ATOMSTACK X20 Pro Manual de usuario
ATOMSTACK Laser E n g raver User Manual
F03-0048-0AA2 Version: A
Note: The picture is for reference only, the actual product shall prevail.
For more information, please scan the QR code.
English
Deutsche
Français
Italiano
Español
Before using the laser engraving, please read this safety guide carefully, it mentions situations that require special attention and
includes warnings of unsafe practices that can cause damage to your property or even endanger your personal safety.
1. The product belongs to Class 4 laser products, the laser system itself must meet the requirements of IEC 60825-1 latest version,
otherwise the product is prohibited to be used.
2. Our laser engraver has a protective case that prevents people from laser radiation when in place.
3. If a protective housing is equipped with an access panel which provides "walk-in" access then:
a)means shall be provided so that any person inside the protective housing can prevent activation of a laser hazard that is equivalent to
Class 3B or Class 4.
b）There is a warning device so as to provide adequate warning of emission of laser radiation equivalent to Class 3R in the wavelength
range below 400 nm and above 700 nm, or of laser radiation equivalent to Class 3B or Class 4 to any person who might be within the
protective housing.
c)Where “walk-in” access during operation is intended or reasonably foreseeable, emission of laser radiation that is equivalent to Class
3B or Class 4 while someone is present inside the protective housing of a Class 1, Class 2, or Class 3R product shall be prevented by
engineering means.
Note:Methods to prevent human from radiation when persons are inside the protective housing can include pressure sensitive floor mats,
infrared detectors, etc.
Part 1: Security Statement Before Installation
4. The laser itself has a protective cover, the protective cover is fastened by screws. When the laser is installed on the laser engraver, the
protective cover should be checked to be reliably locked, and can not be removed in the energized state.
5. The housing of the laser engraver have an interlock function. When the housing is opened or removed, the laser can be automatically
turned off.
6. The laser engraver have an emergency stop button, which can immediately stop the output of the laser when pressed under
unexpected circumstances.
7. The laser engraver have a reset button, which can resume work under the condition of confirming safety after lifting the interlock or
emergency stop.
8. Laser engraver use physical keys, dongle, password system and other ways to manage and control, and prevent personnel without
safety training from operating such equipment.
9. Set a warning mark on any window or channel that can actively observe or passively receive laser radiation on the laser engraving
machine.
10. If the laser burns the skin or eyes, please go to a nearby hospital for examination and treatment immediately.
Laser light can hurt the human eyes and skin. Do not expose the eye or skin to laser light directly. This Laser product has an optical lens
and emits a collimated laser beam. The light emitted by the product, whether it is direct or reflected, is very harmful. Because it can
propagate a long distance while maintaining high optical density. When handling the product,you must wear appropriate
goggles(OD5+) to protect eyes from laser light including reflected and stray light. The reflected and stray light spilling into an
unintended area should be attenuated and/or absorbed.
2.1 Laser safety
We installed a laser shield on the laser, the shield can largely filter out the diffuse reflection of the laser spot. However, when using laser
engraving machine, it is recommended that you should wear laser protective glasses. Avoid skin exposure to type 4 laser beams,
especially at the closed distance. Teenagers must have parental supervision in the process of using it. Do not touch the laser engraving
module when the machine is activated.
2.2 Fire safety
Because cutting burns off the substrate, a high-intensity laser beam generates extremely high temperatures and a lot of heat.Certain
materials can catch fire during cutting, creating gases and fumes inside the equipment. A small flame usually appears here when a laser
beam hits the material. It will move with the laser and will not stay lit when the laser passes by. Do not leave the machine unattended
during the engraving process. After use, be sure to clean up the debris, debris and flammable materials in the laser cutting machine.
Always keep an available fire extinguisher nearby to ensure safety. When laser engraving machines are used, smoke, vapour, particles,
and potentially highly toxic materials (plastics and other combustible materials) are produced from the material. These fumes or air
pollutants can be hazardous to health.
Part 2：User Security Statement
2.3 Material safety
Do not engrave materials with unknown properties. Materials Recommended: wood, bamboo, leather, plastic, fabric, paper, opaque
acrylic, glass, metal. Materials not recommended: precious stones, transparent materials, any reflective material, including reflective
metal etc.
2.4 Use Safety
Use the engraver only in horizontal position and ensure that it has been securely fixed to prevent fires caused by accidental shifting or
dropping from the workbench during work. It is forbidden to point the laser to people, animals or any combustible object, whether it is
in working condition or not.
2.5 Power safety
Topreventaccidentaldisasterssuchasfireandelectricshock,thelaserengraverprovidesapoweradapterwitha groundwire. When
using the laser engraving machine, insert the power plug into a power socket with a ground wire withaground wirewhenusing
theLaserEngraver.
2.6 Environment safety
When installing engraving and cutting equipment, please make sure that the workplace must be cleaned up, and there should be no
flammable and explosive materials around the equipment. A metal plate must be placed under the bottom when engraving or cutting.
Part 3: Disclaimer and warning
Thisproductisnotatoyandisnotsuitableforpeopleunder15.Donotallowchildrentotouchthelaser
module.Pleasebecarefulwhenoperatinginsceneswithchildren.
This product is a laser module. Please scan the QR code on the cover to get the complete "User Manual" and the latest instructions and
warnings. Shenzhen AtomStack Technology Co., Ltd. (Atomstack) reserves the right to update this disclaimer and safe operation guide.
Pleasebesuretoreadthisdocumentcarefullybeforeusingtheproducttounderstandyourlegalrights,responsibilitiesandsafetyinstructi
ons;Otherwise,itmaybringpropertyloss,safetyaccidentandhiddendangerofpersonalsafety.Onceyouusethisproduct,youshallbed
eemedtohaveunderstood,andacceptedalltermsandcontentsofthisdocument.Userundertakestoberesponsibleforhisorheraction
sandallconsequencesarisingtherefrom.UseragreestousetheProductonlyforlegitimatepurposesandagreestotheentiretermsandc
ontentsofthisdocumentandanyrelevantpoliciesorguidelinesthatAtomStackmayestablish.
You understand and agree that Atomstack may not be able to provide you with the cause of the damage or accident and provide you with
AtomStack's after-sale service unless you provide the original engraving or cutting files, engraving software configuration parameters used,
operating system information, video of the engraving or cutting process, and operational steps prior to the occurrence of a problem or
failure.
Atomstackisnotliableforanyandalllossesarisingfromtheuser'sfailuretousetheproductinaccordancewiththismanual,Without the
guidance of the company's technical personnel, users are prohibited from disassembling the machine by themselves. If this behavior occurs,
the loss caused by the user shall be borne by the user.
Atomstackhastheultimaterighttointerpretthedocument,subjecttolegalcompliance.Atomstackreservestherighttoupdate,modify,or
terminatetheTermswithoutpriornotice.
S t e p 1
P a r t 4 : I n s t a l l a t i o n S t e p s
Logo side up
Tabel side up
Large hole outwarderSilkscreen tick marks outward
S t e p 2
The guide rail passes through the middle of the 3 rollers.
Use a wrench to turn the eccentric nut, to loose the
distance between the upper and lower guide wheels
appropriately, then tight the eccentric nuts.
This screw is different
TIPS：
How to determine the tightness of
eccentric nuts?
Under the condition of ensuring that
the bracket does not shake, you can lift
one end of the machine to an angle of
45 degrees with the horizontal plane,
and release the X-axis or Y-axis bracket
from a high place. If the bracket can
slide at a constant speed to the end, the
tightness is suitable.
After the assembly is completed, if you
find that the four feet are not level,
please slightly loosen the 8 screws in
the first step, and after the four feet are
leveled, tighten the screws again.
45°
TIPS：
Place the screws, but do not
tighten them.
Then tighten the screws
diagonally.
S t e p 3
S t e p 4
Tighten the T nut and cut off the excess belt,assembly the end cap.
TIPS:
The installation of the Y-axis synchronous belt can refer to
the installed synchronous belt on the X-axis assembly.
Determine whether the belt is tight enough:
Use your finger to press the position shown in the picture
on the far left, if the belt is elastic, it is tight enough. If the
deformation is large, loosen the T-Nut on one end, tighten
the belt, and then tighten the T-Nut.
Press
Connect the display
Assembly Laser
Placing focus pad
Insert the five wire terminals
as shown,
Tie the wires to the machine
with cable ties.
Shield（red part）
Air guide hood
（white part）
S t e p 5
Place the cutting pad under the engraved/cut object,
The cutting pad should be placed to coincide as much as possible with
the working area.
Cutting Pad
The laser power of this machine is very high, if you need to cut wood and other flammable
materials with a power of more than 70%, please ensure someone is watching the machine in case
of the flammable materials catches fire.
A lot of smoke is generated in engraving or cutting wood and other
objects, be aware of cleaning the air guide hood and anti-skid cover,
since there may be a lot of dust accumulation on it, especially working
with more than 50% of the laser power.
Remove the shield if you could, or turn on the air assit while machine
working, all of which would significantly reduce dust accumulation.
Two ways to use the focus pad
object
Shield focus pad (Horizontal)
object
focus pad (Vertical)
With a shield Without a shield
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Grabador de ATOMSTACK
ATOMSTACK
ATOMSTACK A6 PRO Manual de usuario
ATOMSTACK
ATOMSTACK Befon A5 Pro Plus Manual de usuario
ATOMSTACK
ATOMSTACK A5 10W Manual de usuario
ATOMSTACK
ATOMSTACK X7 Pro Series Manual de usuario
ATOMSTACK
ATOMSTACK A5 M50 Pro Manual de usuario
ATOMSTACK
ATOMSTACK P7 Series Manual de usuario
ATOMSTACK
ATOMSTACK A5 Manual de usuario
ATOMSTACK
ATOMSTACK MAKER AC1 Manual de usuario
ATOMSTACK
ATOMSTACK M100 Manual de usuario
ATOMSTACK
ATOMSTACK A 5 Pro Manual de usuario
