Antari DNG-250 Manual de usuario
1
DNG-250 Low Fog Generator
-User Manual
-
中文說明書
English - 中文
© 2019 Antari Lighting and Effects Ltd.
3
Thank you for choosing Antari’s DNG-250 Low Fog Generator. The machine has some
terrific new features on top of the ones of its previous version DNG-200. With the 3.5
TFT color touch panel, users can operate more easily. The dimension is exactly the same
as DNG-200, but the output volume and continuity are comprehensively increased,
hence a total up-grate in performance. No CO2is needed for DNG-250 Low Fog
Generator; therefore, there’s no risk to human body nor environment. DNG-250 is a real
green effect machine.
Please follow these operation, safety and maintenance instructions to ensure a longer
and safe life of your DNG-250 Low Fog Generator.
Pay attention to all warning labels and instructions printed on the exterior of the machine.
Safety Instructions
Keep this device dry.
For indoor use only. Not designed for outdoor use.
The ideal operating temperature is between 5° and 40° Celsius.
Two sets of professional power cords are used by this machine. It is important to
confirm the electrical voltage before plugging the power cord into the power outlet.
Use a three plug grounded power outlet.
If the machine is moved or transported, it shall be stationed for one hour to allow the
coolant in the cooler to stabilize before using it again.
If the machine is moved horizontally, please station it for 5 minutes before starting
the operation again.
Please unplug the power cord or turn off the machine when it is not in use.
This machine is not water-proof. If moisture, water, or fog fluid gets inside the
housing, immediately unplug the unit and clean it. If the machine cannot be cleaned,
please contact a service technician or your Antari dealer before using it again.
No user serviceable parts inside. Refer to your Antari dealer or other qualified service
personnel. For adult use only. The fog machine must be installed out of the reach of
4
children. Never leave the unit running unattended.
Operate the machine in a well-ventilated area. Never cover the unit's vents. The fog
machine is best installed 1 meter away from all objects.
It is important to place the machine on a flat surface instead of a surface with slope
to prevent any moving of the machine.
Do not add any inflammable liquid in the machine.
Make sure there is no any inflammable materials around the machine while operating.
If your Antari DNG-250 Low Fog Generator fails to work properly, please turn off the
power for five minutes and turn it on again. If the problem still exists, contact your
Antari dealer for service.
Always allow the machine to cool down before attempting to clean or service it.
Please use Antari FLL Low Fog Effects Fluid only. Please do not fill in any other fluid
into the tank to ensure the quality of the fog and the life of the machine.
If any malfunction happens, please unplug the machine and stop the operation.
Contact your Antari dealer for service.
Please make sure the tank if emptied before transportation.
Fog fluid is not edible, and ingestion by mistake might jeopardize your health. Please
do keep the fog fluids in safe place indoors. Seek for doctor’s help if ingest accidently.
Unpacking and Inspection
Open the shipping carton and verify that all equipment necessary to operate the system
has arrived intact. If any shortage or damage due to transportation, please contact your
Antari dealer and send back with original packaging for inspection. The shipping carton
should contain the following items:
.
-DNG-250 Low Fog Generator
-Two power cords for connecting to Neutrik PowerCon connectors.
-3M fog conducting hose
-User's manual (item 2-4 placed in the compartment on the top of the machine)
-Water collection tray (preinstalled in the machine)
-3M PU tube, 6mmØ
Setup
The wheels at the bottom of the DNG-250 help to move the machine; wheel fixing
mechanisms are located at the diagonal line. Position the machine at a spot, press
down the fixing mechanism to prevent it from moving. To move the machine, press
the opposite side of the fixing mechanism to release it. Please note that the machine
5
is not allowed to place on a slope due to its big size. (refer to figure 1)
Please aim the key on the PowerCon terminal of the power cord to the slot of the
connector on the machine, plug it in and turn it about 10° clockwise until the power
cord is completely fixed. The upper power cord is for the fog generator and the bottom
one is for the compressor. (refer to figure 2 and 3)
Before connecting the machine to power supply, make sure to check the needed
voltage and watt indicated on the metal plate of the machine.
Connect the machine with the black fog conducting hose; it is a three-meter pipe. The
length of the pipe can be adjusted to fit the actual need. (refer to figure 4)
Fill Antari FLL Low Fog Effects Fluid to the tank, tighten the tank cap. (refer to figure
5)
Figure 1
Figure 2
F
igure 3
6
Figure4 Figure5
Operation
1. After confirming the voltage, connect the power cord to a grounded outlet then turn
on the lower power switch and then the higher one. The warmup starts now, and the
TFT touch panel will show the percentage of the whole warmup process until 100%
that the warmup is completed.
2. TFT touch panel introduction：
2-1 Main Menu：
Manual mode
Heater status
DMX
Enforceable fluid drawing Main menu
Heater on/off
Timer mode
Preset 1 Preset 2
7
2-2 Manual mode：
2-2-1 Manual mode setting：
Continuous mode ON / OFF
Output volume 20% - 100%
2-3 Timer mode：
2-3-1 Timer mode setting:
Interval 5 secs – 200 secs
Duration 5 secs – 200 secs
Current setting of output volume
Current setting of fan speed
Manual mode setting
Start / Stop
Return
Return
Start / Stop
Current setting of
fan speed
Current setting of output
volume
Current setting of
interval time
Current setting of duration time
Timer mode setting
Return
Return
Current setting of fan speed
8
Continuous mode ON / OFF
Output volume 20% - 100%
2-4 DMX：
2-4-1 DMX setting：
DMX address setting
Return
DMX address:
DMX status
DMX setting
Heater temperature status
ConfirmCancel
Current address
9
2-5 Enforceable fluid drawing:
When the tank is refilled with fog fluid, use this to draw the fluid. Press
“Pause” once the output is back to avoid damp in fog. Default duration of the
fluid drawing is 1 min.
2-6 Heater：Heater can be activated or deactivated manually. Default setting is
activated.
Countdown
Pause
Start Return
Activate
Return
Deactivate
Heater activated Heater deactivated
Return
Return
10
2-7 Main menu：
2-7-1 DMX setting
DMX address setting. Please refer to page 8 for detail.
2-7-2 Basic information
Software version
Current working voltage (settable)
Usage time (from power on)
2-7-3 Setting
LCD brightness (Low/Medium/High/Auto)
*LCD light will shut down in 1 min when “Auto” is selected.
Action before shut down will be automatically proceeded after
warming up is finished.
Restore default setting.
Chinese/English
Software update (for Antari’s distributors’ use only)
Otros manuales para DNG-250
1
Tabla de contenidos
Otros manuales de Máquina de niebla de Antari
Antari
Antari M-1 Manual de usuario
Antari
Antari Z-3000II Manual de usuario
Antari
Antari FT-100 Fire Training Manual de usuario
Antari
Antari AF-5X Manual de usuario
Antari
Antari Z-Stream Manual de usuario
Antari
Antari FT-20 Manual de usuario
Antari
Antari HZ-350 Manual de usuario
Antari
Antari MOBILE MB-1 Manual de usuario
Antari
Antari M-8 Manual de usuario
Antari
Antari F-80Z Manual de usuario
Antari
Antari DNG250FE Manual de usuario
Antari
Antari Z Series Manual de usuario
Antari
Antari Z-80 Manual de usuario
Antari
Antari Z-300II Fazer Manual de usuario
Antari
Antari M-11 Manual de usuario
Antari
Antari M-7X Manual de usuario
Antari
Antari MOBILE MB-55 Manual de usuario
Antari
Antari ICE Manual de usuario
Antari
Antari W-715 Fog Jet Manual de usuario
Antari
Antari S-100 II Manual de usuario
Manuales populares de Máquina de niebla de otras marcas
Boost
Boost BOOST-FOG400LED-BK Manual de usuario
Home Accents Holiday
Home Accents Holiday FM1000-ASH Manual de usuario
EuroLite
EuroLite ZEITGEIST FOG-1200 Manual de usuario
Dyna-Fog
Dyna-Fog CYCLONE ULTRA 2734 Manual de usuario
PROEL
PROEL DRAGO HEAVY PLFD150HY Manual de usuario
Sparklyn
Sparklyn Y846 Manual de usuario
