Anet E10 Manual de usuario
Shenzhen Anet Technology
Co,.
Ltd.
3
D
Print Quality
Troubleshooting Guide
Print Quality Troubleshooting Guide .......................................................................... 1
Overview ..................................................................................................................... 1
1. Not Extruding at Start of Print............................................................................ 4
1.1 Filament was not loaded into extruder before printing ............................ 4
1.2 The distance between nozzle and bed is too close ................................... 5
1.3 The filament stripped against the drive gear............................................. 5
1.4 The extruder is clogged.............................................................................. 6
2. Print Not Sticking to the Bed.............................................................................. 7
2.1 Build platform is not level.......................................................................... 8
2.2 Nizzle starts too far away from the bed..................................................... 8
2.3 First layer is printing too fast ..................................................................... 9
2.4 Temperature or cooling settings ................................................................ 9
2.5 The build platform (tape, glues and materials) ....................................... 11
2.6 When all else fails: Brims and Rafts......................................................... 11
3. Not Extruding Enough Plastic........................................................................... 13
3.1 Incorrect filament diameter..................................................................... 13
3.2 Increase the extrusion speed................................................................... 14
4. Extruding Too Much Plastic .............................................................................. 15
5. Holes and Gaps in the Top Layers..................................................................... 17
5.1 Not enough top solid layers ..................................................................... 18
5.2 Infill percentage is too low....................................................................... 19
5.3 Under-extrusion....................................................................................... 19
6. Stringing or Oozing........................................................................................... 20
6.1 Retraction distance .................................................................................. 21
6.2 Retraction speed...................................................................................... 22
6.3 Temperature is too high........................................................................... 22
7. Overheating...................................................................................................... 24
7.1 Insufficient cooling................................................................................... 24
7.2 Print at too high temperature.................................................................. 25
7.3 Printing too fast........................................................................................ 25
7.4 When all above fall, try to print multiple parts at once .......................... 26
8. Layer Shifting or Misalignment ........................................................................ 27
8.1 Nozzle moves too fast.............................................................................. 28
8.2 Mechanical or Electrical issues ................................................................ 29
9. Layer Separation and Splitting.......................................................................... 31
9.1 Layer height is too large........................................................................... 32
9.2 Print temperature is too low.................................................................... 33
10. Grinding Filament............................................................................................. 34
10.1 Increase the extruder temperature ....................................................... 35
10.2 Print too fast .......................................................................................... 35
10.3 Check for a nozzle clog........................................................................... 36
11. Clogged Extruder.............................................................................................. 37
11.1 Manually push the filament to extruder................................................ 38
11.2 Reload the filament ............................................................................... 38
11.3 Clean out the nozzle .............................................................................. 39
12. Stops Extruding in the Middle of a Print .......................................................... 40
12.1 Out of filament....................................................................................... 41
12.2 The filament has stripped against the drive gear .................................. 41
12.3 The extruder is clogged.......................................................................... 41
12.4 Overheated extruder motor driver........................................................ 42
13. Weak Infill......................................................................................................... 43
13.1 Increase infill density ............................................................................. 44
13.2 Lower print speed.................................................................................. 44
14. Curling or Rough Corners ................................................................................. 45
15. Scars on Top Surface......................................................................................... 47
15.1 Extruding too much plastic .................................................................... 47
16. Holes and Gaps in Floor Corners ...................................................................... 48
16.1 Not enough perimeters.......................................................................... 49
16.2 Not enough top solid layers ................................................................... 49
16.3 Infill density is too low........................................................................... 50
17. Lines on the Side of Print ................................................................................. 51
17.1 Inconsistent extrusion............................................................................ 52
17.2 Temperature variation ........................................................................... 52
17.3 Mechanical issues .................................................................................. 53
18. Vibrations and Ringing ..................................................................................... 54
18.1 Print too fast .......................................................................................... 55
18.2 Firmware acceleration ........................................................................... 55
18.3 Mechanical issues .................................................................................. 56
19. Very Small Features Not Being Printed ............................................................ 57
19.1 Redesign the parts with thicker features............................................... 58
19.2 Install a nozzle with a smaller tip size.................................................... 58
19.3 Force the software to print small features ............................................ 59
20. Inconsistent Extrusion ...................................................................................... 60
20.1 Filament is getting stuck or tangled....................................................... 61
20.2 Clogged extruder ................................................................................... 61
20.3 Layer height is very low ......................................................................... 62
20.4 Poor quality filament ............................................................................. 62
20.5 Mechanical issues of extruder ............................................................... 63
1
Print Quality Troubleshooting Guide
Overview
Use the thumbnails below to identify the print quality issue that you are
seeing in your own 3D printed parts. You can click on the words under the
thumbnail to jump that portion of the guide for immediate recommendations on
how to resolve the issue. If you are not able to locate your issues from the
thumbnails, scroll down and read through each section of the guide for more
detail.
Not Extruding at Start of Print
Print Not Sticking to the Bed
Not Extruding Enough Plastic
2
Extruding Too Much Plastic
Holes and Gaps in the Top
Layers
Stringing or Oozing
Overheating
Layer shifting or Misalignment
Layer Separation and Splitting
Grinding Filament
Clogged Extruder
Stops Extruding Mid Print
3
Weak Infill
Curling or Rough Corners
Scars on Top Surface
Gaps in Floor Corners
Lines on the Side of Print
Vibrations and Ringing
Very Small Features Not Being
Printed
Inconsistent Extrusion
4
1. Not Extruding at Start of Print
This issue is very common for new 3D printer owners, but thankfully, it is also
very easy to resolve. There are four possible causes if your extruder does not
extrude plastic at the beginning of your print. We will walk through each one
below and explain how to solve the problem.
1.1 Filament was not loaded into extruder before printing
Most extruders have a problem of leaking plastic when they keep still at a
high temperature. The hot plastic inside the nozzle tends to ooze out of the tip,
which creates a void inside the nozzle where the plastic has drained out. This
idle oozing can occur at the beginning of a print when you are first preheating
your extruder, and also at the end of the print while the extruder is slowly cooling.
If your extruder has lost some plastic due to oozing, the next time you try to
extrude, it will take a few seconds before plastic starts to come out of the nozzle
again. If you are trying to start a print after you nozzle has been oozing, you may
notice the same delayed extrusion.
To solve this issue, make sure that you prime your extruder right before
beginning a print so that the nozzle is full of plastic and ready to extrude. A
common way to do this in Cura is by including something called a skirt. The skirt
will draw a circle around your part, and in the process, it will prime the extruder
with plastic.
5
If you need extra priming, you can increase the number of skirt outlines on
the Expert tab in Cura. You can also use control knob in Anet3D printer to extrude
plastic before printing.
1.2 The distance between nozzle and bed is too close
If the nozzle is too close to the bed, there will not be enough room for plastic
to come out of the extruder. The hole in the top of the nozzle is essentially blocked
so that no plastic can come out. An easy way to recognize this issue is if the print
does not extrude plastic for the first layer or two, but begins to extrude normally
around the 3rd or 4th layers. To solve this problem, you can adjust the four screws
at the corners of the hot bed, turn the screws clockwise and the hot bed will move
down. Turn a little once to increase the distance until there is enough space for
plastic extrusion (The distance is about the thickness of a piece of A4 Paper ).
1.3 The filament stripped against the drive gear
Anet3D printers use a small gear to push the filament back and forth. The teeth
on this gear bite into the filament and allow it to accurately control the position of the
filament. However, if you notice lots of plastic shavings or it looks like there is a
section missing from your filament, then it’s possible that the drive gear has removed
too much plastic. Once this happens, the drive gear won’t have anything left to grab
onto when it tries to move the filament back and forth. Please see the Grinding
Filament section for instructions on how to fix this issue.
Otros manuales para E10
1
Tabla de contenidos
Otros manuales de Impresora 3D de Anet
Anet
Anet A8 Plus Manual de usuario
Anet
Anet A8 Manual de usuario
Anet
Anet E10 Manual de usuario
Anet
Anet A8 Plus Manual de usuario
Anet
Anet A6 Manual de usuario
Anet
Anet A6 Manual de usuario
Anet
Anet A2 Manual de usuario
Anet
Anet A8 Manual de instrucciones
Anet
Anet ET4 Pro Manual de usuario
Anet
Anet ET5 X Guía del usuario
