Antari ICE-101 Manual de usuario

ICE-101

Low Fog Machine User Manual

BODENNEBLER B

English Français Deutsch • • • 中文

User Manual

Antari ICE Low Fog Machine

Congratulations on the purchase of your new

ANTARI FOG MACHINE.

Introduction

Thank you for choosing an ANTARI Fog Machine. You now own a rugged and powerful

state-of-the-art machine. Prior to use, we suggest that you carefully read all of the

instructions. By following the suggestions found in this user manual, you can look forward to

the reliable and satisfactory performance of your ANTARI Fog Machine for years to come.

Please follow these operation, safety and maintenance instructions to

ensure a long and safe life for your fog machine.

Cautions

Risk of electric shock. Disconnect the appliance from the electric supply before

removing the cover. Note: there are no user serviceable parts inside.

Danger of electric shock

♦Keep this device dry.

♦For inside use only. Not designed for outside use.

♦For the 110V models, use 3-prong grounded electrical outlet only. Prior to use take care to

determine that the unit is installed at the rated voltage.

♦Always unplug your ANTARI Fog Machine before filling its tank.

♦Keep fog machine upright.

♦Turn off or unplug when not in use.

♦This machine is not water- or splash-proof. If moisture, water, or fog liquid gets inside the

housing, immediately unplug the unit and contact a service technician or yourANTARI

dealer before using it again.

♦No user serviceable parts inside. Refer to yourANTARI dealer or other qualified service

personnel.

Danger of burns

♦For adult use only. Fog machine must be installed out of the reach of children. Never leave

the unit running unattended.

♦Never aim the output nozzle directly at people.

♦Fog machine output is very hot. Avoid coming within 60 cm of the output nozzle during

operation.

♦Locate the fog machine in a well-ventilated area. Never cover the unit’s vents. In order to

guarantee adequate ventilation, allow a free air space of at least 20 cm around the sides

and top of the unit.

♦Never aim the output nozzle at open flames.

♦The output nozzle becomes very hot during operation (300°C). Keep flammable materials

at least 50 cm away from the nozzle.

♦Always allow your ANTARI Fog Machine to cool down before attempting to clean or service

it.

Danger of explosion

♦Never add flammable liquids of any kind (oil, gas, perfume) to the fog liquid.

Pay attention to all warning labels and instructions printed on the exterior of your ANTARI

Fog Machine

♦Use only the high-quality, water-based fog liquid that your dealer recommends. Other fog

liquids may cause clogging or “spitting”.

♦Always make sure there is sufficient liquid in the fog liquid tank. Operating this unit ithout

liquid will cause damage to the pump as well as over-heating of the heater.

♦If your ANTARI Fog Machine fails to work properly, discontinue use immediately. Drain all

fog liquid from the tank, pack the unit securely (preferably in the original packing material),

and return it to your ANTARI dealer for service.

♦Always drain tank before mailing or transporting this unit.

♦Never drink fog liquid. If it is ingested, call a doctor immediately. If fog liquid comes in

contact with skin or eyes, rinse thoroughly with water.

Unpacking & Inspection

Open the shipping carton and verify that all equipment necessary to operate the system has

arrived intact. Refer to the “Features” section for information on what items are included with

your model. If any equipment is missing contact your ANTARI dealer immediately.

Before beginning initial setup of your ANTARI Fog Machine, make sure that there is no

evident damage caused by transportation. In the event that the unit’s housing or cable is

damaged, do not plug it in and do not attempt to use it until after contacting your ANTARI

dealer for assistance.

Setup

♦Remove all packing materials from shipping box. Check that all oam and plastic padding is

removed, specially in the nozzle area.

♦Place fog machine on a flat surface and remove fog liquid tank cap.

♦Fill with ANTARI Fog Liquid or other high-quality water-based fog fluid. Any other types of

fluid can damage the unit. When filled, place cap back on liquid tank.

♦Fill the chamber with regular ice cubes or dry ice. The chamber can hold as much as 8 kg

ice cubes.

♦When the chamber is filled, gently put the cover back. Tighten the cover with appropriate

force only.

♦Firmly attach the included tube to the drainage outtake. Place the end of the tube to a

container.

♦Firmly attach the remote control cable to the proper input on the rear of the machine.

Operation

♦Plug power cord into a grounded electrical outlet. If necessary, turn power switch on rear of

unit to “ON” position. Warm-up is complete when green lamp lights up on remote unit.

♦To emit fog, press the appropriate button on the remote for the desired length of time.

♦The remote unit’s lamp will cycle on and off as the machine re-heats to the proper

operating temperature.

♦DANGER OF LEAKAGE! The water tank must regularly be drained.

♦For further information on operating your ANTARI Fog Machine, see the section titled,

“Remote Control Operation”.

If your model includes a mounting bracket designed for overhead installation, it may be

installed at floor level or suspended overhead. If the unit is to be mounted using the bracket,

it is important that the fog does not shoot directly at any one’s face. Whatever installation

method you choose, do not allow the unit to have more than a 15 degree angle of inclination.

Important: Always monitor tank fluid level as you are fogging. Running a fog machine with

no fluid can permanently damage the unit.

If you experience low output, pump noise or no output at all, unplug immediately. Check fluid

level, the external fuse, remote connection, and power from the wall. If all of the above

appears to be O.K., plug the unit in again. If fog does not come out after holding the remote

button down for 30 seconds, check the hose attached to the tank to make sure there is fluid

going through the hose. If you are unable to determine the cause of the problem, do not

simply continue pushing the remote button, as this may damage the unit. Return the

machine to your ANTARI dealer.

Remote Control Operation:

Z-8: 25 feet wired multi-function remote control with 4-PIN XLR connector for ANTARI

ICE-101.

․Interval knob: Rotate it to set the interval time between fog outputs in the Timer

mode. The range is from 10 to 250 seconds.

․Duration knob: Rotate it to set the duration time of fog output in the Timer mode.

The range is from 1 to15 seconds.

․Output knob: Rotate it to set the volume of fog output. The range is from 0% - 100%

of maximum output.

․To press the yellow Timer button can activate Timer mode.

․To press the red Continuous button can make the machine generate fog output

constantly. The fog output is set by Output knob. Please note that when the

temperature of heater is too low, the machine stops producing fog and starts to

reheat. Once the reheating process is completed, the machine can continue to

produce fog output.

․To keep pressing the green Manual button can make the machine generate fog at

maximum volume. Once Manual button is released, the fog output stops

immediately.

Cleaning your fog machine regularly will help reduce costly parts

replacement and repair charges.

Maintenance

Do not allow the fog liquid to become contaminated. Always replace the caps on the fog

liquid container and the fog machine liquid tank immediately after filling.

After every 40 hours of continuous operation, it is recommended to run distilled water

through the system to prevent the accumulation of particles in the heating element. The

recommended cleaning steps are as follows:

1. Empty fog fluid from fluid tank. Add distilled water to tank.

2. Plug in and allow machine to finish heating-up process.

3. Run the machine in a well-ventilated area for a few minutes.

4. The cleaning is now completed. Please refill with fog fluids.

5. Run the machine to make sure it can produce fog properly.

Note: All fog machines are prone to clogging due to the thick consistency of fog fluid and the

high temperature at which it vaporizes. However, a properly maintained fog machine should

provide years of reliable use.

Clean with a dry cloth only.

Store dry.

Performance Notes

. All fog machines develop condensation around the output nozzle. Because this may result

in some moisture accumulation on the surface below the output nozzle, consider this

condensation when installing your unit.

. All fog machines may sputter small amounts of fog occasionally during operation and for a

minute or so after being turned off.

. All fog machines have a recycling period after long bursts when the machine will shut itself

down for a short period in order to heat back up. During this time no fog can be produced.

The green “READY” L.E.D. on the remote will be off during this time and will light up again

when the machine is ready.

Save these instructions

DMX Connector Pin Assignment

The machine provide 3 pin XLR connector for DMX connection. Diagram below indicate pin

assignment information

Function

Ground

Data-

Data+

DMX Settings for Antari ICE Low Fog Machines with onboard DMX

6 –249 = Volume Control ( 5% - 95%)

250 –255 = Maximum Volume Output ( 100%)

The ICE Low Fog Machine has onboard DMX control. Currently this model uses 1

channel to

control Volume output operation. Each channel has a value range of 0 to 255.

If Channel A has a value from 0 to 5, the unit is OFF.

Between the values 6 to 249 the volume of fog output is regulated. With 6 being the

inimum volume of fog produced and 249 approaching the maximum. The volume output

rises as the DMX value is increased.

If Channel A has a value from 250 to 255, the machine will operate at maximum

output.

Note: In the example above, if the machine were assigned the DMX address of 124,

Channel A would correspond to DMX address 124.

In general, Antari fog machines with onboard DMX conform to the following performance

specifications:

1. Average Operating temperature = 250oC

2. Fogger can maintain maximum output for 30 seconds or more

3. Fogger can maintain constant output at 30% volume setting

(roughly a value of 70 –75).

Antari Onboard DMX Fog Machine Settings

Off

Be careful when open and close the cover!

Tabla de contenidos

Otros manuales de Máquina de niebla de Antari

Antari

Antari Z-300II Fazer Manual de usuario

Antari

Antari W-715 Manual de usuario

Antari

Antari II Series Manual de usuario

Antari

Antari M-1 Manual de usuario

Antari

Antari CINEMA HAZE CH-1 Manual de usuario

Antari

Antari Fogger X-510II Manual de usuario

Antari

Antari F-5D Fazer Manual de usuario

Antari

Antari FT-100 Fire Training Manual de usuario

Antari

Antari FT-55 Manual de usuario

Antari

Antari ICE-100 Manual de usuario

Antari

Antari Z-800 III Manual de usuario

Antari

Antari B-100X Manual de usuario

Antari

Antari HZ-350 Manual de usuario

Antari

Antari F-1 Fazer Manual de usuario

Antari

Antari M-4 Manual de usuario

Antari

Antari S-120 Manual de usuario

Antari

Antari F-6 Manual de usuario

Antari

Antari B-200 Manual de usuario

Antari

Antari X FAZER Manual de usuario

Antari

Antari F-4D Fazer Manual de usuario

Antari

Antari HZ-500 Manual de usuario

Antari

Antari F-4 Fazer Manual de usuario

Antari

Antari Onboard DMX Manual de usuario

Antari

Antari HZ-350 Manual de usuario

Manuales populares de Máquina de niebla de otras marcas

Boost

Boost BOOST-FOG400LED-BK Manual de usuario

Home Accents Holiday

Home Accents Holiday FM1000-ASH Manual de usuario

EuroLite

EuroLite ZEITGEIST FOG-1200 Manual de usuario

Dyna-Fog

Dyna-Fog CYCLONE ULTRA 2734 Manual de usuario

PROEL

PROEL DRAGO HEAVY PLFD150HY Manual de usuario

Sparklyn

Sparklyn Y846 Manual de usuario

Magicfx

Magicfx CO2 Gun Manual de usuario

Ibiza

Ibiza LSM500LAS Manual de usuario

Venue Lighting Effects

Venue Lighting Effects ULTRA MINI-FOGGER Manual de usuario

High End

High End F-100 Manual de usuario

Chauvet

Chauvet ARENA 2100 FLEX Manual de usuario

Beamz

Beamz F1600 Manual de usuario

Sagitter

Sagitter SG ARS900C Manual de usuario

KISANKRAFT

KISANKRAFT KK-STF-480 Manual de usuario

Orion

Orion OT-U250PP Guía

Beamz

Beamz S2500 Manual de usuario

American DJ

American DJ Dyno-Fog II Manual de usuario

JB Systems

JB Systems FX 1700 Manual de usuario