Argo MARGE Manual de usuario

V 05/22

MARGE

DIGITAL CERAMIC FAN HEATER

This product is only suitable for correctly-insulated

environments or for occasional use.

OPERATING INSTRUCTIONS

Read the instructions carefully before operating the appliance or carrying out maintenance operations.

Observe all the safety instructions; failure to observe the instructions may lead to accidents and/or damage.

Keep these instructions in a safe place for future reference.

V 05/22

GENERAL SAFETY INFORMATION

• Use this fan heater only as outlined in this manual. Any other use not

recommended by the manufacturer may cause fire, electric shock or

injury to persons.

• Make sure that the type of mains power complies with the electrical

requirements of the fan heater (220-240V~/50-60 Hz).

• This appliance can be used by children of at least 8 years of age

and by people with reduced physical, sensory or mental abilities, or

who lack sufficient experience or the necessary knowledge, provided

that they are supervised or have been instructed on how to use the

appliance safely and understand the hazards related to its use.

• Children must not be allowed to play with the appliance.

• Cleaning and maintenance operations normally carried out by the user

must not be performed by unsupervised children.

• This product is not a toy. Children under the age of 3 must be kept

away if not continuously supervised.

• Children aged between 3 and 8 must only turn the appliance on/

off as long as it has been placed or installed in its normal operating

position and that they receive surveillance or instructions regarding the

safe use of the appliance and understand the dangers.

• Children between 3 and 8 years of age must not insert the plug, adjust

or clean the appliance or carry out maintenance by the user.

• WARNING: Certain parts of this product may become very hot

and cause burns. Special care should be taken when children and

vulnerable people are nearby.

• To avoid the risk of accidentally resetting the thermal protection, this

appliance must not be powered through an external switching device,

such as a timer, or connected to a circuit that is switched on and off by

the utility.

• WARNING: do not use the fan heater with a controller or any other

device that activates the appliance automatically, as there may be a

risk of re if the fan heater is covered or incorrectly positioned.

• Do not restrict the air inlet and outlet grilles.

• The appliance heats up significantly when running and can cause burns.

Avoid unprotected contact with the hot surface.

• Keep flammable materials, such as furniture, cushions, blankets, paper,

V 05/22

cloths, curtains and similar items at least 1 m away from the front, sides

and back of the appliance.

• Disconnect the mains power when the appliance is not in use or during

cleaning.

• Avoid using the fan heater in dusty environments or in the presence of

flammable vapours (e.g. in workshops or garages).

• Do not place anything on the product; avoid placing wet garments on

the fan heater.

• Use the heater in a well-ventilated area.

• Avoid placing fingers or foreign objects in the air inlet/outlet grilles, as

this may lead to electric shock or fire and may damage the appliance.

• To avoid the risk of fire, do not block the grilles or tamper with them in

any way while the fan heater is in use.

• Do not use the appliance if the power cable or plug are damaged.

If the power cable is damaged, it must be replaced by the manufacturer

or its technical assistance service or in any case by a person with a

similar qualification, in order to prevent any risk.

• Do not use the fan heater if it has fallen from a certain height or if it has

been damaged in any way. Contact a service centre to check the fan

heater or make any necessary electrical or mechanical repairs.

• The most common cause of overheating is the build-up of dust in

the appliance. Remove accumulated dust by removing the plug and

cleaning the grilles using a vacuum cleaner.

• Do not use any abrasive products to clean the appliance. Clean it

using a damp cloth (not wet) rinsed with soapy water. Remove the plug

from the socket before performing any maintenance.

• To disconnect the fan heater, turn the switch to OFF and remove the

plug from the socket. Pull on the plug only. Do not pull on the cable

when turning off the fan heater.

• Do not place any objects on the cable and also avoid bending the

• cable.

• Using extension leads is not recommended as they may overheat and

cause a fire hazard. Never use a single extension lead to operate

multiple appliances.

• Do not immerse the power cable, plug or any other part of the appliance

in water or other liquids.

V 05/22

• Do not touch the plug with wet hands.

• Do not place the fan heater above or near another heat source.

WARNING: AVOID COVERING THE FAN HEATER TO PREVENT

IT FROM OVERHEATING.

The symbol below signals this warning:

• The fan heater may cause the risk of fire if, while operating, it is covered

or comes into contact with ammable material including curtains,

drapery, blankets, etc. KEEP THE FAN HEATER AWAY FROM THESE

MATERIALS.

• Do not connect the fan heater to the power supply until it has been

correctly assembled or positioned.

• Do not run the cable under carpets. Do not cover the cable with blankets,

carpets or similar materials. Place the cable away from busy areas and

where it cannot accidentally be pulled out.

• Do not operate the fan heater in close proximity to bathtubs, showers,

washbasins or pools.

• Do not use the appliance in the bathroom.

• The heating appliance must not be positioned immediately below a

power outlet.

• Do not operate the appliance outdoors.

• Upon initial start-up, the fan heater may emit a slight, harmless smell.

This smell is a normal effect of the initial heating up of the internal

heating elements, and should not recur subsequently.

WARNING: THE ON/OFF SWITCH IS NOT THE ONLY METHOD

OF DISCONNECTING THE MAINS POWER. ALWAYS UNPLUG

THE APPLIANCE DURING MAINTENANCE OPERATIONS, WHEN

MOVING IT OR WHILE IT IS NOT IN USE.

• A fan heater contains parts that generate electrical arcs and sparks. It

must not be used in potentially dangerous areas such as those subject

to the risk of fire or explosion, or areas filled with chemical substances

or humidity.

• Do not use the appliance on soft surfaces such as beds, where the

grilles may get covered. Always rest the fan heater on a flat and stable

surface when it is running, so as to prevent it from toppling. Arrange the

cable so that neither the fan heater or other objects can be on top of it.

V 05/22

DESCRIPTION OF PARTS

• Always unplug the appliance when it is not in use.

• Turn the appliance off if unattended, in order to prevent accidents.

• In the event of any anomalies (abnormal noise or a strange smell),

immediately turn off the appliance; do not attempt to repair it but take

it to your local service centre.

1. Control panel and LED display

2. Air inlet 3. Retractable oscillating base

4. Air outlet

V 05/22

CONTROL PANEL AND REMOTE CONTROLLER

Connect the power cord to an appropriate power outlet (220-240V~/50-60Hz). Press the power button located on

the back of the fan heater.

ON/OFF BUTTON

Touch this button on the control panel or remote control to turn the fan heater on or off.

SWING BUTTON

Touch this button on the control panel or on the remote control to activate the horizontal oscillation of the fan heater, the

corresponding LED lights up on the control panel. To deactivate the swing function, touch this button again.

TIMER BUTTON

Touch the Timer button on the control panel or remote control to select the operating interval in the following circular

sequence 0h (disable Timer), 1h, 2h, 3h ... up to 12 hours. Each time the button is touched, the adjustment interval

will be 1 hour. When the Timer function is activated, the time remaining before shutdown appears on the display. LED

H lights up on the control panel.

MODE BUTTON

Touch this button on the control panel or remote control to select the heating mode in the following circular sequence:

Cool (ventilation mode) - Low (ECO heating mode) - High (COMFORT heating mode)

The corresponding LED lights up on the control panel according to the selected mode.

TEMP BUTTON

Touch this button on the control panel to set the desired temperature from 15 °C up to 40 °C; at each touch the

temperature increases by 1 °C. After setting the temperature, the selected temperature will flash on the display for 3

seconds, then the room temperature will be shown. When the set temperature is reached, the unit automatically goes

into ventilation mode minimizing the air flow.

AUTO FUNCTION: in the absence of a specific mode selection, the Auto function comes into play, which automatically

adjusts the mode and therefore the heat supplied according to the gap between the set temperature and the room

temperature: up to 2 °C of gap, the unit works in ECO mode, beyond the 2 °C difference the unit will work in

COMFORT mode. When the set temperature is reached, the electrical resistance turns off: the unit continues to

ventilate at very low speed to maintain good air diffusion in the room. If, on the other hand, you select the mode, the

unit will operate according to the set mode. On the remote control, press the + (UP) and - (DOWN) keys to set the

temperature. the °C LED lights up on the control panel.

V 05/22

REMOTE CONTROLLER

The functions of the remote control correspond to those on the control panel. When using for the first time, remove the

transparent film applied to the remote control.

Use a Lithium/Manganese button cell, model no. CR2025-3 V, compliant with Battery Directive no. 2006/66 / CE

and amendments by Directive 56/2013/UE

The battery is supplied with the product, on first use remove the plastic tab inserted in the remote control to allow its

operation.

HOW TO INSERT/REMOVE THE REMOTE CONTROL BATTERY (refer to the drawings below)

Open the battery door on the back of the remote control, press the back and pull the right door (A). Insert the battery

in the cover, taking care to check the correct positioning of the polarity (B). Insert the cover into the remote control (C).

WARNINGS FOR BATTERIES

Batteries must not be exposed to heat sources such as fire, sun or similar sources;

Remove the batteries if they start to heat up or you know you will not use the appliance for a long time.

• The batteries must be installed correctly in the appropriate battery compartment;

• When you remove the batteries because they are damaged or at the end of their life, dispose of them according

to the national regulations in force and indicated below.

• In case of battery fluid leak, remove all batteries, avoiding the leaked liquid from coming into contact with skin or

clothes. If liquid from the battery comes into contact with skin or clothing, wash the skin with water immediately.

Before inserting new batteries, carefully clean the battery compartment with a paper towel, or follow the battery

manufacturer’s recommendations for cleaning.

• Warning Danger of explosion if battery is replaced with an incorrect type. Use and replace only batteries with

the same size and type.

Improper use of batteries can cause liquid leakage, overheating or explosion. This liquid is corrosive and can be toxic.

It can cause skin and eye burns, and is harmful to ingest.

To reduce the risk of injury:

• Keep batteries out of the reach of children

• Do not heat, open, puncture, cut or throw batteries into fire

• Do not mix old and new batteries or batteries of different types

• Do not leave metal objects that can come into contact with the battery terminals and therefore can heat up and/

or cause burns.

V 05/22

INFORMATION FOR THE CORRECT DISPOSAL OF BATTERIES IN ACCORDANCE WITH EUROPEAN

DIRECTIVE 2006/66/CE AND CHANGES INTRODUCED BY DIRECTIVE 2013/56 / UE

Replace batteries when they are depleted. At the end of their life, batteries must be disposed of separately

from unsorted waste. They must be taken to designated recycling centres or returned to a retailer providing

this service. Separate disposal of batteries prevents potential negative effects on the environment and

human health due to inadequate disposal, and also allows their constituent materials to be recovered

and recycled, resulting in significant savings in terms of energy and resources. In order to highlight the

obligation regarding separate disposal, the battery carries the crossed-out dustbin symbol. Illegal disposal

of the product by the user may lead to administrative sanctions being applied as per current regulations.

CAUTION: ALWAYS UNPLUG THE APPLIANCE BEFORE CLEANING OR MAINTENANCE OPERATIONS.

IMPORTANT: DO NOT IMMERSE THE CERAMIC FAN HEATER IN WATER

Cleaning the outside surface of the appliance

Use a soft cloth to remove any dust from the fan heater. If the fan heater is excessively dirty, use a soft cloth dampened with water

and neutral detergent at a temperature below 50°C. Leave the fan heater to dry completely before using it again. Do not use

corrosive detergents or solvents such as petrol. Do not wash the appliance with water. When cleaning the appliance, do not use

oils, chemical substances or other items that may damage the surface. Use a vacuum cleaner to remove dust from the air inlet/

outlet grilles.

STORAGE

If the appliance is not used for prolonged periods, it must be stored together with this manual in its original packaging, in a cool

and dry place.

MAINTENANCE AND STORAGE

V 05/22

Model identifier(s): MARGE

Item Symbol Value Unit Item Unit

Heat output Type of heat input, for electric storage local space

Heaters only (select one)

Nominal heat output Pnom 1,8 kW Manual heat charge control, with integrated

Thermostat [no]

Minimum heat output

(indicative) Pmin 1,3 kW Manual heat charge control with room

And/or outdoor temperature feedback [no]

Maximum continuous heat

output Pmax,c 1,8 kW Electronic heat charge control with room

And/or outdoor temperature feedback [no]

Auxiliary electricity

consumption Fan assisted heat output [no]

At nominal heat output elmax 0 kW Type of heat output/room temperature control (select one)

At minimum heat output elmin 0 kW Single stage heat output and no room

Temperature control [no]

In standby mode elsb 0,000 kW Two or more manual stages, no room

Temperature control [no]

With mechanic thermostat room

Temperature control [no]

With electronic room temperature control [yes]

Electronic room temperature control plus

Day timer [no]

Electronic room temperature control plus

Week timer [no]

Other control options (multiple selections possible)

Room temperature control, with presence

Detection [no]

Room temperature control, with open

Window detection [no]

With distance control option [no]

With adaptive start control [no]

With working time limitation [yes]

With black bulb sensor [no]

The seasonal space heating energy efficiency ηs(%) 37

Contact details: ARGOCLIMA SPA - Via A. Varo,35 - Alfianello (BS) - ITALY - www.argoclima.com

INFORMATION REQUIREMENTS FOR ELECTRIC LOCAL SPACE HEATERS

Table 2 - Annex II - Ecodesign requirements - Requirements for product information - COMMISSION REGULATION (EU) 2015/1188

of 28 April 2015 implementing Directive 2009/125/EC of the European Parliament and of the Council with regard to ecodesign

requirements for local space heaterslocale.

V 05/22

www.argoclima.com

Argoclima assumes no responsibility for any errors or inaccuracies in the content of this manual and reserves the right to make any changes to this

manual at any time and without notice, deemed appropriate for any technical or commercial need.

INFORMATION FOR CORRECT DISPOSAL OF THE PRODUCT IN ACCORDANCE WITH THE

EUROPEAN DIRECTIVE 2012/19/EU

At the end of its working life this equipment must not be disposed of as an household waste. It must be

taken to special local community waste collection centres or to a dealer providing this service. Disposing

of electrical and electronic equipment separately avoids possible negative effects on the environment

and human health deriving from an inappropriate disposal and enables its components to be recovered

and recycled to obtain significant savings in energy and resources. In order to underline the duty to

dispose of this equipment separately, the product is marked with a crossed-out dustbin.

Tabla de contenidos

Otros manuales de Calentador de Argo

Manuales populares de Calentador de otras marcas

oventrop

oventrop Regucor Series Manual de usuario

Blaze King

Blaze King CLARITY CL2118.IPI.1 Manual de usuario

ELMEKO

ELMEKO ML 150 Manual de usuario

BN Thermic

BN Thermic 830T Manual de usuario

KING

KING K Series Guía

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Guía de inicio rápido

Well Straler

Well Straler RC-16B Manual de usuario

EUROM

EUROM 333299 Manual de usuario

Heylo

Heylo K 170 Manual de usuario

Eterna

Eterna TR70W Manual de usuario

Clarke

Clarke GRH15 Manual de instrucciones

IRSAP

IRSAP The Radiator Company Ovali Manual de usuario

Empire Heating Systems

Empire Heating Systems WCC65 Manual de usuario

Wetekom

Wetekom 92 86 43 Manual de usuario

Desa

Desa SPC170-F Manual de usuario

Watlow

Watlow Watrod Electric Tubular Heaters Manual de usuario

Haverland

Haverland ECO-DRY GPS Series Manual de lista de piezas

Stelpro

Stelpro ASILVC2060 Series Manual de usuario