Antari W-715 Manual de usuario

W-715 Fog Jet

USER MANUAL

2013 Antari Lighting and Effects Ltd.

English

Safety Information

Please read the following safety information carefully before operating the

machine. Information includes important safety information about installation,

usage, and maintenance. Pay attention to all warning labels and instructions in

this manual and printed on the machine.

If you have questions about how to operate the machine safely, please contact your local

Antari dealer for help.

Keep this device dry.

Always connect to a grounded circuit to avoid risk of electrocution.

Before connecting machine to power, always check voltage indicate on machine match

to your local AC voltage. Do not use the machine if AC power voltage does not match.

Disconnect the machine from AC power before servicing and when not in use.

This product is for indoor use only! Do not expose to rain or moisture. If fluid is spilled,

disconnect AC power and clean with a damp cloth. If fluid is spilled onto electronic parts,

immediately unplug the machine and contact your local Antari dealer for advice.

No user serviceable and modifiable parts inside. Never try to repair this product,

unauthorized technician may lead machine to damage or malfunction.

For adult use only. Never leave the machine running unattended.

Installed in well ventilated area. Provide at least 50 cm space around the machine.

Never add flammable liquid of any kind to the machine.

Make sure there are no flammable materials close to the machine while operating.

Only use Antari fluid. Other fluid may lead to heater clog and malfunction.

If the machine fails to work, unplug the machine and stop operation immediately.

Contact your local Antari dealer for advise.

Before transporting the machine, make sure the fluid tank is completely drained.

Smoke fluid may present health risks if swallowed. Do not drink smoke fluid. Store it

securely. In case of eye contact or if fluid is swallowed immediately look for medical

advice.

Unpacking and Inspection

Immediately upon receiving the machine, carefully unpack the carton, check all content to

ensure that all parts are present and have been received in good condition. If any parts

appear damaged or mishandled from shipping, notify the shipper immediately and retain the

packing material for inspection.

What is included: 1 x W-715 Fogger

1 x Power Cord

1 x User Manual

1 x W-1 Wireless Transmitter (excluded in W-715X)

Product Overview

Setting Up

Step 1: Place the machine on a flat surface and in a suitable large area with at least 50 cm

open space at each side of the machine and 5 meters for the output direction of the

machine.

Step 2: Fill the fluid tank with Antari FLC fog fluid.

Step 3: Connect the machine to suitable rated power supply. To determine the power

Wireless Receiver

DMX 3Pin

DMX 5Pin

Power Inlet

Breaker

LCD Control Panel

Handle

Tank Cap

（Group）

Smoke Output Nozzle

requirement for the machine refer to the label on the back of the machine.

Always connect the machine to a protected circuit and ensure it is properly

grounded to avoid risk of electrocution.

Step 4: Turn on the machine by connecting the power cord and turning the Neutrik

Powercon. Heat up takes approximatly 9 minutes. Once the machine has reached operating

temperature, the LCD screen will display “Ready To Fog”. Now the machine is ready for

operation.

Step 5: To turn off the machine, turn the Neutrik Powercon again.

Language Setting

To switch the language used for control interface, press [Menu] button BEFORE turning on

the machine and HOLD it until LCD screen flashes for two times. After the two flashes, press

[Menu] to choose the language: English and 中文 (Chinese).

Operation

Control Panel

The machine can be operated with the LCD control panel located on top of the fogger.

Button

Function

[Menu]

Select from functions

[▲/ Timer]

To increase value or choose from options

To activate Timer Mode

[▼/ Volume]

To decrease value or choose from options

To active Volume Mode

To emit fog under 2-Second Jet Mode

[Stop]

To stop output or go back to main screen

Functions

Value

Description

Interval Set

10-300 Seconds

Interval time under Timer Mode

Duration Set

2-15 Seconds

Duration time under Timer Mode

Timer Output

50-100%

Output volume under Timer Mode

Volume Output

50-100%

Output volume under Volume Mode

2-Second Jet Mode

On/Off

Activate or disactivate 2-Second Jet Mode

DMX512 Address

1-512

Setup the DMX address

Wireless Control Mode

On/Off

Activate or disactivate Wireless Control Mode

Quick Start Mode

On/Off

Activate or disactivate Quick Start Mode

Timer Operation

To operate the machine under Timer Mode, interval, duration time and output volume under

Timer Mode must be set first:

Interval Time Setup - Press [Menu] button until LCD screen displays “Interval Set”and then

press ▲or ▼button to set the interval time from 10-300 seconds.

Duration Time Setup - Press [Menu] button until LCD screen displays “Duration Set”and

press ▲or ▼button to set the duration time from 2-15 seconds.

Output Volume Setup - Press [Menu] until LCD screen displays “Timer Output”and press ▲

or ▼button to set the output percentage from 50-100%.

After finishing the above setting, go back to main screen by pressing [Stop] button.

To activate Timer Mode, press [Timer] button under main screen. To deactivate Timer

Mode, press [Stop] button.

Volume Operation

To operate the machine under Volume Mode, output volume under Volume Mode must be

set first:

Output Volume Setup - Press [Menu] button until LCD screen displays “Volume Output”and

then press ▲or ▼button to set the output percentage from 50-100%.

After finishing the above setting, go back to main screen by pressing [Stop] button.

To activate Volume Mode, press [Volume] button under main screen. To deactivate

Volume Mode, press [Stop] button.

Note: Under Volume Mode, fogger emits fog continuously until a re-heat is needed.

2-Second Jet Operation

To activate 2-Second Jet Mode, press [Menu] button until LCD screen displays “2-Second

Jet Output”and then press ▲or ▼button to activate or deactivate 2-Second Jet Mode.

Once the 2-Second Jet Mode is activated, the main screen will keep showing “2-Sec Jet

Mode. Press [Volume] button and the fog will be emitted for 2 seconds with maximum output

(100%).

DMX Operation

Making the DMX Connection –Connect machine to a DMX controller or to one of the

machines in the DMX chain. The machine uses an 3-pin and 5-pin XLR connector for DMX

connection, the connector is located on the rear of the machine.

Address Setup –Press [Menu] until LCD screen displays “DMX512 Add:”and then press ▲

or ▼button to set the DMX address from 1-512.The machine occupies 1 control channel.

The starting address is defined as the first channel from which the machine will respond to

the controller. Always double check to make sure there are no overlapping channles in order

to control the machine correctly.

DMX Channel Function

Channel

DMX Value Range

Function

0–5

Fog Off

6–255

Fog Output 50 –100%

Fog Output 100% for 2 seconds

(under 2-Second Jet Mode)

DMX Connector Pin Assignment

The machine provide 3 or 5 pin XLR connector for DMX connection. Diagram below indicate

pin assignment information

Function

Ground

Data-

Data+

Wireless Remote Control Operation (Not applicable for W-715X)

The wireless remote control system consists of a transmitter equipped with two buttons for

on and off functions and a receiver pre-attached to the rear of the machine.

*Transmitter

With the transmitter it is possible to emit fog via radio signal at maximum distance of 50

meters. Press the button “A”or “B”, to emit fog.

*Receiver

The receiver is tested and pre-attached to the rear of the machine. The included transmitter

has been registered to the machine before shipping.

To activate or deactivate the wireless remote control function, press [Menu] until LCD

displays “Wireless”and press ▲or ▼button to activate or deactivate the wireless remote

control function. When wireless remote control function is activated, the LCD screen will

display “Wireless Detect …” for 15 seconds, and during this 15-second time, wireless

transmiter(s) must be registered by pressing either button A or B on the transmitter(s). The

pressed button A or B while registering will be the button to emit fog under wireless remote

control mode.

Note:

1. Once wireless remote control function is activated, a “W”sign will be displayed on the

LCD screen.

2. Once wireless remote control function is activated, the LCD screen will display “Wireless

Detect …” everytime when the machine is turned on; this allows new registration. Every

new registration overwrites the previous memory.

3. One machine can be controlled by up to 5 transmitters while one transmiter can be

registered to unlimited machines.

4. Battery used in transmiter: type A27S 12V.

5. When under 2-Second Jet Mode, pressing the button (A or B) on the trasmitter will emit

fog for 2 seconds with maximium output (100%).

Power Saving

Keep pressing [Stop] button for 3 seconds, LCD screen will display the countdown of 60

seconds. After the countdown, the machine will go into sleep mode. To wake the

machine again, press any button.

When the machine is idle for 15 seconds, the backlight of the LCD screen becomes dim.

To light up again the LCD screen, press any button.

When DMX connector is disconnected from the machine, the machine will go into sleep

mode, and when DMX connector is re-connected to the machine again, the machine will

be waked up.

Liquid

Only use Antari FLC water-based liquid for the W-715 Fogger. The machine is tested and

calibrated with this liquid to get the best output performance. Warranty will be void if any

other type of liquid is used, improper use of liquid may lead to machine failure and

malfunction.

Service and Maintenance

Do not allow the machine to become contaminated.

Remove dust from air vents with air compressor, vacuum or a soft brush.

Only use a damp cloth to clean the casing.

Before storing run distilled water through the system to help avoid condensing the pump

or heater.

It is recommended to run the machine on a monthly basis in order to achieve best

performance and output condition.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Máquina de niebla de Antari

Antari

Antari F-6 Manual de usuario

Antari

Antari F-3 Fazer Manual de usuario

Antari

Antari W-508 Manual de usuario

Antari

Antari Z-1500II Manual de usuario

Antari

Antari FT-100 Fire Training Manual de usuario

Antari

Antari F-1 Fazer Manual de usuario

Antari

Antari 20210616 Manual de usuario

Antari

Antari FT-50 Manual de usuario

Antari

Antari X-510PRO Manual de usuario

Antari

Antari HZ-300 Manual de usuario

Antari

Antari AF-5X Manual de usuario

Antari

Antari F-450 Manual de usuario

Antari

Antari FT-100 Fire Training Manual de usuario

Antari

Antari MOBILE MB-55 Manual de usuario

Antari

Antari Fog cooler DNG-100 Manual de usuario

Antari

Antari Z-1000II Manual de usuario

Antari

Antari FT-20 Manual de usuario

Antari

Antari ICE-101 Manual de usuario

Antari

Antari Fazer X-310 PRO Manual de usuario

Antari

Antari Z Series Manual de usuario

Antari

Antari X-310PRO Manual de usuario

Antari

Antari Onboard DMX Manual de usuario

Antari

Antari Ip-1000 Manual de usuario

Antari

Antari HZ-500 Manual de usuario

Manuales populares de Máquina de niebla de otras marcas

Boost

Boost BOOST-FOG400LED-BK Manual de usuario

Home Accents Holiday

Home Accents Holiday FM1000-ASH Manual de usuario

EuroLite

EuroLite ZEITGEIST FOG-1200 Manual de usuario

Dyna-Fog

Dyna-Fog CYCLONE ULTRA 2734 Manual de usuario

PROEL

PROEL DRAGO HEAVY PLFD150HY Manual de usuario

Sparklyn

Sparklyn Y846 Manual de usuario

Magicfx

Magicfx CO2 Gun Manual de usuario

Ibiza

Ibiza LSM500LAS Manual de usuario

Venue Lighting Effects

Venue Lighting Effects ULTRA MINI-FOGGER Manual de usuario

High End

High End F-100 Manual de usuario

Chauvet

Chauvet ARENA 2100 FLEX Manual de usuario

Beamz

Beamz F1600 Manual de usuario

Sagitter

Sagitter SG ARS900C Manual de usuario

KISANKRAFT

KISANKRAFT KK-STF-480 Manual de usuario

Orion

Orion OT-U250PP Guía

Beamz

Beamz S2500 Manual de usuario

American DJ

American DJ Dyno-Fog II Manual de usuario

JB Systems

JB Systems FX 1700 Manual de usuario