ATOMSTACK P7 Series Manual de usuario
ATOMSTACK P7 Series Laser EngraverInstallation Manual
The picture is for reference only, the actual product shall prevail
English
Deutsche
Français
Version：V1.0
Before Using the laser engraving, please read this safety guide carefully, it mentions situations that require special attention and includes
warnings of unsafe practices that can cause damage to your property or even endanger your personal safety.
1. The product belongs to Class 4 laser products, the laser system itself must meet the requirements of IEC 60825-1 latest version, otherwise
the product is prohibited to be used.
2. Our laser engraver have a protective housing which, when in place, prevents human access to laser radiation.
3. If a protective housing is equipped with an access panel which provides "walk-in" access then:
a)means shall be provided so that any person inside the protective housing can prevent activation of a laser hazard that is equivalent to Class 3B
or Class 4.
b）There is a warning device is situated so as to provide adequate warning of emission of laser radiation equivalent to Class 3R in the
wavelength range below 400 nm and above 700 nm, or of laser radiation equivalent to Class 3B or Class 4 to any person who might be within
the protective housing.
c) Where “walk-in” access during operation is intended or reasonably foreseeable, emission of laser radiation that is equivalent to Class 3B or
Class 4 while someone is present inside the protective housing of a Class 1, Class 2, or Class 3R product shall be prevented by engineering
means.
NOTE Methods to prevent human access to radiation when persons are inside the protective housing can include pressure sensitive floor mats,
infrared detectors, etc.
Part 1： Security Statment Before Installation
4. The laser itself has a protective cover, the protective cover is fastened by screws. When the laser is installed on the laser engraver, the
protective cover should be checked to be reliably locked, and can not be removed in the energized state.
5. The housing of the laser engraver have an interlock function. When the housing is opened or removed, the laser can be automatically turned
off.
6. The laser engraver have an emergency stop button, which can immediately stop the output of the laser when pressed under unexpected
circumstances.
7. The laser engraver have a reset button, which can resume work under the condition of confirming safety after lifting the interlock or
emergency stop.
8. Laser engraver use physical keys, dongle, password system and other ways to manage and control, to prevent personnel without security
training operation of this kind of equipment.
9. On the laser engraver any window or channel that can actively observe or passively receive the laser radiation set up warning marks.
10. If the laser burns the skin or eyes, please go to a nearby hospital for examination and treatment immediately.
Laser Light can hurt the human eyes and skin. Do not expose the eye or skin to laser light directly. This Laser product has an optical lens and
emits a collimated laser beam. The light from this product, either direct or reflected is very harmful as it can propagate a long distance while
maintaining high optical density. When handling the product, must wear appropriate safety glasses (OD5+) to protect eyes from laser light
including reflected and stray light. The reflected and stray light spilling into an unintended area should be attenuated and/or absorbed.
2.1 Laser safety
We installed a laser shield on the laser, the shield can largely filter out the diffuse reflection of the laser spot. However, when using laser
engraving machine, it is recommended that you wear laser protective glasses. Avoid skin exposure to type 4 laser beams, especially at the
closed distance.Teenagers must have parental supervision in the process of using it. Do not touch the laser engraving module when the
machine is activated.
2.2 Fire safety
Because cutting burns off the substrate, a high-intensity laser beam generates extremely high temperatures and a lot of heat.Certain
materials can catch fire during cutting, creating gases and fumes inside the equipment.A small flame usually appears here when a laser beam
hits the material.It will move with the laser and will not stay lit when the laser passes by. Please do not leave the machine unattended during
the carving process. After use, be sure to clean up debris, debris and flammable materials in the laser cutting machine. Keep a working fire
extinguisher nearby at all times.Smoke or air pollutant safety. When laser engraving machines are used, smoke, vapour, particles, and
potentially highly toxic materials (plastics and other combustible materials) are produced from the material.These fumes or air pollutants can
be hazardous to health.
Part 2：User Security Statement
2.3 Material safety
Do not engrave materials with unknown properties. Materials Recommended:Wood, bamboo, leather, plastic, fabric, paper, opaque acrylic,
glass.Materials not recommended:Metal, precious stones, transparent materials, reflective materials etc.
2.4 Use Safety
Use the engraver only in horizontal position and ensure that it has been securely fixed to prevent fires caused by accidental shifting or
dropping from the workbench during work.It is forbidden to point the laser to people, animals or any combustible object, whether it is in
working condition or not.
2.5 Power safety
To prevent accidental disasters such as fire and electric shock, the Laser Engraver provides a power adapter with a
ground wire. Plug the power plug into the power socket with a ground wire when using the Laser Engraver.
2.6 Environment safety
Please ensure the workplace must be cleared while assembling engraving and cutting no flammable or explosive materials surrouding the
equitment. Have to set a metal plank under the bottom while engraving or cutting.
Part 3: Disclaimer and warning
This product is not a toy and is not suitable for people under 15 years of age. Do not allow children to touch the laser
Module. Please be careful when operating in scenes with children.
This product is a laser
module, visit http://www.atomstack3d.com/laserengraverdownload for complete "user manual" and the latest instructions and warnings. Shen
zhen AtomStack Technologies Co., Ltd. (Atomstack) reserves the right to update this Disclaimer and Safe Operation Guidelines.
Please be sure to read this document carefully before using the product to understand your legal rights, responsibilities and safety instructions;
Otherwise, it may bring property loss, safety accident and hidden danger of personal safety. Once you use this product, you shall be deemed to
have understood, accepted and accepted all terms and contents of this document. User undertakes to be responsible for his or her actions and
all consequences arising therefrom. User agrees to use the Product only for legitimate purposes and agrees to the entire terms and contents of
this document and any relevant policies or guidelines that AtomStack may establish.
You understand and agree that AtomStack may not be able to provide you with the cause of the damage or accident and provide you with
AtomStack's after-sale service unless you provide the original engraving or cutting files, engraving software configuration parameters used,
operating system information, video of the engraving or cutting process, and
operational steps prior to the occurrence of a problem or failure.
AtomStack is not liable for any and all losses arising from the user's failure to use the product in accordance with this manual,Without the
guidance of the company's technical personnel, users are prohibited from disassembling the machine by themselves. If this behavior occurs, the
loss caused by the user shall be borne by the user.
Atomstack has the ultimate right to interpret the document, subject to legal compliance. Atomstack reserves the right to update, modify, or ter
minate the Terms without prior notice.
Engraving machine introduction
Y轴 X-Axis
Support frame
Plum handle
Motor of X-Axis
Support frame
Scroll wheel of
X-Axis
Control box
Synchronous belt
Laser Module
Scroll wheel of Y-Axis
Eccentric nut
Motor of Y-Axis
Y-Axis
Part 4: Assembling instruction
Step1. Assembling instruction of X-Axis and Y-Axis
Step2. Assembling instruction of Y-Axis Bracket
Step3. Assembling instruction of Synchronous belt
Step4. Assembling instruction of Laser Module
Step5. Assembling instruction of connectivity cable
X-axis componentY-axis component
Components required
Step 1
1. As shown in Figure 1, push the X-axis assembly
along the dotted line into the guide rail frame on
the Y-axis assembly. Before pushing the X-axis
assembly into the Y-axis frame, use an open-end
wrench to loosen the eccentric nut to avoid
pushing into the Y-axis machine. The rollers on
the X-axis assembly are too tight when mounting.
2.As shown in Figure 2, after pushing the X-axis
assembly into the Y-axis guide rail, properly
tighten the eccentric nut on the X-axis assembly
with an open-end wrench to prevent the rollers
on the X-axis assembly from loosening.
3. As shown in Figure 3, it is a complete display of
the X/Y axis assembly after assembly.
2
eccentric nut
1
3
Tabla de contenidos
Idiomas:
Otros manuales de Grabador de ATOMSTACK
ATOMSTACK
ATOMSTACK A5 10W Manual de usuario
ATOMSTACK
ATOMSTACK A6 PRO Manual de usuario
ATOMSTACK
ATOMSTACK A5 Manual de usuario
ATOMSTACK
ATOMSTACK X7 Pro Series Manual de usuario
ATOMSTACK
ATOMSTACK A 5 Pro Manual de usuario
ATOMSTACK
ATOMSTACK M100 Manual de usuario
ATOMSTACK
ATOMSTACK X20 Pro Manual de usuario
ATOMSTACK
ATOMSTACK MAKER AC1 Manual de usuario
ATOMSTACK
ATOMSTACK Befon A5 Pro Plus Manual de usuario
ATOMSTACK
ATOMSTACK A5 M50 Pro Manual de usuario
