ARGON18 KRYPTON XROAD 213C Manual de usuario
KRYPTON XROAD 213C: ASSEMBLY GUIDE
Revision 5.0 - 05-23-2017
Assembly overview.........................................2
1. Frame inspection ........................................3
2. Headset installation......................................4
3. Cable housing installation & hydraulic routing ..........5-7
4. Electronic drive-train specication.....................8-12
5. Saddle adjustment .................................. 13-14
6. Derailleur hanger adjustment............................15
7. Parts’ SKUs and Descriptions ............................16
For the warranty to be valid, the bicycle must be fully assembled by an authorized Argon 18 dealer. High end components,
particularly carbon parts, need extra care when assembled. Those components must be installed using a calibrated torque
wrench to make sure every bolt is at the right torque setting to prevent damage.
No more than 30mm of spacer can be place between the stem and the top cap of the 3D system.
And the use of more than 5mm spacer on top of the stem could void the eciency of the compressor.
These practices will automatically cancel any warranty claim against the manufacturer.
KRYPTON XROAD 213C: Table of contents
2. Headset installation 3. Cable housing installation
IMPORTANT NOTICE: It is easier to install the
cables and cable housings before the crank set.
5. Seatpost adjustment 6. Derailleur hanger adjustment
2
KRYPTON XROAD 213C: Assembly overview
4. Electronic drive-train cable
routing specication
1. Frame inspection
3
KRYPTON XROAD 213C: 1. Frame inspection
Parts installed on the frame Description Screw Tork Detail
type Nm
1 Seatpost, Ø 27.2mm Seatpost Carbon paste
2 Front derailleur hanger Screw 3mm 3Nm Loctite
3 Rear derailleur hanger Screw (2) 3mm 4Nm Loctite
4 Bottle cage Screw (4) 4mm 3Nm Grease
5 Seatpost collar Clamp 4mm 6Nm Grease
6 Rear derailleur cable stopper Screw (2) 2mm 2Nm Loctite
7 Bottom bracket cable guide Screw 5mm 3Nm Grease
When assembling a new frame, be sure to check if the following parts are assembled correctly.
4
KRYPTON XROAD 213C: 2. Headset installation
6
Install the 3D headset (6) according to
the presst assembly guide. You can
choose from 3 dierent heights: 25mm,
15mm or 0mm.
5
KRYPTON XROAD 213C: 3. Cable housing installation
Suggested lengths of the cable housing
housing/size
Front brake
Rear brake
Front derailleur
Rear derailleur
79cm
144cm
140cm
198cm
79cm
144cm
142cm
200cm
79cm
144cm
144cm
202cm
89cm
164cm
146cm
204cm
XS
79cm
144cm
138cm
196cm
XXS S M L
89cm
164cm
148cm
206cm
XL
A: barrel adjuster
B: plastic cap
B
B
B
speed adjustment: B+A+B
B
Install the front and rear derailleur
cable starting at the top of the down
tube.
For the derailleur and hydraulic
housing, measure a sucient length
of housing to be able to turn the
handlebar both ways correctly.
6
KRYPTON XROAD 213C: 3. Cable housing installation
Hydraulic brakes housing
Font section: Measure the necessary housing to ensure proper rotation of the handlebar. Insert the housing
through the fork starting at the caliper.
Rear section: Remove both brake grommets (4j - front & rear). Run the hydraulic housing from the back of the
bike to the front, and connect the housing to the lever as recommended by the brake manufacturer.
4j
4j
7
KRYPTON XROAD 213C: 3. Cable housing installation
Front and rear derailleur: Pass
the two cables inside the frame
starting the top tube until they
come out under the bottom
bracket.
Pass both cables into the cable
guide (4d). Make sure the 5mm
screw is set to 1.5 Nm.
For a Di2 conguration, use
the bottom bracket dedicated
cover for electric shifting (4i).
It’s better to install the cables
before installing the bottom
bracket and crank.
4i
4d
8
KRYPTON XROAD 213C: 4. Electronic drive-train specication
The Di2 cable routing can be achieved easily using this
simple trick: use a brake cable and a metal cable end to
x the Di2 cable. For more information on Shimano Di2
electronic system installation, go to: http://si.shimano.com.
The same method can be use for hydraulic cable housing
routing.
9
Use the proper grommet on
the downtube to x the cable
correctly, depending if you use
mechanical (4h) or electronic
(5b-5c) drive-train.
5b
4h
5c
KRYPTON XROAD 213C: 4. Electronic drive-train specication
Tabla de contenidos
Otros manuales de Bicicleta de ARGON18
ARGON18
ARGON18 ELECTRON PRO 245A Manual de usuario
ARGON18
ARGON18 E-112 Manual de usuario
ARGON18
ARGON18 E-118 TRI+ Disc 315A Manual de usuario
ARGON18
ARGON18 GALLIUM CS DISC 322A Manual de usuario
ARGON18
ARGON18 GALLIUM 260A Manual de usuario
ARGON18
ARGON18 KRYPTON PRO 333A Manual de usuario
ARGON18
ARGON18 GALLIUM PRO Manual de usuario
ARGON18
ARGON18 E-117 TRI Disc 317A Manual de usuario
ARGON18
ARGON18 GALLIUM CS DISC 362A Manual de usuario
ARGON18
ARGON18 MY2016 Nitrogen Pro Manual de usuario
ARGON18
ARGON18 E-119 TRI Manual de usuario
ARGON18
ARGON18 GALLIUM 279A Manual de usuario
ARGON18
ARGON18 NITROGEN DISC 286A Manual de usuario
ARGON18
ARGON18 E-119 TRI+ Manual de usuario
ARGON18
ARGON18 SUBITO Manual de usuario
ARGON18
ARGON18 GALLIUM PRO DISC 338A Manual de usuario
ARGON18
ARGON18 GALLIUM 348A Manual de usuario
ARGON18
ARGON18 E-119 TRI+ Manual de usuario
ARGON18
ARGON18 Road Racing Manual de usuario
ARGON18
ARGON18 GALLIUM PRO 347A Manual de usuario
