AT&T Merlin 1030 Manual técnico

AT&T

MERLIN

COMMUNICATIONS SYSTEM

PLANNING GUIDE:

MODELS 1030 AND 3070

WITH FEATURE MODULE 5

Table of Contents

Page

Introduction

Decisions

Square vs. Pooled Decision

About Square Systems

Standard Square Configurations

Customized Square Configurations

About Pooled Systems

Button Access vs. Dial Access to Line Pools

Automatic Route Selection

The Call Management System

Getting Started

Administrator/Attendant Console

Types of Consoles

Using the Console

Specifying Touch-Tone and Rotary Signaling

Call Restrictions

Allowed Lists

Automatic Route Selection (ARS)

ARS Default Tables

Group Page

Group Call Distribution

Enhanced Night Service

Night Service with Group Assignment

Night Service with Extra Alert

Night Service with Outward Restriction

Night Service with Time Set

Station Message Detail Recording (SMDR)

System Speed Dial Codes

Return interval for Transferred Calls

One-Touch Hold with Call Announcement

Voice Terminal Programmability

Auto lntercom

Automatic Line Selection

Call Coverage

Call Pickup

Do Not Disturb

Last Number Radial

Line Pickup

Notify (Send, Receive)

Outside Auto Dial

Personal Speed Dial

Personalized Ring

Privacy

Saved Number Redial

Simultaneous Voice and Data Calls

Touch-Tone Enable

Voice Announcement Disable

Initial Feature Assignments

Nonattendant Voice Terminals with 1030 or 3070 Configuration in Standard

Square Systems

Nonattendant Voice Terminals with 1520 Configuration in Standard Square

Systems

Nonattendant Voice Terminals in Pooled Systems

Administrator/AttendantConsole for Small Systems in Attendant Mode

Administrator/Attendant Console for Large Systems in Attendant Mode

Documents

Introduction

The advanced technology of the MERLIN communications system allows you to

customize the system to meet your business needs. As the system administrator, you

are responsible for selecting MERLIN system options and features that will enhance

your business operations.

This guide will help you decide which features to assign to your MERLIN system,

and to each voice terminal. Voice terminals are MERLIN system telephones. We

would like you to read through this guide and also the System Configuration Forms

before the Technical Customer-Support Specialist (TC-SS) assigned to your account

contacts you. Reading this guide beforehand will enable you to have an understand-

ing of the questions the TC-SS will ask you, and also how you want your system to

operate. Since the needs of customers vary, we need you to supply the information

contained in the System Configuration Forms to customize your system.

This planning guide explains everything you need to know to customize your

MERLIN communications system.

Here is what you need to do:

Read this planning guide, which is divided into the following sections:

●Decisions: This section helps you make the following systemwide

choices:

— How will people access outside lines? Will you have a square or pooled

system?

— If you decide to have a pooled system, how will people access the line

pools? Will they press a button or dial a number to get an outside line?

— Will you be using the Automatic Route Selection feature with your

MERLIN communications system?

— Will you have a Call Management System working with your MERLIN

communications system?

Getting Started: This section discusses systemwide features that will be

set by you when your system is installed. If necessary, you can change

these features at any time.

Voice Terminal Programmability: This section discusses the features that

are programmed at each voice terminal. Voice terminals can also be pro-

grammed from the administration console.

Initial Feature Assignments: This section shows you the initial features

preassigned to voice terminal buttons.

Documents: This section discusses the documentation that you will

●

receive with your MERLIN system and who the appropriate person for each

document would be.

After reading through this guide, remove the forms from the front pocket of

this package. Read through the “Instructions for Completing System and

Voice Terminal Configuration Forms.” If you want to begin filling out the forms,

follow the directions in those instructions to complete:

The System Configuration Form.

One Voice Terminal Configuration Form for each voice terminal in your

system (make enough photocopies of this form for all the voice terminals

in your system). When filling out this form, make certain that you have the

correct form for your system; there are several of these forms.

If you have any questions, please call the Technical Customer-Support

Specialist responsible for your account. You will find his or her name on the

letter that accompanies this package.

●

Decisions

SQUARE VS. POOLED DECISION

One of the first decisions you must make about your system is how people will access

outside lines from their voice terminals. The MERLIN communications system gives

you two configuration options for arranging your outside lines: square or pooled. In

a square system, each outside line appears on a separate button at each voice ter-

minal, except for those voice terminals with too few buttons to accommodate all the

lines. In a pooled system, outside lines are grouped together so that one button pro-

vides access to several outside lines. On administrator/attendant consoles, however,

each outside line appears on a separate button, whether your system is pooled or

square, and you cannot change this arrangement.

Whether your system should be square or pooled depends on your specific business

needs. If you want to use the Automatic Route Selection (ARS) feature, your lines

must be pooled and your system must be set for Dial Access to Line Pools (Dial

Access is discussed on page 8. The characteristics of both configurations are dis-

cussed in detail in the paragraphs that follow.)

ABOUT SQUARE SYSTEMS

A square configuration is one in which outside lines are represented by separate but-

tons on every voice terminal in the system. A square configuration simplifies call

handling because people can join in on calls or pickup calls on hold just by touching

the appropriate line button at almost any voice terminal.

You can choose between two kinds of square configurations: standard or cus-

tomized. In the standard configuration, you give all voice terminals in the system

access to the same lines. In the customized configuration, you assign specific lines

or sets of lines to selected groups of voice terminals. You can also assign personal

lines to individual voice terminals in a customized square configuration.

Standard Square Configurations

The standard square configuration is ideal for offices in which all employees use the

same lines to make and receive calls. In this arrangement, every line in the system

appears at each voice terminal that has enough buttons to accommodate that number

of lines. Depending upon the size of your system, you can assign up to 30 lines to

as many of your voice terminals as you want.

You assign each of your lines to the same buttons at each voice terminal. To get the

most from a standard square configuration, all your voice terminals should have

enough buttons to handle all the lines in your system. If you have ordered many

5-button voice terminals, keep in mind that they will be more difficult to use in a square

arrangement. An example of a standard square configuration appears below. All six

lines in the system are available for general use and appear on the same buttons

at each voice terminal, as shown.

Customized Square Configurations

In a customized square configuration, you assign individual lines or groups of lines

to selected voice terminals with similar requirements for placing and receiving calls.

This arrangement lets you tailor your communications system to meet the needs of

different departments. Calls are easily passed between departments using the Line

Pickup feature. This configuration also simplifies keeping records of calling patterns

within your business.

EXAMPLE OF STANDARD SQUARE CONFIGURATION

For example, the departments at a car dealership may have different calling needs.

Say that Ultimate Motors has eight local lines, three WATS lines, and one Foreign

Exchange (FX) line. The sales and office staff use the out-of-state WATS line frequently

to speak with manufacturers’ representatives, haulers, and other dealerships. This

group uses an in-state WATS line to contact customers, vendors, and the Division

of Motor Vehicle Registration in the state capital. The third WATS line is an incoming

in-state WATS line used by customers who live outside the immediate area. The ser-

vice staff doesn’t usually have to make long distance calls; however, one major equip-

ment supplier is located 25 miles away, and calls to this supplier would normally be

toll calls. To reduce this expense, Ultimate has a Foreign Exchange line for the sup-

plier’s exchange code, 560, When the staff uses this line, calls to the supplier are

treated as the equivalent of local calls. The manager handles many confidential

negotiations over the telephone and so requires a personal line.

A customized square configuration is the most appropriate system arrangement for

Ultimate Motors’ varied communications requirements. The administrator assigns

the three WATS lines and three of the eight local lines to the sales and office staff.

The service department’s voice terminals get three other local lines and the Foreign

Exchange line. The seventh local line is assigned to the voice terminal at the parts

desk, and the eighth is assigned as a personal line at the manager’s voice terminal.

The figure below illustrates this type of configuration.

Telephone Lines of Automobile Dealership

EXAMPLE OF CUSTOMIZED SQUARE CONFIGURATION

ABOUT POOLED SYSTEMS

For many businesses large enough to need the MERLIN system, Model 1030 or

Model 3070, pooled operation is more cost-efficient than a square one because:

●

The lines in the pool are shared by many people, so each line gets more use.

As a result, you may need fewer outside lines.

Only two buttons on each voice terminal are necessary to represent up to 30

interchangeable lines, so you can use more of the smaller, less expensive voice

terminal models.

Voice terminal buttons that would otherwise represent lines are used for system

features — a substantial advantage in systems with a large number of outside

lines or many 5- and 10-button voice terminals.

Automatic Route Selection allows you to determine which of your line pools pro-

vide the lowest cost, most efficient dialing methods for particular types of calls.

●

SIMPLE POOLED SYSTEM

The diagram above shows all lines assigned to a pool. You do not need to assign

all your lines to pools; you can assign individual lines that are not included in any

pool to any voice terminal in your system. For example, you can assign individual

special-purpose lines such as personal or WATS lines. Assigning a special line to

a button on one voice terminal in no way affects the use of the corresponding button

on other voice terminals. A diagram of a pooled system with eight lines appears below.

Line C

Line H

Line B Line G

Line A Line F

Intercom

Voice Line E

Attendant console

Intercom

Ring Line D

Main pool = Lines A, B, C

Line pool 2 = Lines E, F

Line pool 3 = G, H

Line not assigned to pool = Line D

Line pool 3 Line D Line pool 2

Main pool Main pool Main pool

Intercom-

Voice

Intercom-

Voice

Intercom-

Voice

Voice terminal 1 Voice terminal 2 Voice terminal 3

POOLED SYSTEM WITH 8 LINES

Button Access vs. Dial Access to Line Pools

NOTE: If you want to use Automatic Route Selection, you must select Dial Access

to Line Pools.

If you have decided to configure your system as pooled, you must also decide how

voice terminals will access the pools. You can choose one of two options for line

pools: Button Access to Line Pools or Dial Access to Line Pools.

If you have only one or two line pools, Button Access is the best option for your system.

If your system has several line pools, however, Dial Access is preferable because

you can access all pools by using only two buttons on each voice terminal. Dial

Access is also preferable if you want basic telephones to have access to more than

one line pool or if you want 5-button voice terminals to have access to more than one

special pool.

DIAL ACCESS TO POOLS

Assume that you have five line pools. With the Dial Access option (see the diagram

above), you arrange the system so that people can access any line pool by lifting

the handset, touching one of the two buttons above Intercom-Voice, and dialing the

access code assigned to the pool (9 for the main pool or 890 through 899 for the

others). Even if you set your system for Dial Access, you can still assign some pools

to particular buttons, if you like.

With the Button Access option (see the diagram below), people access all line pools

directly through pool buttons on each voice terminal. In such an arrangement, the

first two buttons above Intercom-Voice provide access to the main pool. You may

assign additional buttons for access to other pools that may include WATS lines, FX

lines, or lines used for special purposes.

BUTTON ACCESS TO POOLS

AUTOMATIC ROUTE SELECTION

If you decide to use the Automatic Route Selection (ARS) feature, you must configure

your system as Pooled with Dial Access to the pools. However, because you are using

ARS, the dialing of codes to access pools is eliminated when placing calls. When

placing a call, the user has to touch a Pool Access button, lift the handset, and then

dial the outside telephone number.

Your ARS routing patterns are determined by your system administrator. It is the

system administrator’s responsibility to decide which lines provide the lowest cost

and most efficient way to place calls for your business.

THE CALL MANAGEMENT SYSTEM (CMS)

The Call Management System (CMS) for the MERLIN communications system is

an automatic call distributor that answers calls and connects them to available agents.

Agents, of course, are your employees who answer incoming calls. In addition to

distributing calls, CMS provides current and historical data to a business in the form

of reports relative to call handling, line usage, and agent productivity. Using such

information, a business can make management decisions concerning how many

agents and lines it needs to support a specific function such as inside sales or

customer services, inquiries, or complaints. In addition, CMS offers a business a great

amount of flexibility to change the number of agents or line configurations to handIe

the needs of callers in the best way possible. If your business has CMS for the

MERLIN communications system, you need to administer your system to be com-

patible with this automatic call distributor.

Otros manuales para Merlin 1030

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Sistema de conferencias de AT&T

AT&T

AT&T MERLIN 820 Guía de instalación y uso

AT&T

AT&T SPIRIT 616 Manual de usuario

AT&T

AT&T PARTNER II Release 3.1 Guía rápida

AT&T

AT&T MERLIN LEGEND Release 2.0 Analog Multiline... Manual de usuario

AT&T

AT&T Merlin Legend 10BS Manual de usuario

AT&T

AT&T Partner Plus Manual de usuario

AT&T

AT&T MERLIN LEGEND Release 2.0 Single-Line... Manual de usuario

AT&T

AT&T MERLIN Plus Guía del usuario

AT&T

AT&T MERLIN LEGEND Release 2.0 Analog Multiline... Instrucciones de funcionamiento

AT&T

AT&T Merlin II Guía del usuario

AT&T

AT&T MERLIN LEGEND Release 2.0 Analog Multiline... Documento técnico

AT&T

AT&T Partner Series Guía de inicio rápido

AT&T

AT&T System 85 Manual de instalación y operación

AT&T

AT&T Spirit Communications System Manual de usuario

AT&T

AT&T MERLIN 410 Manual de lista de piezas

AT&T

AT&T MERLIN Plus Release 1 Manual de usuario

AT&T

AT&T Merlin 1030 Manual de usuario

AT&T

AT&T Merlin 1030 Manual de usuario

AT&T

AT&T MERLIN Plus Guía del usuario

AT&T

AT&T MERLIN LEGEND Release 2.0 Analog Multiline... Manual del propietario

AT&T

AT&T MERLIN 206 Manual de usuario

AT&T

AT&T Spirit Communications System Guía de instalación

AT&T

AT&T Merlin Legend BIS10 Manual de usuario

AT&T

AT&T MERLIN LEGEND Release 2.0 MLX Queued Call... Manual de usuario

Manuales populares de Sistema de conferencias de otras marcas

Kramer

Kramer VIA GO Manual de usuario

AVT

AVT MAGIC AC1 Go Manual de usuario

ProSoft Technology

ProSoft Technology AN-X4-AB-DHRIO Manual de usuario

Sony

Sony PCS-I150 Manual de usuario

Middle Atlantic Products

Middle Atlantic Products VTC Series Manual de usuario

Prentke Romich Company

Prentke Romich Company Vanguard Plus Guía

Speakerbus

Speakerbus iD 712 Manual de usuario

Trelleborg

Trelleborg SafePilot CAT PRO Manual de usuario

Sennheiser

Sennheiser ADN Manual de usuario

ADTRAN

ADTRAN NetVanta 7100 Manual de usuario

AINA

AINA PTT Voice Responder Manual de usuario

Yamaha

Yamaha ProjectPhone PJP-100H Manual de usuario

vissonic

vissonic VLI Series Manual de usuario

Panasonic

Panasonic KX-VC500 Manual de usuario

Poly

Poly Trio 8300 Manual de usuario

Crestron

Crestron Mercury CCS-UCA-SMK Dibujo dimensional

Inmarsat

Inmarsat mini M Manual de usuario

Tenveo

Tenveo ALL-IN-ONE Manual de usuario