AOpen AX47 Hoja de datos

CD-IN Connecto

WOL (Wake on LAN) Connecto

Front Audio Connecto

MODEM-CN Connecto

CNR Expansion Slot

IrDA Connecto

Front Panel Connecto

FDD Connecto

Supports 2nd USB Connecto

JP14 CMOS Clear Jumpe

2Mbit Programmable Flash ROM

Resettable Fuse

478-pin CPU socket (Willamette/

Northwood) with Voltage and Frequency

uto-detection that supports Intel®

Pentium®4 1.3~2.4GHz+ CPU

GP 4x Expansion Slot

32-bit PCI Expansion Slot x5

184-pin DIMM Socket x3 supports

PC-1600/2100 DDR SDRAM

maximum up to 3 GB

VIAApollo P4X266 Chipset that

supports LAN, Ultra ATA/100, DDR

SDRAM Solution

2200μF Low ESR Capacitors

TX Power Connecto

ATA/33/66/100 IDE Connector x2

AUX-IN Connecto

4-pin 12V. ATX Power Connector

Dr. LED Connector(Upgrade Optional)

Onboard AC’97 CODEC

CPU Thermal Sensor

MIC-In

Line-In

Speaker Out

PS/2 Mouse

Connecto

SPP/EPP/ECP Parallel Port MIDI/Game Port

RJ45 10/100

LAN Jack

(Optional)

PS/2 Keyboard

Connecto

USB Port COM 1 Port COM 2 Port

Supports 3rd USB Connecto

Standby LED

FAN3 Connecto

FAN2 and CPU FAN connector

JP17 FSB Select Jumpe

1. JP14 Clear CMOS

Everything you need to boot this

motherboard is included in this

Easy Installation Guide. For more

information, a complete Online

User's Manual can be found in the

Bonus Pack CD Disc. Thanks for

the help of saving our earth.

PART NO: 49.36S01.001 DOC. NO: AX47-EG-E0109A

You can clear CMOS to restore system default setting. To

clear the CMOS, follow the procedure below.

1. Turn off the system and unplug the AC power.

2. Remove ATX power cable from connector PWR2.

3. Locate JP14 and short pins 2-3 for a few seconds.

4. Return JP14 to its normal setting by shorting pin 1 & pin 2.

5. Connect ATX power cable back to connector PWR2.

Tip: When should I Clear CMOS?

1. Boot fail because of overclocking…

2. Forget password…

3. Troubleshooting…

2. JP17 FSB Select Jumper

This jumper allows you to select CPU FSB frequency manually. If you are not an overclocker, we

recommend you keep the default jumper setting.

Motherboard x1

This Easy Installation Guide x1

80-wire IDE Cable x1

Floppy Disk Drive Cable x1

Registration Card x1

Bonus Pack CD x1

NORTON AntiVirus CD x1

Pin 1

133MHz 100MHz

(Default)

Normal

(

default

)

Clear CMOS

1. Pull up the CPU socket lever and up to

90-degree angle.

2. Locate Pin 1 in the socket and look fo

a (golden) cut edge on the CPU uppe

interface. Match Pin 1 and cut edge.

Then insert the CPU into the socket.

3. Press down the CPU socket lever and

finish CPU installation.

Plug in the CPU fan cable to the 3-pin CPU FAN connector. If you have chassis fan, you

can also plug it on System FAN (FAN2) or AUX FAN (FAN3) connector.

This motherboard comes with a 20-pin ATX power connector and an extra 4-pin connecto

as shown below. Make sure you plug in the right direction. We strongly recommend you to

insert the 4-pin connector before connecting the 20-pin connector.

CPU Ratio 8x, 9x, 10x… 21x, 22x, 23x, 24x

CPU FSB (By manual) 100 ~ 200MHz

CPU FSB (By BIOS table) 100, 105, 108, 114, 120 and 123MHz.

CPU CPU Core

Frequency FSB

Clock System

Bus Ratio

Pentium 4 1.3G 1300MHz 100MHz 400MHz 13x

Pentium 4 1.4G 1400MHz 100MHz 400MHz 14x

Pentium 4 1.5G 1500MHz 100MHz 400MHz 15x

Pentium 4 1.6G 1600MHz 100MHz 400MHz 16x

Pentium 4 1.7G 1700MHz 100MHz 400MHz 17x

Pentium 4 1.8G 1800MHz 100MHz 400MHz 18x

Pentium 4 1.9G 1900MHz 100MHz 400MHz 19x

Pentium 4 2G 2000MHz 100MHz 400MHz 20x

Pentium 4 2.2G 2200MHz 100MHz 400MHz 22x

Pentium 4 2.4G 2400MHz 100MHz 400MHz 24x

5. Setting CPU Voltage & Frequency

Setting CPU Core Voltage

This motherboard supports CPU VID function. The CPU core voltage will be automaticall

detected.

Setting CPU Frequency

This motherboard is CPU jumper-less design, you can set CPU frequency through the

BIOS setup, and no jumpers or switches are needed. The default setting is "1MHz

stepping mode", which you can change to "table select mode" by enabling the "Spread

Spectrum" in the bios. so that you can adjust the FSB from "CPU Host/PCI/3V66 Clock"

for overclocking.

3. Installing Processor

Note: If you do not match the CPU

socket Pin 1 and CPU cut edge well, it

may damage the CPU.

CPU socket lever

CPU Pin 1 and cut edge

Note: Some CPU fans do not have

sensor pin so they cannot support fan

monitoring.

CPU Fan Connector

GND

SENSOR +12V

Warning: VIA Apollo

P4X266 Chipset supports

maximum 400MHz

(100MHz*4) system bus

and 66MHz AGP clock;

higher clock setting may

cause serious system

damage.

4. Installing CPU & System Fan

6. Connecting ATX Power Connector

FAN3 Connector

This socket supports Micro-FC-PGA2 package CPU, which is the latest CPU package

developed by Intel. Other forms of CPU package are impossible to be fitted in.

Ground

12V

Ground

Pin1

FAN2 Connector

COM

-5V

+5V

+12V

5VSB

PO-O

COM

+5V

COM

PS-ON

COM

-12V

+3.3V

COM

+5V

COM

GND

+12V

SENSOR

Secondary

Master (3rd)

Secondary

Slave (4th)

Pin 1

Primary

Slave (2nd) Primary

Master (1st)

9. Connecting IDE and Floppy Cables

10. Connecting Front Panel Cable

8. Connect IrDA Connector

The IrDA connector can be configured to support wireless infrared module, with this

module and application software such as Laplink or Windows 95 Direct Cable

Connection, the user can transfer files to or from laptops, notebooks, PDA devices and

printers. This connector supports HPSIR (115.2Kbps, 2 meters) andASK-IR (56Kbps).

Install the infrared module onto the IrDA connector and enable the infrared function

from BIOS Setup, UART mode select, make sure to have the correct orientation when

you plug in the IrDA connector.

Connect 34-pin floppy cable and 40-pin, 80-wire IDE cable to floppy connector FDC and

IDE connector. Be careful of the pin1 orientation. Wrong orientation may cause system

damage.

Pin 1

ATA 33/66/100

IDE Connector

ttach the power LED, speaker, and reset switch connectors to

the corresponding pins. If you enable “Suspend Mode” item in

BIOS Setup, the ACPI & Power LED will keep flashing while the

system is in suspend mode.

Locate the power switch cable from your ATX housing. It is

2-pin female connector from the housing front panel. Plug this

connector to the soft-power switch connector marked SPWR.

Pin 1

FDD Connector

IDE 1 (Primary)

IDE 2 (Secondary)

7. Support Six USB Connectors

This motherboard provides six USB connectors to connect USB devices, such as mouse,

keyboard, modem, printer, etc. There are two connectors on the PC99 back panel. You

can use proper cable to connect other USB connectors to the back panel or front panel of

chassis.

IrDA Connector

SPWR

GND

ACPI LED-

GND

ACPILED

GND

RESET

GND

IDE LED

GND

SPEAKE

Speaker

IDE LED

SPWR

CPI & PWR

LED

Reset

KEY

GND

SBD2+

SBD2-

+5V

GND

SBD3+

SBD3-

+5V

USB2 Connector

IR_TX

+5V

IR_RX

GND

Pin 1

Connector Pin1 Pin2 Pin3 Pin4

AUX-IN Left GND GND Right

MODEM-CN Mono In GND GND Mic Out

CD-IN Left GND GND Right

13. Connecting CD / MODEM / AUX Connector

11. Front Audio Connector

If the housing has been designed with an audio port on the front panel, you’ll be able to

connect onboard audio to front panel through this connector. By the way, please remove

5-6 and 9-10 jumper caps from the Front Audio Connector before connecting the cable.

Please do not remove these 5-6 and 9-10 yellow jumper caps if there’s no audio port on

the front panel.

The AUX-IN connector is used to connect MPEG

udio cable from MPEG card to onboard sound.

The MODEM-CN connector is used to connect

Mono In/ Mic Out cable from internal modem card to

onboard sound circuit.

The CD-IN connector is used to connect CD Audio

cable from CDROM or DVD drive to onboard sound.

UX-IN (Green)

CD-IN (Black)

MODEM-CN (Red)

Pin 1

14. Installing LAN Driver (Optional)

The South Bridge of VIAApollo P4X266 chipset integrates a total communication solution including

10/100Mb Fast Ethernet for Office requirement. You can install LAN Driver under Windows95/98,

98SE, ME and 2000 by following steps.

=====================================

1. Turn on your computer and activate Windows OS. Windows will auto-detect your new adapter

and pop up “New Hardware Found” message.

. Select “Driver from disk provided by hardware manufacturer” to install driver from the diskette

that comes with your LAN adapter.

. Specify the path of the driver in the Bonus CD (i.e. [CD-ROM]:\Driver\LAN\82318233) to copy the

files to your systems.

. When the driver installation is completed, restart Windows.

Note:

1. The NDIS2 and ODI drivers are only supported in Windows95.

. To update the driver in WinME to this version:

a. Right click “My Computer” on desktop, and choose “Property”.

b. Choose “Device Manager” tab, and expand “Network Adapters”

in the device list.

c. Double click the specified network adapter and click “Update

Driver” in tab “Driver”.

d. Choose “Specify the location of the Driver(Advance)”, and then

key in the driver path. (i.e. [CD-ROM]:\Driver\LAN\82318233).

e. WinME will update the driver to this version and prompt the user

to restart windows.

Note: If the Ne

Hardware Found dialo

box does not appear a

startup and you canno

connect to the network,

check the Device

Manager list to see i

the new adapter i

resent. If it is not,

lease install the LA

driver manuall

12. Support 10/100 Mbps LAN onboard (Optional)

Green/ACT

Orange/Speed

The South Bridge V8233 of VIA Apollo P4X266 chipset includes a fast Ethernet controller

on chip. On the strength of SB Integrated MAC+ LSI TQ80223 PHY on board, which is a

highly-integrated Platform LAN Connect device, it provides 10/100M bps Ethernet for

office and home use, the Ethernet RJ45 connector is located on top of USB connectors.

The green LED indicates the link mode, it lights when linking to network and blinking when

transferring data. The orange LED indicates the transfer mode, and it lights when data is

transferring in 100Mbps mode. To enable or disable this function, you may simply adjust it

throu

h BIOS.

GND FRONT L

KEY

FRONT R

VCC

MIC

MIC VREF FRONT R NC

FRONT L

2 10

fter you finish the setting of jumpers and connect correct cables. Power on

and enter the BIOS Setup, press <Del> during POST (Power On Self Test).

Choose "Load Setup Defaults" for recommended optimal performance.

15. Power-on and Load BIOS Setup

16. AOpen Bonus Pack CD 18. BIOS Upgrade

Open Easy Flash is more use

-friendly than traditional flash method. The BIOS binary

file and flash routine are combined together and you simply run a single file to complete

the flash process.

1. Download new BIOS upgrade zipped file from AOpen's web site. For example,

AX47102.ZIP.

2. Run shareware PKUNZIP (http://www.pkware.com) which supports

miscellaneous operation systems to extract the binary BIOS file and the flash

utility. Or Winzip (http://www.winzip.com/) in Windows environment.

3. Save the unzipped file into a bootable floppy disk.

For example, AX47102.BIN & AX47102.EXE

4. Reboot the system to DOS mode without loading any memory handler (such as

EMM386) or device driver. It needs around 520K free memory space.

5. Execute A:> AX47102 and the program will do the rest of it.

DO NOT turn off the power during FLASH PROCESS until you are asked to!!

6. Reboot system and press <Del> to enter BIOS Setup, Choose "Load Setup

Defaults", then “Save & Exit Setup” and finish the BIOS upgrade.

Warning: The upgrade of new BIOS will permanently replace your original BIOS

content after flashing. The original BIOS setting and Win95/Win98 PnP information

will be refreshed and you probably need to re-configure your system.

17. Installing Onboard Sound Driver

You can use the autorun menu of Bonus CD disc. Choose the utility and driver and select

model name.

Del

Warning: Please avoid of using "Load

Turbo Defaults", unless you are sure

our system components (CPU, DRAM,

HDD, etc.) are good enough for turbo

settin

This motherboard comes with a RealTek ALC201 AC97 CODEC, you can find the audio

driver from the Bonus Pack CD disc auto-run menu.

If you encounter any trouble to boot you system, follow the procedures

accordingly to resolve the problem.

Part Number and Serial Number

The Part Number and Serial number are printed on bar code label. You can find this

bar code label on the outside packing, on ISA/CPU slot or on component side of PCB.

For example:

Model name and BIOS version

AX47 R1.02 Sep. 01. 2001 AOpen Inc.

ward Plug and Play BIOS Extension v1.0A

Model name and BIOS version can be found on upper left corner of first boot screen

(POST screen). For example:

AX47 is model name of motherboard; R1.02 is BIOS version

Make sure if the jumper settings for CPU and DRAMs are correct.

Clear CMOS.

Install the VGA card. Then connect your monitor and keyboard.

The problem was probably caused

by power supply or motherboard

failure. Please contact your reselle

or local distributor for repairing.

Perhaps your VGA card or monito

is defective.

Yes

It is very possible that your keyboard

is defective.

During system rebooting, press Del to enter BIOS Setup. Choose

“Load Setup Default".

The problem should be caused by the

IDE cables or HDD itself.

Re-install Windows 95, Windows 98 or Windows NT.

Yes

Turn off the power and unplug the AC power cable, then remove all

of the addon cards and cables, including VGA, IDE, FDD, COM1,

COM2 and Printer.

Turn on the power, and check if

the power supply and CPU fan

work properly.

Start

Check if there is display.

Press Ctrl, and Alt key at the

same time, hold them and then

press Del to see if the

stem reboots.

Turn off the system and

re-connect the IDE cable.

Check if the system can

reboot successfully.

End

P/N: 91.88110.201 is part number, S/N: 91949378KN73 is serial number.

Part No. Serial No.

Dear Customer,

Thanks for choosing AOpen products. To provide the best and fastest service to

our customer is our first priority. However, we receive numerous emails and

hone-calls worldwide everyday, it is very hard for us to serve everyone on time.

We recommend you follow the procedures below and seek help before contact

us. With your help, we can then continue to provide the best quality service to

more customers.

Thanks very much for your understanding!

Open Technical Supporting Team

Online Manual: Please check the manual carefully and make sure the

jumper settings and installation procedure are correct.

http://www.aopen.com.tw/tech/download/manual/default.htm

Test Report: We recommend to choose board/card/device from the

compatibility test reports for assembling your PC.

http://www.aopen.com.tw/tech/report/default.htm

FAQ: The latest FAQ (Frequently Asked Questions) may contain a

solution to your problem.

http://www.aopen.com.tw/tech/faq/default.htm

Download Software: Check out this table to get the latest updated

BIOS/utility and drivers.

http://www.aopen.com.tw/tech/download/default.htm

News Group: Your problem probably had been answered by our support

engineer or professional users on the news group.

http://www.aopen.com.tw/tech/newsgrp/default.htm

Contact Distributors/Resellers: We sell our products through resellers

and integrators. They should know your system configuration very well and

should be able to solve your problem more efficien n important reference for

you if next time you want to buy something else from them.

before contacting us. The part number, serial number and BIOS version

are also very helpful.

Web Site: www.aopen.com

E-mail: Send us email by going through the contact form below.

English http://www.aopen.com.tw/tech/contact/techusa.htm

Japanese http://aojp.aopen.com.tw/tech/contact/techjp.htm

Chinese http://w3.aopen.com.tw/tech/contact/techtw.htm

German http://www.aopencom.de/tech/contact/techde.htm

French http://aofr.aopen.com.tw/tech/contact/techfr.htm

Simplified Chinese http://www.aopen.com.cn/tech/contact/techcn.htm

Pacific Rim

Open Inc.

Tel: 886-2-2696-1333

Fax: 886-2-8691-2233

merica

Open America Inc.

Tel: 1-510-498-8928

Fax: 1-408-922-2935, 1-408-432-0496

Europe

Open Computer b.v.

Tel: 31-73-645-9516

Fax: 31-73-645-9604

Germany

Open Computer GmbH.

Tel: 49-2102-157700

Fax: 49-2102-157799

China

艾尔鹏国际上海(股)

有限公司

Tel: 49-2102-157700

Fax: 49-2102-157799

Tabla de contenidos

Otros manuales de Placa madre de AOpen

AOpen

AOpen MX4GVR Guía de configuración

AOpen

AOpen ATA Manual de usuario

AOpen

AOpen AX4B Pro-533 Guía de configuración

AOpen

AOpen AK77-400 Guía de configuración

AOpen

AOpen MX4SGI-4DN2 Guía de configuración

AOpen

AOpen AK75PRO Hoja de datos

AOpen

AOpen AK79G MAX Hoja de datos

AOpen

AOpen AX63 Guía de configuración

AOpen

AOpen AX45 PRO-533 Guía de configuración

AOpen

AOpen AX4GE Tube Guía de configuración

AOpen

AOpen AK77-8X Guía de configuración

AOpen

AOpen AX4B-533 Tube Hoja de datos

AOpen

AOpen 1AK79G-V Guía de configuración

AOpen

AOpen s760GXm-US Manual de usuario

AOpen

AOpen AX4T 2-533 Hoja de datos

AOpen

AOpen S661FXM-US Manual de usuario

AOpen

AOpen AK73 Series Guía de configuración

AOpen

AOpen AK89 MAX Hoja de datos

AOpen

AOpen MX46U2-VN Hoja de datos

AOpen

AOpen MX4SG-4DL Hoja de datos

AOpen

AOpen MX4BS Hoja de datos

AOpen

AOpen MK33IIA Manual de usuario

AOpen

AOpen MX4SGI-4DN Guía de configuración

AOpen

AOpen MX4LR TV Manual de usuario

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario