ARGON18 NITROGEN DISC 286A Manual de usuario

NITROGEN DISC 286A: ASSEMBLY GUIDE

Valid for MY2019 Nitrogen Disc 286A

Revision 1.0 - 07-26-2018

1. Tools Needed and First Aid Kit ...........................3

2. Frameset inspection .....................................4

3. Frameset Parts, SKUs and descriptions ..................5-6

4. Assembly instructions ................................7-22

4.1. Headset Installation ...............................7-9

4.2. Seat Post Installation................................10

4.3. Seat Post Assembly .................................11

4.4. Front Derailleur Adjustement .......................12

4.5. Rear Derailleur Hanger Adjustment ..................13

 4.6.Mechanicalgroupsetspecication ............... 14-16

 4.7.Electronic(Di2)groupsetspecication ........... 17-21

 4.8.Electronic(Wireless)groupsetspecication ..........22

For the warranty to be valid, the bicycle must be fully assembled by an authorized Argon 18 dealer. High end components,

particularly carbon parts, need extra care when assembled. These components must be installed using a calibrated torque

wrench to make sure every bolt is at the right torque setting to prevent damage.

NITROGEN DISC 286A: Table of Contents

My Nitrogen Disc

Date of purchase:

Retailler:

Size:

Serial Number:

Tools needed for assembly

1: Bearing Cup Press (Park Tool HHP-2)

2: Allen Key Set

3: Grease

4: Utility Pick Set (Park Tool Item #UP-SET)

5: Clean Rags

6: Derailleur Hanger Alignment Gauge (Park Tool Item #DAG-2 or #DAG-2.2)

7: Cables and Housing Cutter

8: Carbon Paste

9: Loctite #242

10: Torque Wrench

First Aid Kit: Essential parts to always have on hand

IN CASE OF EMERGENCY…THIS MIGHT SAVE YOUR RIDE!

1: Spare rear derailleur hanger assembly

2: Seat post collar

NITROGEN DISC 286A: 1. Tools Needed and First Aid Kit

80802 80832

(Direct mount option if utilized)

Parts installed on the frame Description Screw Tork Detail

type Nm

Front derailleur hanger Screw (2) 5mm 4Nm Loctite

Rear derailleur hanger Screw 4mm 2Nm Loctite

Bottle cage Screw (4) 5mm 3Nm Grease

Bottom bracket cable guide Screw 5mm 1.5Nm Grease

IMPORTANT:

The following parts are assembled on the frame. When assembling the bike, you will need to adjust these parts according to their torque

specications.

NITROGEN DISC 286A: 2. Frame Inspection

BEFORE ASSEMBLING YOUR NEW NITROGEN DISC, MAKE SURE THAT YOU HAVE ALL THE FOLLOWING:

1: Frameset parts checklist (see p.5)

2: Inspect the frame for cosmetic aspect (scratches, bumps, cracks, paint defect, etc.)

3: For reference, check serial number and write it on p.2

4: All the necessary bolts (refer to Frameset Parts, p.5)

5: For optimal shifting performance, use a dropout alignment gauge to make sure that the drive-side dropout is

straight (p.13)

NITROGEN DISC 286A: 3. Frameset Parts, SKUs and descriptions

38757

38885 38260

38884

80802

38882

38724

38880 38888

FK.NIT_D.286A

SP.NIT_D.286A

38881 38879 39009

80375,

80478

80374,

80477

running change

Images are for reference only. Proportions are not accurate.

Argon 18 reserves the right to modify/change parts of the frameset at any moment without prior notice.

*For more info please consult notice on Seatpost clamp dated 2016-06-09

8099981000

80832

80812 80813

80551

NITROGEN DISC 286A 3. Frameset Parts, SKUs and descriptions

No. Name Assembled on A18 SKU# Qty

Parts already assembled

Parts

1 Nitrogen Disc Frame - - 1

2 Nitrogen Disc Fork - FK.NIT_D.286A 1

3 Nitrogen Disc Seat Post Assembly - SP.NIT_D.286A 1

4 Head Tube Brake Cable Stopper Frame 38878 1

5 Top Tube Cable Stopper Frame 38879 1

10 BB Cover (incl. screw) Frame 38260 1

11 Seat Clamp Base (incl. screw) Frame 80375, 80478 1

12 Seat Clamp Wedge (incl. screw) Frame 80374, 80477 1

13 Di2 Cable Grommet Frame 38888 1

14 Mechanical Cable Grommet (Top Tube) Frame 38880 1

15 Di2 Grommet (Top Tube) Frame 38881 1

16 3D Headset Assembly Fork 38724 1

19 Chainstay Cable Grommet Frame 39009 1 Set

20 Internal Di2 Battery Support Seat Post 38757 1 Set

21 8mm Wrench for Seat Clamp - 38543 1

22 HT Rear Brake Grommet Di2 Frame 81000 1

23 HT Rear Brake Grommet Frame 80999 1

24 Direct Mount Rear Derailleur Hanger Frame 80832 1

25 DT Swiss RWS Thru-axle FRONT 12 x 119mm Fork 80812 1

26 DT Swiss RWS Thru-axle REAR 12 x 161mm with handle Frame 80813 1

27 TT Di2 Plug Frame 80026 1

28 Oblong Cable Guide Frame 80551 2

29 Rear derailleur plug for eTap Frame 80825 1

30 Round plug Frame 80554 1

31 TT grommet (Di2) Frame 38881 1

8 Rear Derailleur Hanger (incl. dropout, screw) Frame 80802 1

6 Front Derailleur Hanger (incl. screws) Frame 38882 1

9 BB Cable Guide (incl. screw) Frame 38885 1

7 Bottle Cage Screws Frame 38884 4

*Except for the frame itself, which is not sold as a spare part, all parts can be ordered by referring to their respective SKU number.

Install the 3D headset (16.3 & 16.4)

accordingtotheAEROPresstassembly

guide.Youcanchoosefrom3dierent

heights: 25mm, 15mm or 0mm.

NITROGEN DISC 286A: 4.1. Headset Installation

16.3 & 16.4

GREASE

NITROGEN DISC 286A: 4.1. Headset Installation

25mm

15mm

0mm

setup

5 5

Compressor

Top cap (including O-ring & seal)

Micro spacers

Compression ring

Bearing

3D bearing holder

Plastic sleeve (no need for 0mm setup)

Top cap for 0mm setup

head tube

(bike)

head tube

(bike)

head tube

(bike)

To remove the 3D bearing holder, insert the Park Tool

RT-1 and then tap it carefully until the spacer comes out.

STEP

Inspect the bike’s head tube for any sharp edges and

apply a small amount of grease.

STEP

For the 25mm and 15mm setups, lightly grease the

bottom section of the 3D bearing holder (6) and insert

the plastic sleeve (7).

STEP

Position the headset inside the head tube. Place

the top 3D assembly with the headset bearing inside

(this will prevent the sleeve from getting damaged).

Add the compression ring on top of the bearing, then

add the press t 3D system tool and softly press down

the assembly until it bottoms out using a Bearing Cup

Press (Park Tool HHP-2). Then, insert the bottom

bearing (5), compression ring (4) micro spacers (3) and

top cap (2), slide the fork and stem and measure the

steerer length needed.

For the 0mm setup , do not use the plastic sleeve.

Install the 3D bearing holder (6) with grease applied

directly inside the frame.

STEP

First, you must assess which setup suits your needs:

25mm, 15mm or 0mm.

NITROGEN DISC 286A: 4.1. Headset Installation

Compressor

Top cap (including O-ring and seal)

Micro spacers

Compression ring

Bearing

3D bearing holder

Plastic sleeve (no need for 0mm setup)

Top cap for 0mm setup

Press Fit 3D system tool 1 1/4”

Bearing Cup Press (Park Tool HHP-2)

IMPORTANT: Use the Press Fit 3D system tool 1 1/2” with

the Bearing Cup Press (ParkTool HHP-2) to avoid any

damage on the bike frame.

NITROGEN DISC 286A: 4.2. Seat Post Installation

1. Place the seat post collar inside the

frame.

2. Insert the seatpost (3) on which

somecarbonberassemblygelhas

been applied.

3. Position the seatpost to the desired

height.

4. Apply a drop of blue Threadlocker

(n. 242) on the bolt’s thread

5. Tighten the set screw at max. 5.5Nm

while leaving a space between the two

parts allowing them to slide.

GREASE

THREADLOCKER

BLUE (n. 242)

LOCTITE

GREASE

CARBON FIBER

ASSEMBLY

COMPOSITE

5.5 Nm

1Nm

RUNNING CHANGE

Tabla de contenidos

Otros manuales de Bicicleta de ARGON18

ARGON18

ARGON18 E-118 NEXT Manual de usuario

ARGON18

ARGON18 GALLIUM CS DISC 362A Manual de usuario

ARGON18

ARGON18 GALLIUM PRO Manual de usuario

ARGON18

ARGON18 E-118 NEXT Manual de usuario

ARGON18

ARGON18 GALLIUM DISC 339A 2021 Manual de usuario

ARGON18

ARGON18 SUM PRO 2022 Manual de usuario

ARGON18

ARGON18 GALLIUM 348A Manual de usuario

ARGON18

ARGON18 GALLIUM 279A Manual de usuario

ARGON18

ARGON18 KRYPTON PRO Manual de usuario

ARGON18

ARGON18 GALLIUM DISC 280A Manual de usuario

ARGON18

ARGON18 GALLIUM PRO Manual de usuario

ARGON18

ARGON18 NITROGEN 231A Manual de usuario

ARGON18

ARGON18 KRYPTON 212A Manual de usuario

ARGON18

ARGON18 nitrogen Manual de usuario

ARGON18

ARGON18 MY2016 Nitrogen Pro Manual de usuario

ARGON18

ARGON18 ELECTRON PRO Manual de usuario

ARGON18

ARGON18 GALLIUM PRO DISC 338A 2021 Manual de usuario

ARGON18

ARGON18 E-80 Manual de usuario

ARGON18

ARGON18 KRYPTON GF 273A Manual de usuario

ARGON18

ARGON18 E-118 NEXT Manual de usuario

ARGON18

ARGON18 Road Racing Manual de usuario

ARGON18

ARGON18 E-Road Manual de usuario

ARGON18

ARGON18 RADON 237A Manual de usuario

ARGON18

ARGON18 NITROGEN PRO 230A Manual de usuario

Manuales populares de Bicicleta de otras marcas

RAMBO

RAMBO R1000X2M-FF-BFD Manual de usuario

Vermeiren

Vermeiren SAFARI Manual de usuario

Velec

Velec A2/36V Manual de usuario

Coswheel

Coswheel A-ONE Manual de usuario

Betzold

Betzold 97869 Manual de usuario

Cervélo

Cervélo S3 2019 Manual de usuario

Tenways

Tenways AGO X Manual de usuario

Festo

Festo EGSC-BS-KF Manual de lista de piezas

Gio Electric

Gio Electric H1 Volt Manual de usuario

GOGOBEST

GOGOBEST GM30 Manual de usuario

DAHON

DAHON CIAO - 2009 Manual de usuario

Aprimatic

Aprimatic ONDA 500 Guía de inicio rápido

MV Agusta

MV Agusta Lucky Explorer GRAVEL Manual de instrucciones

Greyp

Greyp G6 Series Manual de usuario

Babboe

Babboe Carve-E Manual de usuario

Huka

Huka orthros Manual de usuario

Xtracycle

Xtracycle Stoker 2021 Manual de usuario

APRILIA

APRILIA DORSODURO 750 ABS 2015 Manual de usuario