Aries 2072101 Manual de usuario

PAGE 1 • 2072101-INS-RB• 877.287.8634 • NEED ASSISTANCE? • ARIESAUTOMOTIVE.COM

Product Image

Notes and Maintenance

Before you begin installation, read all instructions thoroughly.

Proper tools will improve the quality of installation and reduce the time required.

To protect the product, wax after installing. Regular waxing is recommended

to add a protective layer over the ﬁnish. Do not use any type of polish or wax

that may contain abrasives that could damage the ﬁnish.

For polished, gloss and other smooth ﬁnishes,

polish may be used to clear small scratches and scuffs on the ﬁnish.

Mild automotive detergent may be used to clean the product.

Do not use dish detergent, abrasive cleaners, abrasive pads,

wire brushes or other similar products that may damage the ﬁnish.

Refer to the table to the left when securing hardware during the

installation process to help prevent damage to the product or vehicle.

Level of Difﬁculty

Moderate

Parts List

1Winch support bracket

2Nut plate

2Hex bolt, M10 x 30mm

2Flat washer, M10

2Lock washer, M10

2Hex bolt, M12 x 30mm

2Flat washer, M12

2Lock washer, M12

Tools Required

Ratchet Torque wrench

Phillips

screwdriver

Flathead

screwdriver

10mm socket Deburring tool

16mm socket Touch-up paint

18mm socket Masking tape

Cut-off tool

Scan

for helpful

install tips

INSTALLATION MANUAL 2072101

Torque Speciﬁcations

METRIC

M6 bolt 3 ft.-lbs.

M8 bolt 7 ft.-lbs.

M10 bolt 25 ft.-lbs.

M12 bolt 45 ft.-lbs.

SAE

1/4" bolt 3 ft.-lbs.

5/16" bolt 7 ft.-lbs.

3/8" bolt 16 ft.-lbs.

7/16" bolt 20 ft.-lbs.

1/2" bolt 28 ft.-lbs.

Use above torque setting

unless otherwise noted

ARIESAUTOMOTIVE.COM • NEED ASSISTANCE? • 877.287.8634 • 2072101-INS-RB• PAGE 2

Step 1

Using a ﬂat head screwdriver, pry

and remove the four plastic push pins

securing the air dam in place. Remove

the air dam from underneath the vehicle.

Once removed, pry off the fasteners

securing the brackets to the frame.

Step 2

From behind the bumper, disconnect

the wiring harness attached to each fog

light. Unclip the wiring harness from the

bumper cover

Step 3

Locate the two fasteners securing

the frame cover in place on top of

the bumper. Remove these with a

Phillips screwdriver.

PAGE 3 • 2072101-INS-RB• 877.287.8634 • NEED ASSISTANCE? • ARIESAUTOMOTIVE.COM

Step 4

When facing the Jeep head-on,

slide the cover to the left to expose

the driver side bolts securing the bumper

in place. Remove the four nuts securing

the bolts onto the bumper frame with an

18mm socket.

Repeat this step on the passenger side.

Step 5

When all the bolts have been removed,

carefully lift the bumper from the frame

and set on a ﬂat work surface.

Step 6

Remove the front bolt securing

the vacuum pump to the frame.

Loosen the rear bolt securing the

vacuum pump to the frame and

rotate it to the left.

ARIESAUTOMOTIVE.COM • NEED ASSISTANCE? • 877.287.8634 • 2072101-INS-RB• PAGE 4

Step 9

Tuck the fog light wiring harness

into the frame channel.

Insert a nut plate, aligning the two

threaded holes with the holes in

the Jeep frame. Temporarily hold

in place with tape.

Repeat this process on the driver side.

Step 8

Pull out the wiring harness from

the side of the frame and place

tape on the nut plates.

Step 7

Cut off the vacuum bracket as shown

and deburr the cut edge. Use touch up

paint to protect raw metal.

PAGE 5 • 2072101-INS-RB• 877.287.8634 • NEED ASSISTANCE? • ARIESAUTOMOTIVE.COM

Step 10

Set the winch support bracket in place

making sure the wiring harness is routed

below the bracket as shown.

Step 11

Insert the M12 and M10 bolts with

ﬂat washers and lock washers.

Repeat this step on the driver side.

Do not tighten fasteners

until all four bolts are started.

Step 12

Remove the tape from both nut plates.

Using a torque wrench, torque

the M10 bolts to 25 ft./lbs. and

the M12 bolts to 45 ft./lbs.

ARIESAUTOMOTIVE.COM • NEED ASSISTANCE? • 877.287.8634 • 2072101-INS-RB• PAGE 6

Step 13

Congratulations on the installation

of your new winch support bracket.

With the winch support bracket installed,

periodic inspections should be

performed to ensure all mounting

hardware remains tight.

Note: Please refer to the instructions

provided with the front bumper, and

the winch manufacturers instructions

to complete the installation.

Tabla de contenidos

Otros manuales de Accesorios para automóviles de Aries

Aries

Aries P3067 Manual de usuario

Aries

Aries AL235040 Manual de usuario

Aries

Aries 1110315 Manual de usuario

Aries

Aries 3044 Manual de usuario

Aries

Aries 25201 Manual de usuario

Aries

Aries 205044 Manual de usuario

Aries

Aries 205040 Manual de usuario

Aries

Aries 35-2000 Manual de usuario

Aries

Aries 1501250 Manual de usuario

Aries

Aries 2153002 Manual de usuario

Aries

Aries Avicenum LYMPHO 360 Manual de usuario

Aries

Aries P2066 Manual de usuario

Aries

Aries S224047 Manual de usuario

Aries

Aries 204017 Manual de usuario

Aries

Aries S224046 Manual de usuario

Aries

Aries B35-2000 Manual de usuario

Aries

Aries 3069 Manual de usuario

Aries

Aries 2081004 Manual de usuario

Aries

Aries S223015 Manual de usuario

Aries

Aries 4524 Manual de usuario

Aries

Aries AL235041 Manual de usuario

Aries

Aries S223043-2 Manual de usuario

Aries

Aries AL234046 Manual de usuario

Aries

Aries 203039 Manual de usuario

Manuales populares de Accesorios para automóviles de otras marcas

James Baroud

James Baroud Odyssey Manual de usuario

Motorola

Motorola i50sx Manual de usuario

Yakima

Yakima 9MM STANDARD BIKE MOUNT Manual de usuario

Feniex

Feniex T3 Manual de usuario

Renault

Renault 77 11 423 180 Manual de usuario

Kia

Kia E8300-4D000 Manual de usuario

Brink

Brink 756843 Manual de usuario

Whispbar

Whispbar K085W Manual de usuario

v.link

v.link CI-VL2-PC-HSD Manual de usuario

Viking

Viking Stack-Rack Guía de configuración rápida

Choetech

Choetech AT0005 Manual de usuario

ZZ2

ZZ2 ZZAIR-PRO Manual de usuario

Holman

Holman 4A80L Manual de usuario

Thule

Thule 2075 Manual de usuario

Motorola

Motorola T325 Manual de usuario

TAUBENREUTHER

TAUBENREUTHER 16-3950 Guía de instalación

DV8

DV8 FBJL-02 Manual de usuario

Prorack

Prorack K1163 Manual de usuario