Audio Authority 1394A Manual de usuario
User Manual
Model 1394A, and 1398A
HDMI Distribution Ampli ers
CLUX-14S(TVONE)
2008.03.03
1:1
陳秋文
膜面向上
MRN-1TDA654-2
MMC-1TDA654-U
MRN-1TDA654-2
HDMI / DVI HDCP SYNC 4 3 2 1 POWER
v1.3
MMC-1TDA654-U
HDMI IN HDMI OUT1 2 3 4
EDID
INT AUTO 5V DC
DATE LTR REVISION RECORD AUTH DR CK
Model 1394A 1x4 Distribution Ampli er
Model 1394A 1x4 Distribution Ampli er
v 1.3
3/13/08
3/13/08
A
Release
Release
DAF
DAF
1394A
1394A Front and Back Artwork
3/13/08
NA
1/1
DAF
A
2
Table Of Contents
1.0
Introduction
. . . . . . . . . . . . . . . . . . . . .
. .
3
2.0
Getting the Best Results
. . . . . . . . . . . . . . . . .
5
3.0
Checking Package Contents
. . . . . . . . . . . . . . .
5
4.0
Connecting The Hardware
. . . . . . . . . . . . . . .
6
5.0
Operating The Unit
. . . . . . . . . . . . . . . . . . .
7
6.0
Troubleshooting
. . . . . . . . . . . . . . . . . . . . .
9
7.0
Limited Warranty
. . . . . . . . . . . . . . . . . . .
10
8.0
Regulatory Compliance
. . . . . . . . . . . . . . . .
11
9.0
Contact Information
. . . . . . . . . . . . . . . . . .
11
Liability Statement
Every effort has been made to ensure that this product is free of defects. Audio Authority
cannot be held liable for the use of this hardware or any direct or indirect consequential
damages arising from its use. It is the responsibility of the user of the hardware to check
that it is suitable for his/her requirements and that it is installed correctly. All rights reserved.
No parts of this manual may be reproduced or transmitted by any form or means electronic
or mechanical, including photocopying, recording or by any information storage or retrieval
system without the written consent of the publisher.
Audio Authority reserves the right to revise any of its hardware and software following its
policy to modify and/or improve its products where necessary or desirable. This statement
does not affect the legal rights of the user in any way.
Audio Authority and the Double-A Symbol are registered trademarks of Audio Authority
Corp. Copyright April, 2006, all rights reserved. All third party trademarks and copyrights
are recognized.
HDMI, the HDMI logo and High-De nition Multimedia Interface are trademarks or registered
trademarks of HDMI Licensing LLC.
3
1.0 INTRODUCTION
Thanks for purchasing this Model 1394A or 1398A distribution ampli er
from Audio Authority. These distribution ampli ers are designed to split
an HDMI signal from one source to multiple HDMI displays without signal
degradation or loss of encryption. The 1394A and 1398A are HDCP
1.1 compliant, and HDMI v1.3 compliant, supporting deep color video
and Dolby TureHD and DTS-HD Master Audio. Ultra high bandwidth,
equalized inputs, and ampli ed outputs insure a awless installation
even with long cable runs. Audio Authority also offers an extensive line of
audio and video switchers, converters and distribution amps available for
purchase online at www.audioauthority.com.
1.1 FEATURES
•
Distributes one HDMI source signal to multiple destinations
•
Equalizer/extender circuitry allows up to 30m (100’) input cable length
•
Ampli ed outputs allow up to 30m (100’) cable runs to HDMI sink
•
Outputs may be cascaded to create an extensive distribution network
•
Supports 10/12 bit color depth display
•
Supports 480i, 480p, 720p, 1080i, 1080p and many PC resolutions
•
Supports Dolby Digital +, Dolby® Digital TrueHD and DTS-HD Audio
•
HDMI version 1.3 compliant, HDCP 1.1 compliant
•
Individual HDCP keys allow each output to handshake with a display
sink independently
•
Originates EDID for the source or can re-transmit the EDID from a
downstream HDMI sink
•
Supports automatic discovery of display EDID
•
Accepts locking HDMI cables
4
1.2 SPECIFICATIONS
Compliance
HDMI
1.3 compliant
HDCP
1.1 compliant
Video Inputs
HDMI (all models)
1x via HDMI connector
Video Output
1394 HDMI
4x via HDMI connector
1398 HDMI
8x via HDMI connector
Audio Output
HDMI
HD-Audio, including Dolby® TrueHD & DTS-HD
Audio bandwidth
20Hz to 20 KHz
General
Frequency bandwidth
2.25Gbps (single link)
Color depth
10/12 bit color depth display
Supported PC/DVI resolutions
Up to 1920x1200
Supported HDTV formats
480i, 480p, 576i, 576p, 720p, 1080i and 1080p
Compliance
HDMI V1.3, HDCP V1.1, DVI V1.0
Signal equalization
Internal
Maximum Distances
Source to DA
20m (60’) for 1080p/8-bit, 15m (45’) for 1080p/12-bit
DA to display
15m (45’) for 1080p/8-bit, 10m (30’) for 1080p/12-bit
Warranty
Limited warranty
2 years parts and labor
Mechanical
1394 (H-W-D)
1.6x8.6x5.8” (41.5x218x147mm)
1398 (H-W-D)
1.75”19.0”x6.3” (44x436x160mm)
1394 weight
1.88lbs (0.85kg) net
1398 weight
4.4 lbs (2kg) net
Environmental
Operating temperature
0° to +50°C (+32° to +122°F)
Operating humidity
10% to 90%, non-condensing
Storage temperature
0° to +50°C (+32° to +122°F)
Storage humidity
10% to 90%, non-condensing
Power Requirement
External power supply
5VDC@2A (1394), 5VDC@5A (1398)
Regulatory Approvals
HDMI DAs
FCC, CE, RoHS
Power supply
UL, CUL, CE, PSE, GS, RoHS
Accessories Included
AC power adapter
USA
Instruction manual
5
2.0 GETTING THE BEST RESULTS
Many factors in uence the quality and reliability of HDMI signal
distribution installations. The following are the main factors to consider,
and basic precautions that will ensure the best possible performance.
•
Output display device.
The quality of the output signal depends
largely upon the type and quality of the HDMI display device used.
For instance, some televisions just look better than others.
•
Distance between the DA sources and the display.
Long distances
are possible, but premium quality cables and advanced HDMI
extenders with DDC correction may be necessary for the longest runs.
•
Input/output connection cables.
Low quality cables are susceptible
to interference. They degrade signal quality due to poor conductor
matching and can cause elevated noise levels. Cables should be of
the best quality.
•
Interference from nearby electrical devices
can have an adverse
effect on signal quality. For example, an older computer monitor often
emits very high electromagnetic elds that can interfere with the
performance of video equipment in its proximity.
2.1 Resolution Tracking
Since HDTV can be output from the source at any of several different
resolutions, the 1390 series DA can sense and accept any standard
resolution; however, on the outputs, the DA must sense the resolution
capabilities of all of the display devices connected to it and then set
the resolution of all outputs to the resolution of the display having the
lowest
resolution response characteristics. This behavior insures that all
lowest resolution response characteristics. This behavior insures that all lowest
displays can produce a picture. It is best to use display devices having
the same maximum resolution; just one display with lower resolution
capabilities causes all of the other displays connected to the DA to
receive that same low resolution.
3.0 CHECKING PACKAGE CONTENTS
Before attempting to use this DA, please check the packaging and make
certain the following items are contained in the shipping carton:
• HDMI Distribution Ampli er
• 5 VDC Power Adapter
• User Manual
N
ote: please keep the original packing material in case the unit ever needs to be
returned. If you nd any items are missing, contact Audio Authority immediately. Have
the model number and invoice available for reference when you call.
6
4.0 CONNECTING THE HARDWARE
Please study the front and rear panel drawings and become familiar with
the signal input, outputs and power inputs.
The 1394 and 1398 are functionally identical with the exception of the
number of outputs. Both have a single HDMI input and a 5 VDC power
input socket. LEDs on the front panel indicate when the DA is furnishing
a signal to an HDMI compliant device.
•
Connect an HDMI approved cable from the HDMI source to the input
of the DA. Cable length can be up to 30 meters – preferably shorter.
•
Connect the outputs of the DA to their destination devices using HDMI
approved cables no more than 30 meters long.
•
Connect the power adapter to the AC source and then to the DA.
•
Turn on the HDMI source and HDMI destination devices and observe
the source signal on the inputs of all of the destination devices. The
DA’s front panel LEDs will light indicating which outputs are active.
•
Make certain that the HDMI cables are securely plugged into the
source and display devices as well as the HDMI DA. Always use high
quality cables, and the shortest length possible, for best results.
The unit begins to function as soon as the AC adapter is connected to
the unit and AC power. There is no power switch. There are no other
operator interventions required with the possible exception of the EDID
jumper (see 5.0 Operating the Unit).
4.1 Using the Positive Cable Securing Feature
If HDMI cables are used that are equipped with locking type connectors,
remove the Philips head screws from the rear of the unit just above the
HDMI connectors and replace them with the hex nut/screws included
with the accessory pack. After screwing these into the threaded holes
vacated by the Philips head screws, the hex nut provides a threaded
receptacle for the screw that is part of the locking HDMI connector on the
cable. Plug in the cable’s locking HDMI connector and secure it to the
unit with its integral screw.
4.2 Optional Rack Mount Kit
The distribution ampli ers can be mounted in a standard 19” equipment
rack. Attach the furnished rack ears the sides of the unit and then attach
the unit to the 19” rack using the furnished hardware. To mount the 1394
DA in a rack, the rack mount kit must be used.
7
Model 1394A HDMI Distribution Ampli er, rear view. Model 1398A is similar.
CLUX-14S(TVONE)
2008.03.03
1:1
陳秋文
膜面向上
MRN-1TDA654-2
MMC-1TDA654-U
MRN-1TDA654-2
HDMI / DVI HDCP SYNC 4 3 2 1 POWER
v1.3
MMC-1TDA654-U
HDMI IN HDMI OUT1 2 3 4
EDID
INT AUTO 5V DC
DATE LTR REVISION RECORD AUTH DR CK
Model 1394A 1x4 Distribution Ampli er
Model 1394A 1x4 Distribution Ampli er
v 1.3
3/13/08
3/13/08
A
Release
Release
DAF
DAF
1394A
1394A Front and Back Artwork
3/13/08
NA
1/1
DAF
A
Model 1394A HDMI Distribution Ampli er, front view. Model 1398A is similar.
CLUX-14S(TVONE)
2008.03.03
1:1
陳秋文
膜面向上
MRN-1TDA654-2
MMC-1TDA654-U
MRN-1TDA654-2
HDMI / DVI HDCP SYNC 4 3 2 1 POWER
v1.3
MMC-1TDA654-U
HDMI IN HDMI OUT1 2 3 4
EDID
INT AUTO 5V DC
DATE LTR REVISION RECORD AUTH DR CK
Model 1394A 1x4 Distribution Ampli er
Model 1394A 1x4 Distribution Ampli er
v 1.3
3/13/08
3/13/08
A
Release
Release
DAF
DAF
1394A
1394A Front and Back Artwork
3/13/08
NA
1/1
DAF
A
5.0 OPERATING THE UNIT
*Note: Proper operation of HDMI distribution ampli ers depends on the
use of high quality HDMI cables that provide low loss, high bandwidth
signal handling. The distance speci cation cannot be guaranteed unless
cables used throughout the system meet these high standards.
5.1 Noti cation LEDs
There are LEDs for each output which show whether or not the output
has successfully made a connection with the destination device. In
addition to these, four more LEDs provide the following information:
•
HDMI / DVI
LED shows whether an HDMI or DVI signal is being
received.
•
HDCP
LED shows if the signal is encoded with HDCP (High-bandwidth
Digital Content Protection) signals.
•
SYNC
LED shows if the HDMI signal has synchronized.
•
POWER
LED shows the unit is receiving power.
HDMI / DVI HDCP SYNC OUTPUT POSITIONS POWER
EDID SWITCH HDMI INPUT HDMI OUTPUTS
POWER JACK
8
5.2 EDID Jumper Operation
On the rear of the unit you’ll nd an EDID* Jumper. The default factory
setting for the EDID Control Jumper is
AUTO
and you should leave it as
it is if the display is operating properly.
The EDID jumper controls whether the DA determines the connected
devices’ EDID information automatically or uses an internal information
table. Switch to
INT
(Internal) to use the built-in EDID information table if
communication problems occur.
When the EDID control jumper is in AUTO position, the unit detects the
rst destination HDMI device’s EDID and records the value in the DA. If
the rst detected output device is DVI, it passes on to the next device in
sequence until the rst HDMI compliant device has been detected.
If the DA cannot reliably determine the destination device’s EDID through
the information exchange, switching to the internal table (INT) allows the
DA to run through a range of pre-de ned resolutions and refresh rates so
that a reliable connection can be made.
* The Extended Display Identi cation Data (EDID) is a data structure
provided by a display to describe its capabilities. It’s what enables the
DA to know what kind of video display is connected to the unit. EDID
is de ned by a standard published by the Video Electronics Standards
Association (VESA). The EDID includes manufacturer name, product
type, phosphor or lter type, timings supported by the display, display
size, luminance data and (for digital displays only) pixel mapping data.
9
6.0 TROUBLESHOOTING
•
For 1080p resolution, rst make certain that the input cable is as short
as possible and none of the output cables are more than 30 meters
long. HDMI cable design and quality are extremely important in long
cable runs where capacitance can severely effect performance. Our
1391A Extender/DDC Corrector may be a necessary accessory to use
in extreme length applications.
•
Make certain that the Distribution Ampli er is receiving power by
looking at the power LED. It should be illuminated and not ickering
on and off. Intermittent operation generally means a problem with the
DC power adapter or low AC voltage being applied to the DC adapter’s
input.
•
If you still experience problems using the distribution ampli er, you
should attempt to determine what is wrong by rst attaching the source
device directly to each of the destination devices in turn using the
same cables you are using with the expanded system. This is a way of
determining if the problem is due to bad cables or a problem with the
other devices. If you are unable to obtain a signal using this simpli ed
path, suspect the cables, the source device or the destination device.
•
Remember that HDMI devices communicate with one another so the
source device and all destination devices must be fully HDMI capable.
In addition, HDCP encryption requires processing dependent on the
equipment you have connected to both the source and destination
devices.
If the problem still persists after trying the above suggestions, contact the
Audio Authority Technical Service department via email: support@audioa
uthority.com, or call 800-322-8346 or 859-233-4599.
10
7.0 LIMITED WARRANTY
Should any consumer use product from Audio Authority fail due to
defects in materials or workmanship within one year from the date of
the original sale to the end-user, Audio Authority guarantees that we
will replace the defective product at no cost. Freight charges for the
replacement unit will be paid by Audio Authority (Ground service only).
A copy of the invoice showing the item number and date of purchase
(proof-of-purchase) must be submitted with the defective unit to
constitute a valid in-warranty claim.
Units that fail after the warranty period has expired may be returned to
the factory for repair at a nominal charge, if not damaged beyond the
point of repair. All freight charges for out-of-warranty returns for repair
are the responsibility of the customer. Units returned for repair must
have a Return Authorization Number assigned by the factory.
This is a limited warranty and is not applicable for products which, in our
opinion, have been damaged, altered, abused, misused, or improperly
installed. Audio Authority makes no other warranties either expressed
or implied, including limitation warranties as to merchantability or tness
for a particular purpose. Additionally, there are no allowances or credits
available for service work or installation performed in the eld by the end
user.
Warranty Service Procedures
If you suspect a product defect, contact Audio Authority’s Technical
Service Department at 800-322-8346 or 859-233-4599 for assistance
in verifying the problem. If a defect or potential defect is suspected, a
replacement unit will be shipped immediately on a defect-exchange basis
and a Return Authorization Number will be issued for the return of the
defective product. Replacement units are sent out at the Manufacturer’s
Suggested Retail Price which is debited to the Customer’s Credit
Card at the time of shipment. Once we receive the defective unit
back at the factory, it will be evaluated under the conditions of this
warranty and if found to be in-warranty, a full credit will be issued to the
Customer’s Credit Card. Return freight charges for the defective unit
are the customer’s responsibility. Please contact our Technical Service
Department for complete details concerning all in and out of warranty
service matters.
We appreciate your con dence in our products and services and will
always strive to meet or exceed your needs.
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Amplificador de Audio Authority
Audio Authority
Audio Authority 1710B Manual de usuario
Audio Authority
Audio Authority 1354 Manual de usuario
Audio Authority
Audio Authority SonaFlex SF-16M Manual de usuario
Audio Authority
Audio Authority SF-16M Instrucciones de funcionamiento
Audio Authority
Audio Authority 1392A Manual de usuario
Audio Authority
Audio Authority HDMI 1398B Manual de usuario
Audio Authority
Audio Authority 1392 Manual de usuario
Audio Authority
Audio Authority 1805 Manual de usuario
Audio Authority
Audio Authority High Definition Cat 5 Matrix AVX-562 Manual de usuario
Audio Authority
Audio Authority 1185ci Manual de usuario
Audio Authority
Audio Authority ADX-1616 Manual
Audio Authority
Audio Authority 1398D Manual de usuario
Audio Authority
Audio Authority 1710 Manual de usuario
Audio Authority
Audio Authority 1805 Manual de usuario
Audio Authority
Audio Authority 1398D Manual de usuario
Audio Authority
Audio Authority 1714 Manual de usuario
Audio Authority
Audio Authority 1374A Manual de usuario
Audio Authority
Audio Authority 985DTV Instrucciones de funcionamiento
Audio Authority
Audio Authority 1816 Manual de usuario
Audio Authority
Audio Authority Sona Flex SF-16B Instrucciones de funcionamiento
