ARGON18 E-117 TRI Disc 317A Manual de usuario
E-117 TRI Disc 317A / 317B : ASSEMBLY GUIDE
Valid for MY2020 E-117 Tri Disc 317A / 317B
Revision 2.0 - 02.10.2019
2
For the warranty to be valid, the bicycle must be fully assembled by an authorized Argon 18 dealer. High end components,
particularly carbon parts, need extra care when assembled. These components must be installed using a calibrated torque
wrench to make sure every bolt is at the right torque setting to prevent damage.
Table of Contents
My E-117 Tri Disc
Date of purchase:
Retailler:
Size:
Serial Number:
1. Tools Needed & First Aid Kit .......................................... 3
2. E-117 TRI Disc 317A Frameset Parts .................................. 4
3. E-117 TRI Disc 317A Parts’ SKUs and Descriptions*.................... 5
4. Seat Post Clamp Installation .......................................... 6
5. Seat Post Installation................................................. 7
6. Seat Post Installation................................................. 8
7. Frame Inspection .................................................... 9
8. Rear Derailleur Hanger Adjustment ..................................10
9. Front Derailleur Hanger Adjustment .................................11
10. Headset Installation ...............................................12
11. Cable Housing Installation for mechanical drive train................15
12. Cable Housing Installation for electrical drive train..................16
13. Cable Housing Installation .........................................17
14. Rear derailleur grommet ...........................................19
15. Electronic Drive-train Installation...................................20
16. Saddle Adjustment ................................................21
17. Troubleshooting / Tips .............................................22
18. Min/Max Seat Post Insertion .......................................23
3
Tools needed for assembly
1: Bearing Cup Press (Park Tool HHP-2)
2: Allen Key Set
3: Grease
4: Utility Pick Set (Park Tool Item # UP-SET)
5: Clean Rags
6: Derailleur Hanger Alignment Gauge (Park Tool Item # DAG-2,2)
7: Cables and Housing Cutter
8: Carbon Paste
9: Loctite #242 or #243
10: Torque Wrench
First Aid Kit: Essential parts to always have on hand
IN CASE OF EMERGENCY…THIS MIGHT SAVE YOUR RIDE!
1: Spare rear dropout (SKU: 80832 for Direct Mount and 80802 for regular)
2: Spare brake pads corresponding to your caliper and disc model
3: Seat clamp (SKU: 80423, 80422)
IMPORTANT: the E-117 Tri Disc’s seat clamp (1.5-1.6) is not the same as the Nitrogen
1. Tools Needed & First Aid Kit
SKU: 80422
SKU: 80423
SKU: 80802SKU: 80832
4
2. E-117 TRI Disc 317A Frameset Parts
Images are for reference only.
Argon 18 reserves the right to modify/change parts of the frameset at any moment without prior notice.
31.5
1.18
1.19
1.111.91.101.19
4
6
1
2
1.7
1.8.2
1.13
1.3.2
1.3.1
1.4
1.12
1.21
1.2
1.8.1
1.17
1.14
1.16
1.15
5
7
1.3.3
1.6
3.2
Complete headset
Not shown on the image:
- Di2 battery holder
- Foam liner for hydraulic hoses
5
3. E-117 TRI Disc 317A Parts’ SKUs and Descriptions*
*Except for the frame itself, which is not sold as a spare part, all parts can be ordered by referring to their respective SKU number.
No. Name A18 SKU# Qty
1 E-117 TRI DISC FRAME N/A 1
1,2 FRONT DERAILLEUR HANGER (W. SCREWS) 38882 1
1,3,1 REAR DERAILLEUR HANGER STANDARD
80802
1
1,3,2 REAR DROPOUT DS 1
1,3,3 REAR DERAILLEUR HANGER SCREW M4x12 FLAT HEAD 1
1,4 REAR DERAILLEUR HANGER DIRECT MOUNT 80832 1
1,5 SEAT POST COLLAR BASE W. SCREW M8X12 80423 1
1,6 SEAT POST COLLAR WEDGE W. SCREW M3X8 80422 1
1,7 BB CABLE GUIDE 80492 1
1,8,1 BB CABLE COVER 80159 1
1,8,2 BB CABLE COVER SCREW M4x6 2
1,9 TT GROMMET MECH 36656 1
1,10 TT GROMMET Di2 36670 1
1,11 TT GROMMET WIRELESS 81094 1
1,12 FD CABLE ENTRY GROMMET 80164 1
1,13 FD CABLE ENTRY PLUG 80826 1
1,14 ROUND GROMMET MECH 80985 1
1,15 ROUND PLUG 80804 1
1,16 ROUND GROMMET DI2 80805 1
1,17 OBLONG HOSE GUIDE 80551 1
1,18 SCREW FOR BOTTLE CAGE AND FRONT DERAILLEUR
M5x16 ROUND HEAD
81003 5
1,19 PLASTIC PLUG M5 80264 3
2 E-117 TRI DISC FORK FK.E117T_D.317A 1
3 E-117 TRI ASP-7050 SEAT POST (INCL. SHAFT + HEAD) SP.E117T.285A 1
3,2 RITCHEY SEAT POST HEAD N/A in spare part; Available at ritcheylogic.com 1
3,3 DI2 BATTERY HOLDER 80167 1 kit
4 HEAD SET NO.37-E 80096 1
5 A18 REAR THRU AXLE M12x161 81053 1
6 A18 FRONT THRU AXLE M12x119 81052 1
7 A18 THRU AXLE LEVER 81054 1
8 FOAM LINER FOR HYDRAULIC HOSE 80811 1
6
4. Seat Post Clamp Installation
1. Apply a drop of blue Threadlocker
(n. 242) on the bolt’s thread
2. Apply grease on the seat post clamp
and on the screws as shown
3. Assemble the seat post clamp with
the small screw, allowing the parts to
move freely
4. Place the seat post clamp inside the
frame, holding it to prevent it falling
inside the frame
5. Insert the seatpost (3), on which
some carbon ber assembly paste has
been applied
6. Position the seatpost to the desired
height
7. Tighten the set screw at max. 5.5Nm
IMPORTANT: The E-117 Tri Disc’s seat
clamp is not the same as the Nitrogen
GREASE
THREADLOCKER
BLUE (n. 242)
GREASE
CARBON FIBER
ASSEMBLY PASTE
5.5 Nm
Thighten lightly, then unscrew a
1/4 turn to keep the wedge free to
slide
1,5
1,6 THREADLOCKER
BLUE (n. 242)
7
5. Seat Post Installation
B
A
C
1. Unscrew main bolt (A) as far as
possible without fully removing it from
the lock nut.
2. Install the saddle rails into the
seatpost clamp (B).
3. Slide saddle clamp (B) onto rocker (C).
4. Tighten the bolt up at 12Nm.
See p.23 for saddle adjustment.
IMPORTANT:
The E-117 Tri Disc’s saddle rail clamp is
made for metal and round-shaped saddle
rails (For part numbers contact Ritchey).
For other types of saddle rails, please
refer to the Tips and Troubleshooting
section of this Assembly Guide (p.22).
12Nm
CARBON
FIBER
ASSEMBLY
PASTE
5Nm
5Nm
3
8
6. Seat Post Installation
The Di2 battery is hidden in the
seatpost; use the Di2 battery holder
(3.3) to x the battery correctly. Apply a
slight amount of grease on both parts.
GREASE
GREASE
3.3
CARBON
FIBER
ASSEMBLY
PASTE
9
7. Frame Inspection
Parts installed on the frame Description Screw Torque Detail
type Nm
Front derailleur hanger Screw (2) 5mm 4Nm Threadlocker
Rear derailleur hanger Screw (1) 4mm 2Nm Threadlocker
Bottle cage Screw (4) 5mm 3Nm Grease
Bottom bracket cover Screw (2) 4mm 2.5Nm Grease
IMPORTANT:
The following parts are assembled on the frame. When assembling the bike, you will need to adjust these parts according to their
torque specications.
BEFORE ASSEMBLING YOUR NEW E-117 TRI DISC, MAKE SURE THAT YOU HAVE ALL THE FOLLOWING:
1. Brakes hoses, gears cables and housing set
2: Frameset parts checklist (see p.5)
3: All the necessary bolts (refer to Frameset Parts, p.5)
WHEN ASSEMBLING YOUR NEW E-117 TRI DISC, MAKE SURE YOU FOLLOW THIS PROCEDURE:
4: Inspect the frame for cosmetic aspect (scratches, bumps, cracks, paint defect, etc.)
5: For reference, check serial number and write it on p.2
6: For optimal shifting performance, use a dropout alignment gauge to make sure that the drive-side dropout is straight.
10
8. Rear Derailleur Hanger Adjustment
1. Select the correct rear derailleur hanger depending on the type of derailleur
that you have.
- Direct mount (1.4)
- Regular mount (1.3.1)
2. Make sure to align the rear derailleur hanger using a Derailleur Hanger
Alignment Gauge like Park Tool Item #DAG-2,2.
For any assistance, visit Park Tool’s website:
www.parktool.com/product/derailleur-hanger-alignment-gauge-dag-2-2
1.4
1.3.1
1.3.2
1.3.3
1.3.2
1.3.3
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Bicicleta de ARGON18
ARGON18
ARGON18 KRYPTON PRO Manual de usuario
ARGON18
ARGON18 GALLIUM PRO Manual de usuario
ARGON18
ARGON18 KRYPTON Manual de usuario
ARGON18
ARGON18 SUM PRO 2022 Manual de usuario
ARGON18
ARGON18 GALLIUM CS 281A Manual de usuario
ARGON18
ARGON18 E-118 TRI+ Disc 315A Manual de usuario
ARGON18
ARGON18 KRYPTON XROAD 213C Manual de usuario
ARGON18
ARGON18 E-119 TRI+ Manual de usuario
ARGON18
ARGON18 GALLIUM PRO Manual de usuario
ARGON18
ARGON18 GALLIUM PRO DISC 338A 2021 Manual de usuario
ARGON18
ARGON18 E-119 TRI+ Manual de usuario
ARGON18
ARGON18 NITROGEN DISC 286A Manual de usuario
ARGON18
ARGON18 E-119 TRI Manual de usuario
ARGON18
ARGON18 GALLIUM CS DISC 362A Manual de usuario
ARGON18
ARGON18 E-119 TRI Manual de usuario
ARGON18
ARGON18 NITROGEN PRO 230A Manual de usuario
ARGON18
ARGON18 GALLIUM 260A Manual de usuario
ARGON18
ARGON18 ELECTRON PRO Manual de usuario
ARGON18
ARGON18 E-119 TRI+ Manual de usuario
ARGON18
ARGON18 GALLIUM 279A Manual de usuario
