ARC LYCT-820 Manual de usuario
Version 2.
pecification:
Function: 2 Channels handy remote control
Frequency: 433.92MHz
Battery: 3V CR2032 Lithium Cell Battery
verview:
Compact in size 5 buttons remote control.
2 sets of ON/OFF button and a ‘All Off’button.
S
O
Wireless Remote Control
LYCT-820
Version 2.
aring:
Pairing using LEARNING MODE:
1. First choose the desired receiver(s) that you wish to control.
2. Press the ‘Learn’ button once (LED will flash), this will now enter learning mode.
3. On the remote control press the ‘ON’ button intended to be paired; the load will flash twice to
confirm that the remote control is now paired.
NOTE: Learning mode lasts for 12 seconds; if no signal is given to the receiver then it will
automatically exit learning mode without pairing the device.
To exit learning mode manually, simply press the ‘Learn’ button again.
！If, during learning mode the load does not flash to confirm, this means that the receiver’s memory
is FULL and no further remote control may be paired unless one of the existing remote control is
first unpaired (see below).
nparing:
Removing single device:
1. With the receiver that you intent to un-pair press the ‘Learn’ button once (LED will flash), this
will now enter learning mode.
2. On the remote control press the ‘OFF’ button intended to be unpaired; the load will flash twice to
confirm that the remote control is now unpaired.
P
U
Version 2.
peration:
ON/OFF Function:
Press the ‘ON’button on remote control, the lights will gradually illuminate.
Press the ‘OFF’button on remote control, the light will gradually turn OFF.
All off' Function:
Press the ‘All off’button on remote control, all lights will gradually turn off.
Dimming Function:
1. Make sure the load is switched ON.
2. On the remote control press the ON button again, the loads will start to dim.
3. To stop at the desired brightness level, press the ON button again.
※Dimming level dims in cycle, during the cycle if no signal is given, after 4 cycles it will stop at
100% brightness.
！After setting a dim level using the remote control the light is then switched OFF, the next time that
the light is switched back ON again the load will return to the previous stipulated brightness.
attery Replacement:
3V CR2032 lithium battery is included.
When the battery voltage is low, the transmission range will be reduced accordingly.
Slide down battery cover and with a screw driver push out the battery.
O
B
Version 2.
Replace with a new battery then slide up the battery cover.
roubleshoot:
Problem: The LED on remote control does not light up.
Solution:Please check if the battery is inserted correctly or replace a new battery.
Problem:I cannot pair my remote control with the receiver.
Solution:The memory on receiver is full, please delete one or more memory and try pairing again.
T
Tabla de contenidos
Otros manuales de Mando a distancia de ARC
ARC
ARC AT401 Manual de usuario
ARC
ARC FLEX Mini M Manual de usuario
ARC
ARC Flex Series Manual de usuario
ARC
ARC Flex ECO Series Manual de usuario
ARC
ARC ECO8S/X Manual de usuario
ARC
ARC PBT-707 Manual de usuario
ARC
ARC MYCT-1702 Manual de usuario
ARC
ARC TMT-918 Manual de usuario
ARC
ARC FLEX EPV Manual de usuario
ARC
ARC FLEX 12EX Manual de usuario
ARC
ARC Flex 2JX Manual de usuario
ARC
ARC ECO Series Manual de usuario
ARC
ARC LYCT-505 Manual de usuario
ARC
ARC FLEX 8EX Manual de usuario
ARC
ARC ECO12S/X Manual de usuario
ARC
ARC FLEXEPH Manual de usuario
ARC
ARC ARC FLEX Manual de usuario
ARC
ARC FLEX6EX Manual de usuario
ARC
ARC ECO4S/X Manual de usuario
ARC
ARC MJLT-2005 Manual de usuario
