-400 Manual de usuario

Primera

Primera 510212 Manual de usuario

Brady

Brady BradyPrinter S3100 Manual de usuario

DuraLabel

DuraLabel LabPRO Manual de usuario

Novexx Solutions

Novexx Solutions XLP 604 Manual de usuario