Antec P193 Manual de usuario
P193
U
SER
’
S
M
ANUAL
1
T
ABLE OF
C
ONTENTS
I
NTRODUCTION
1.1 Case Specifications.…..………………………………………………………………………………….. 3
1. Diagram…………………………………………………………………….…………………………………. 3
H
ARDWARE
I
NSTALLATION
G
UIDE
.1 Setting Up….…………………………………………………………………………………………………. 4
. Power Supply Installation……………………………………………………………………………… 4
.3 CP Series Power Supply Mount…………………………………………………………………….. 5
.4 Cable Management………………………………………………………………………………………. 5
.5 Motherboard Installation..……………………………………………………………………………. 5
.6 Internal 3.5” Device Installation……………………………………………………………………. 6
.7 External 3.5” Device Installation…………………………………………………………………… 7
.8 External 5. 5” Device Installation…………………………………………………………………. 7
C
ONNECTING THE
F
RONT
I/O
P
ORTS
3.1 USB .0 Ports………………………………………………….……………………………………………. 8
3. eSATA Ports…………………………………….……………………………………………………………. 8
3.3 AC’97 / HD Audio Ports……………………….………………………………………………………… 8
3.4 Switch and LED Connectors…………………………………………………………………………… 9
3.5 Rewiring Motherboard Header Connections………………………………………………… 9
C
OOLING
S
YSTEM
4.1 TriCool™ Fans ………………………………………………………………………………………………. 10
4. Optional Fans.………………………………………………………………………………………………. 11
4.3 Washable Air Filters………………………………………..……………………………………………. 1
P193
U
SER
’
S
M
ANUAL
At Antec, we continually refine and improve our products to ensure the highest quality. It’s possible
that your new case will differ slightly from the descriptions in this manual. As of the date of
publication, all features, descriptions, and illustrations in this manual are correct.
Dis
c
laim
er
This manual is intended only as a guide for Antec’s computer enclosures. For more comprehensive
instructions on installing the motherboard and peripherals, please refer to the user’s manuals that
come with those components.
The P193 does not come with a power supply unit (PSU). Make sure you choose a power supply that is
compatible with your computer components and has a long enough power harness to reach your
motherboard and peripheral devices. We recommend our CP Series, TruePower Series or Signature
Series power supplies for the latest ATX specification compliance, broad compatibility, and energy-
saving capability.
Although care has been taken to prevent sharp edges in your Antec case, we strongly recommend
taking the appropriate time and care when working with it. Avoid hurried or careless motions. Please
use reasonable precaution.
This manual is not designed to cover CPU, RAM, or expansion card installation. Please consult the
motherboard manual for specific mounting instructions and troubleshooting. Before proceeding,
check the manual for your CPU cooler to find out if there are steps you must take before installing the
motherboard. While installing hardware, keep your case on a flat, stable surface.
3
1.1 C
ASE
S
PECIFICATIONS
Case Type
Advanced Mid Tower
Color
Gunmetal Gray
Dimensions
514mm (H) x 05mm (W) x 590mm (D)
0. 5" (H) x 8.1" (W) x 3. 5" (D)
* Actual clearance for width is 9.5”/ 41mm due to the side panel fan
Weight
35.8 lbs / 16. 5 kg
Cooling
-
1
x Rear 1 0mm TriCool
™
exhaust fan
- x Top 140mm exhaust TriCool™ fan
-1 x Side 00mm Big Boy 00™ fan for dual video cards
-1 x Lower (optional) chamber 1 0mm TriCool™ fan
-1 x Front (optional) 1 0mm fan mount for HDD
-1 x Middle (optional) 1 0mm fan mount for video cards
Drive
Bays
11 Drive Bays:
-4 x External 5. 5” drive bays
-1 x External 3.5” drive bay
-6 x Internal 3.5” drive bays
Expansion Slots 7
Motherboard Size
Mini-ITX, microATX, Standard ATX, Extended ATX
Front I/O Panel
x USB .0
1 x eSATA
AC’97 / HD Audio In and Out
1.
D
IAGRAM
1. Rear 1 0mm TriCool™ fan
. Top 140mm TriCool™ fans
3. 00mm side Big Boy 00™ fan
4. Washable air filters
5. Motherboard mount
6. Power supply mount
7. 5. 5” drive bays
8. 3.5” hard drive bays
9. Front I/O panel
4
H
ARDWARE
I
NSTALLATION
G
UIDE
.1
S
ETTING
U
P
1. Place the case upright on a flat, stable surface with the
rear of the case facing you.
. Remove the thumbscrews from the right side panel.
Grip the panel at the top and bottom and slide it toward
you to open the case.
3. Remove the screws from the left side panel. Grip the
panel at the top and bottom and slide it toward you to
remove the left side panel.
Note: Do not use your fingernails to pry or lift the
panels.
Inside the case you should see two separate chambers: the upper chamber for the motherboard,
externally accessible drives and hard drives; and the lower chamber for the power supply and hard
drives. You will also find some wiring with marked connectors (USB, PWR, etc.), the installed I/O panel,
a box containing one set each of drive rails for a 5. 5” drive and a floppy disk drive, and a tool box
attached to the upper HDD cage containing more hardware (screws, brass standoffs, spare silicone
grommets, etc.).
.
P
OWER
S
UPPLY
I
NSTALLATION
Most power cables can be routed behind the motherboard through the cable management
compartment. If some cables can’t reach, run them through the passage that goes straight into the
motherboard compartment.
1. Remove both side panels.
. If you are installing an Antec CP series power supply, you will need to
remove the PSU adapter plate.
3. Slide the power supply into the case. If not routing cables through the
cable management compartment behind the motherboard, route
cables through the covered opening. This will save a few inches of
cable travel and help improve airflow in the power supply
compartment.
Note: Power supplies with fans on the bottom will need to be
mounted so that the fan is facing the top of the case. There are
mounting holes for power supplies to be installed upside up or
upside down.
4. Secure the power supply by fastening it to the back of the case with
the provided screws.
5
.3
CP
S
ERIES
P
OWER
S
UPPLY
M
OUNT
Your Antec P193 enclosure
comes with a power supply mounting
adapter to mount either a standard-size power supply or the unique
Antec CP Series high-performance power supply. This adapter is
mounted to the chassis with standard Phillips-head screws. In order to
install the CP Series power supply, remove the mounting plate first.
.4
C
ABLE
O
RGANIZERS
There is a cable management compartment between the motherboard and right side panel. You can
tuck or route excess cables in this compartment.
1. Remove both side panels.
. Choose the cables you would like to pass through the holes behind the motherboard tray and pull
them out of the power supply chamber toward the right side of the case.
3. Use the cable ties provided to hold them in place.
4. Feed the cables back through the insertion point nearest the destination of the cable. Connect the
cable and then pull the slack back to the right side of the case.
.5
M
OTHERBOARD
I
NSTALLATION
1. Lay the case down, with the open side facing up. The
drive cages and power supply should be visible.
. Make sure you have the correct I/O panel for your
motherboard. If the panel provided with the case isn’t
suitable, please contact your motherboard
manufacturer for the correct I/O panel.
3. Align your motherboard with the standoff holes and
remember which holes are lined up. Not all
motherboards will match with all the provided holes;
this is normal and won’t affect its functionality.
4. Remove your motherboard by lifting it up.
5. Install standoffs as needed and put the motherboard
back in.
6. Screw in your motherboard to the standoffs with the
provided Phillips-head screws.
6
.6
I
NTERNAL
3.5”
D
EVICE
I
NSTALLATION
With the front bezel facing you, swing the front door open. It can swing 70º so the door is parallel with
the side of the case. You can see there are four 5. 5” and one 3.5” external drive bays. Inside the case
there are two 3.5” drive cages, which can house up to six hard drives.
Note: We recommend using the lower HDD cage to maximize cooling and quiet computing.
Upper HDD Installation
1. Remove the thumbscrew holding the upper HDD cage.
. Pull the HDD cage from its position by pulling the ring toward you.
3. There are two HDD trays inside the cage. Squeeze the metal clips on each side of the tray and slide
the tray out.
4. Mount your hard drive into the drive tray with the special screws provided. Don’t over-tighten the
screws as this will reduce the vibration and noise dampening ability of the silicone grommets.
Note: Always mount the HDD with the thicker side of the silicone grommets facing up.
5. Slide and lock the tray back into the cage.
6. Slide the cage back into the case and fasten the thumbscrew.
7. Find the right Molex or SATA connector on the power supply and connect it to the hard drive.
8. Repeat the same procedure for the other drives.
Lower HDD Installation
1. Remove the thumbscrew holding the lower HDD cage.
. Pull the HDD cage from its position by pulling the ring towards
you.
3. You can mount up to four hard drives inside the cage. They are
mounted vertically with the silicone grommets sitting at both
sides.
4. Mount your hard drive into the drive cage with the special screws
provided. Don’t over-tighten the screws as this will reduce the
vibration and noise dampening ability of the silicone grommets.
Note: Always mount the HDD with the thicker side of the silicone
grommets facing up.
5. Slide the cage back into the case and fasten the thumbscrew.
6. Find a Molex or SATA connector on the power supply and connect
it to the hard drive.
7
.7
E
XTERNAL
3.5”
D
EVICE
I
NSTALLATION
There is one external 3.5” drive bay.
1. Carefully remove the plastic drive bay cover and metal plate covering the drive bay.
. Find a pair of 3.5”drive rails in the hardware kit box.
3. Mount the drive rails onto the sides of the 3.5” device. Make sure the metal portion is angled on
the outside and facing forward.
4. Slide the device into the drive bay until it clicks into place.
5. Connect a small 4-pin connector from the power supply to the 4-pin connector on the floppy drive.
.8
E
XTERNAL
5. 5”
D
EVICE
I
NSTALLATION
There are four 5. 5” drive bays and 8 drive rails.
1. Carefully remove the plastic drive bay cover / filter and metal
plate covering the drive bay.
. Mount the drive rails onto the sides of the 5. 5” device. Make
sure the metal portion of the rail faces the front of the drive.
3. Slide the device into the drive bay until it clicks into place.
4. Mount the other devices accordingly.
5. Connect the appropriate Molex or SATA power connector from
the PSU to the power connector on the device.
8
Pin
Signal
Names
Pin
Signal
Names
1
USB
Power
1
2
USB
Power
2
3
Negative Signal
1
4
Negative Signal
2
5
Positive Signal
1
6
Positive Signal
2
7
Ground
1
8
Ground
2
9
Ke (No Connection)
1
0
Empt
Pin
Pin
Signal
Names
(HDA)
Pin
Signal
Names
(AC
’
97)
1
MIC2
L
1
MIC In
2
AGND
2
GND
3
MIC2
R
3
MIC Power
4
AVCC
4
N
C
5
FRO-R
5
Line
Out
(R)
6
MIC2_JD
6
Line
Out
(R)
7
F_IO_SEN
7
N
C
8
Ke (no pin)
8
Ke (no pin)
9
FRO-L
9
Line
Out
(L)
10
LINE2_JD
10
Line
Out
(L)
C
ONNECTING THE
F
RONT
I/O
P
ORTS
3.1
USB
.0
Connect the front I/O panel USB cable to the USB header pin on your motherboard. Check the
motherboard manual to ensure that it matches the table below:
3.
E
SATA
You will find a SATA connector on a cable attached to the front ports. This internal SATA connector is
designed to connect to a standard SATA connector on your motherboard. This will allow high-speed
external hard disk enclosures such as the Antec MX-1 to run at the same speeds as internally installed
hard disks.
3.3
AC'97
/
HD
A
UDIO
P
ORTS
There is an Intel® standard 10-pin AC’97 connector and an Intel® 10-pin HDA (High Definition Audio)
connector linked to the front panel of the case.
10
6
4
9
7
5
3
1
You can connect either the AC’97 or the HDA connector, depending on the model of the motherboard.
Locate the internal audio connectors from your motherboard or sound card and connect the
corresponding audio cable. Consult your motherboard or sound card manual for the pin-out positions.
Even if your system supports both audio standards, you may only use one connector.
1
9 10
9
3.4
S
WITCH AND
LED
C
ONNECTORS
Connected to your front panel are LED and switch leads for power,
reset, and HDD LED activity. Attach these to the corresponding
connectors on your motherboard. Consult your motherboard
manual for specific pin header locations. For LEDs, colored wires
are positive ( + ). White or black wires are negative ( – ). If the LED
does not light up when the system is powered on, try reversing the
connection. For more information on connecting LEDs to your
motherboard, see your motherboard manual.
Note
:
Polarity (positive and negative) does not matter for switches.
3.5
R
EWIRING
M
OTHERBOARD
H
EADER
C
ONNECTIONS
There may come a time when you need to reconfigure the pin-out of a motherboard header connector.
Examples could be for your USB header, audio input header, or some other front panel connector such
as the Power Button connector. Before performing any work, please refer to your motherboard manual
or your motherboard manufacturer's website to be sure of the pin-out needed for your connector. We
strongly recommend making a notated drawing before beginning work so that you can recover if your
work gets disturbed.
1. Determine which wires you need to remove inorder to rewire your
plug to match the USB pin-outs on your motherboard (refer to your
motherboard manual). Working on one connector at a time, use
a very small flathead screwdriver or similar tool to lift up on the black
tab located beside the gold posts (squares). This will allow you to
easily slide out the pins from the USB plug.
. Working carefully so as not to damage the wires, connectors, or pins,
slowly remove the pin from the connector. Repeat these steps for
each wire you need to change.
3. Working carefully so as not to damage the wires, connectors or pins,
slowly reinsert the pin into the correct slot of the connector, then
snap closed the black tab that was lifted in Step 1.
Otros manuales de Recinto de Antec
Antec
Antec Dark fleet DF-10 Manual de usuario
Antec
Antec NSK6500 Manual de usuario
Antec
Antec Nine Hundred Two Manual de usuario
Antec
Antec Ruby / Sapphire Manual de usuario
Antec
Antec NSK 3300 Manual de usuario
Antec
Antec Solution SLK3700AMB User’s Manual de usuario
Antec
Antec Performance 1 Silent Manual de usuario
Antec
Antec VERIS MX-100 Manual de usuario
Antec
Antec P183 Manual de usuario
Antec
Antec Veris Fusion Remote Max Manual de usuario
Antec
Antec VERIS MX-1 Manual de usuario
Antec
Antec SX1240 Manual de usuario
Antec
Antec Veris Fusion Remote Black Guía de inicio rápido
Antec
Antec Quiet Computing Mini Skeleton-90 Manual de usuario
Antec
Antec Fusion Remote Max Manual de usuario
Antec
Antec Mini P180 White Manual de usuario
Antec
Antec SLK3800B Manual de usuario
Antec
Antec Veris Fusion 430 Guía del usuario
Antec
Antec GX300 Manual de usuario
Antec
Antec SONATA IV Manual de usuario
