AMX CTC-1402 Manual de usuario

USER MANUAL

VERSION: V1.0.0

CTC-1402

Connectivity and Transport Kit - Conferencing

AV FOR AN IT WORLD®

IMPORTANT SAFETY INSTRUCTIONS

1. READ these instructions.

2. KEEP these instructions.

3. HEED all warnings.

4. FOLLOW all instructions.

5. DO NOT use this apparatus near water.

6. CLEAN ONLY with dry cloth.

7. DO NOT block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. DO NOT install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampliers) that

produce heat.

9. DO NOT defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades with one wider than the

other. A grounding type plug has two blades and a third grounding prong. The wider blade or the third prong are provided for your

safety. If the provided plug does not t into your outlet, consult an electrician for replacement of the obsolete outlet.

10. PROTECT the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where

they exit from the apparatus.

11. ONLY USE attachments/accessories specied by the manufacturer.

12. USE ONLY with a cart, stand, tripod, bracket, or table specied by the manufacturer, or sold with the apparatus. When a cart is

used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. UNPLUG this apparatus during lightning storms or when unused for long periods of time.

14. REFER all servicing to qualied service personnel. Servicing is required when the apparatus has been damaged in any way, such as

power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate normally, or has been dropped.

15. DO NOT expose this apparatus to dripping or splashing and ensure that no objects lled with liquids, such as vases, are placed on

the apparatus.

16. To completely disconnect this apparatus from the AC Mains, disconnect the power supply cord plug from the AC receptacle.

17. Where the mains plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily

operable.

18. DO NOT overload wall outlets or extension cords beyond their rated capacity as this can cause electric shock or re.

The exclamation point, within an equilateral triangle, is intended to alert the user to the presence of important operating and

maintenance (servicing) instructions in the literature accompanying the product.

The lightning ash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated

“dangerous voltage” within the product’s enclosure that may be of sucient magnitude to constitute a risk of electrical shock to

persons.

ESD Warning: The icon to the left indicates text regarding potential danger associated with the discharge of static electricity from an

outside source (such as human hands) into an integrated circuit, often resulting in damage to the circuit.

WARNING: To reduce the risk of re or electrical shock, do not expose this apparatus to rain or moisture.

WARNING: No naked ame sources - such as candles - should be placed on the product.

WARNING: Equipment shall be connected to a MAINS socket outlet with a protective earthing connection.

WARNING: To reduce the risk of electric shock, grounding of the center pin of this plug must be maintained.

means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of AMX. Copyright protection claimed

extends to AMX hardware and software and includes all forms and matters copyrightable material and information now allowed by statutory or judicial

law or herein after granted, including without limitation, material generated from the software programs which are displayed on the screen such as

icons, screen display looks, etc. Reproduction or disassembly of embodied computer programs or algorithms is expressly prohibited.

LIABILITY NOTICE

No patent liability is assumed with respect to the use of information contained herein. While every precaution has been taken in the preparation of

this publication, AMX assumes no responsibility for error or omissions. No liability is assumed for damages resulting from the use of the information

contained herein. Further, this publication and features described herein are subject to change without notice.

AMX WARRANTY AND RETURN POLICY

The AMX Warranty and Return Policy and related documents can be viewed/downloaded at www.amx.com.

User Manual - CTC-1402 3

To avoid ESD (Electrostatic Discharge) damage to sensitive components, make sure you are properly grounded before

touching any internal materials.

When working with any equipment manufactured with electronic devices, proper ESD grounding procedures must be

followed to make sure people, products, and tools are as free of static charges as possible. Grounding straps, conductive

smocks, and conductive work mats are specically designed for this purpose. These items should not be manufactured

locally, since they are generally composed of highly resistive conductive materials to safely drain static discharges, with-

out increasing an electrocution risk in the event of an accident.

Anyone performing eld maintenance on AMX equipment should use an appropriate ESD eld service kit complete with at

least a dissipative work mat with a ground cord and a UL listed adjustable wrist strap with another ground cord.

WARNING: Do Not Open! Risk of Electrical Shock. Voltages in this equipment

are hazardous to life. No user-serviceable parts inside. Refer all servicing to

qualied service personnel.

Place the equipment near a main power supply outlet and make sure that you

can easily access the power breaker switch.

ESD WARNING

WARNING: This product is intended to be operated ONLY from the voltages listed on the back panel or the recommended,

or included, power supply of the product. Operation from other voltages other than those indicated may cause irre-

versible damage to the product and void the products warranty. The use of AC Plug Adapters is cautioned because it

can allow the product to be plugged into voltages in which the product was not designed to operate. If the product is

equipped with a detachable power cord, use only the type provided with your product or by your local distributor and/or

retailer. If you are unsure of the correct operational voltage, please contact your local distributor and/or retailer.

FCC AND CANADA EMC COMPLIANCE INFORMATION:

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to

part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a

commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment o and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Approved under the verication provision of FCC Part 15 as a Class A Digital Device.

Caution

Changes or modications not expressly approved by the manufacturer could void the user’s authority to operate this device.

CAN ICES-3 (B)/NMB-3(B)

EU COMPLIANCE INFORMATION:

Eligible to bear the CE mark; Conforms to European Union Low Voltage Directive 2006/95/EC; European Union EMC Directive

2004/108/EC; European Union Restriction of Hazardous Substances Recast (RoHS2) Directive 2011/65/EU; European Union

WEEE (recast) Directive 2012/19/EU; European Union Radio and Telecommunications Terminal Equipment (R&TTE) Directive

1999/5/EC

WEEE NOTICE:

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

This appliance is labeled in accordance with European Directive 2012/19/EU concerning waste of electrical and

electronic equipment (WEEE). This label indicates that this product should not be disposed of with household

waste. It should be deposited at an appropriate facility to enable recovery and recycling.

User Manual - CTC-1402 4

Table of Contents

Important Safety Instructions ............................................................................................2

Overview .......................................................................................................................6

Features .......................................................................................................................6

Package Contents .......................................................................................................6

Specications...............................................................................................................7

Transmitter Front Panel Description ........................................................................ 10

Transmitter Rear Panel Description.......................................................................... 12

Receiver Front Panel Description ............................................................................. 13

Receiver Rear Panel Description .............................................................................. 14

Pinout Information ........................................................................................................... 15

RS232 ....................................................................................................................... 15

RELAY ........................................................................................................................ 15

Audio Out .................................................................................................................. 16

Installation........................................................................................................................ 17

Wiring ........................................................................................................................ 18

OSD ............................................................................................................................ 19

Input Source Switching.................................................................................................... 20

Auto Switching .......................................................................................................... 20

Manual Switching...................................................................................................... 20

USB Control ...................................................................................................................... 21

NetLinx Studio Control ..................................................................................................... 24

Device Number and Ports ......................................................................................... 24

Send Commands to Control a Device........................................................................26

Telnet Control via NetLinx Studio ..............................................................................26

Web UI Control...........................................................................................................28

Web UI Control ..................................................................................................................29

Access the Web Interface ..........................................................................................29

Web Interface Introduction ...................................................................................... 30

Refresh....................................................................................................................... 30

Factory Default .......................................................................................................... 30

Reboot ....................................................................................................................... 30

Upgrade Status ......................................................................................................... 31

LOGOUT ..................................................................................................................... 31

Firmware VERSION.................................................................................................... 31

Auto Switch: .............................................................................................................. 31

Key Lock .................................................................................................................... 31

User Manual - CTC-1402 5

HDCP.......................................................................................................................... 31

EDID ...........................................................................................................................32

Display ........................................................................................................................32

RS232 Setting ............................................................................................................32

Relay ...........................................................................................................................33

Audio Volume ............................................................................................................ 34

Resolution.................................................................................................................. 34

Network ......................................................................................................................35

System ........................................................................................................................36

ICSP Parameter..........................................................................................................36

Login Password ..........................................................................................................36

TELNET/SSH Access ................................................................................................. 37

TELNET Account........................................................................................................ 37

SSH Account.............................................................................................................. 37

Firmware Upgrade .............................................................................................................38

Before Starting...........................................................................................................38

Transferring KIT Files.................................................................................................38

Troubleshooting................................................................................................................ 40

API Command Set ............................................................................................................ 41

NetLinx Commands ................................................................................................... 42

Telnet/SSH Commands............................................................................................. 50

User Manual - CTC-1402 6

Overview

The CTC-1402 is a 4K 6x Multi-format Inputs Extender Switch with USB extension and includes a scaler for CTC-1402 The

transmitter and receiver kit oers six video inputs shared between both devices for HDMI, Display Port, VGA plus analog audio

in and USB-C video signals. To simplify conference room device management, the kit provides four USB type B connectors for

host Computers. Six built-in USB hubs, three on the transmitter and three on the receiver, allow for the use of numerous Human

Interface Devices (HID) as well as USB cameras and microphones.

The kit is compatible with sources up to 4K / 60Hz with 4:4:4 color subsampling. All audio, video, data, control, USB, and Ethernet

transmission between the two devices is carried over a single, Ethernet-enabled HDBaseT link up to 328 feet (100 meters).

The CTC-1402 simplies classroom and small oce system integration, for installation beneath conference tables and in lecterns,

to provide localized presentation switching support.

Features

• Built-in scaler and DSC

• Supports up to 4K@60Hz 4:4:4 8bit HDMI In/Out

• Supports HDMI 2.0 and HDCP 2.2

• Provides a variety of interfaces, including USB-C, to simplify meeting room devices management

• Supports USB hosts like Desktop and Laptop, USB devices like keyboard/MIC/Speaker/Camera/Whiteboard for conference

systems

• Automatically detects active inputs when sources are connected or there is a source signal change

• Ethernet can be imported from either receiver or transmitter, providing LAN accessibility for users

• The source device with USB-B or connected with USB-C will be controlled by the USB device via video auto-detection

technology

• Control or upgrade via Harman NetLinx studio, Control of 3rd party devices via serial port of the CTC-1402

• Allows control of connected displays On/O via CEC by using NetLinx studio or front panel buttons

• Allows control relay such as the raising and lowering of project screens

• RS232 bi-directional pass through

• IR pass through from TX to RX

• De-embedded Audio Out/In Receiver

• Supports fast switch

Package Contents

• 1 x CTC – 1402 Transmitter

• 1 x CTC – 1402 Receiver

• 2 x DC 12V Power Adapter (with US, UK, EU Power Cords)

• 1 x Broadband IR Receiver (30KHz-50KHz)

• 1 x IR Emitter

• 8 x Phoenix Male Connector (3.5mm, 3 Pins)

• 1 x Phoenix Male Connector (3.5mm, 2 Pins)

• 4 x Mounting Bracket (with Screws)

User Manual - CTC-1402 7

Specications

Technical

Input 1 x HDMI IN

1 x DisplayPort IN

1 x USB-C IN

1 x VGA IN

1 x Audio IN (followed with VGA IN)

Input Signal Type HDMI with 4K@60Hz 4:4:4 8bit, HDCP 2.2;

DP/USB-C : DP 1.2a

Input Resolution

Supported

HDMI Input Resolution supported:

VESA:

800x6008, 1024x7688, 1280x7688,

1280x8008, 1280x9608, 1280x10248,

1360x7688, 1366x7688, 1440x9008,

1600x9008, 1600x12008, 1680x10508

1920x10808,

SMPTE:

1920x12008,2560x14408,2560x16008

3840x2160P2,3,5,6,8(YUV4:2:0) ,

4096x21602,3,5,6,8 (YUV 4:2:0)

1 = at 23.98 Hz, 2 = at 24 Hz, 3 = at 25 Hz, 4 = at 29.97 Hz, 5 = at 30 Hz, 6 = at 50 Hz, 7 = at 59.94

Hz, 8 = at 60 Hz

Established Timing including interlaced formats:

1280 x 1024 @ 75 Hz

1152 x 870 @ 75 Hz

1024 x 768 @ 60 Hz, 70 Hz, 75 Hz, 87 Hz

832 x 624 @ 75 Hz

800 x 600 @ 56 Hz, 60 Hz, 72 Hz, 75 Hz

720 x 400 @ 70 Hz, 88 Hz

640 x 480 @ 60 Hz, 67 Hz, 72 Hz, 75 Hz

CEA Video Information Code (VIC) Formats:

VIC = 1, 640 x 480p 59.94/60 Hz 4:3

VIC = 2, 720 x 480p 59.94/60 Hz 4:3

VIC = 3, 720 x 480p 59.94/60 Hz 16:9

VIC = 4, 1280 x 720p 59.94/60 Hz 16:9

VIC = 5, 1920 x 1080i 59.94/60 Hz 16:9

VIC = 6, 720(1440) x 480i 59.94/60 Hz 4:3

VIC = 7, 720(1440) x 480i 59.94/60 Hz 16:9

VIC = 14, 1440 x 480p 59.94/60 Hz 4:3

VIC = 15, 1440 x 480p 59.94/60 Hz 16:9

VIC = 16, Native 1920 x 1080p 59.94/60 Hz 16:9

VIC = 17, 720 x 576p 50 Hz 4:3

VIC = 18, 720 x 576p 50 Hz 16:9

VIC = 19, 1280 x 720p 50 Hz 16:9

VIC = 20, 1920 x 1080i 50 Hz 16:9

VIC = 21, 720(1440) x 576i 50 Hz 4:3

VIC = 22, 720(1440) x 576i 50 Hz 16:9

VIC = 29, 1440 x 576p 50 Hz 4:3

VIC = 30, 1440 x 576p 50 Hz 16:9

VIC = 31, 1920 x 1080p 50 Hz 16:9

VIC = 32, 1920 x 1080p 23.97/24 Hz 16:9

VIC = 33, 1920 x 1080p 25 Hz 16:9

VIC = 34, 1920 x 1080p 29.97/30 Hz 16:9

VIC = 39, 1920 x 1080i 50 Hz 16:9

VIC = 41, 1280 x 720p 100 Hz 16:9

VIC = 42, 720 x 576p 100 Hz 4:3

VIC = 43, 720 x 576p 100 Hz 16:9

VIC = 44, 720(1440) x 576i 100 Hz 4:3

VIC = 45, 720(1440) x 576i 100 Hz 16:9

VIC = 47, 1280 x 720p 119.88/120 Hz 16:9

VIC = 48, 720 x 480p 119.88/120 Hz 4:3

VIC = 49, 720 x 480p 119.88/120 Hz 16:9

VGA Input Resolution supported:

Up to 1920 x 1200 @ 60Hz

Input Video Level 0.5-1.0 V p-p

Maximum Pixel Clock 600 MHz

Output 1 x HDBT OUT

Transmitter

User Manual - CTC-1402 8

Output Signal Type HDMI with 4k@60Hz 4:4:4 8-bit

HDBT 2.0

Video Impedance 100 Ω

Audio Format

Support-ed

PCM 2.0

General

Operating

Temperature

0°C to 50°C (32°F to 125.6°F)

Storage Temperature -10°C to 60°C (14°F to 140°F)

Humidity 5% to 85%, non-condensing

ESD Protection Human-body Model:

±10kV(Air-gap discharge)/±5kV(Contact discharge)

Surge Protection Voltage: ±1 kV

Power Supply 12V, 3A

Power Consumption

(Max)

2K: 13.36W

4K: 17.38W (4K full loaded)

Device Dimension

(W x H x D)

220mm x 42mm x 160mm /8.66’’ x 1.65’’ x 6.30’’

Product Weight 0.97kg/2.14lb

Certication CE/FCC/ETL/PSE/RCM

Receiver

Technical

Input 1 x HDBT IN

2 x HDMI IN

Input Signal Type HDMI with 4k@60Hz with Chroma sub-sampling 4:4:4 8bit

HDBT 2.0

Resolution Support VESA:

800x6008, 1024x7688, 1280x7688,

1280x8008, 1280x9608, 1280x10248,

1360x7688, 1366x7688, 1400x10508

1440x9008, 1600x9008,1600x12008,

1680x10508, 1920x10808, 1920x12008,

SMPTE:

1280x7206,8,1920x1080P6,7,8, 3840x21602,3,5,6,8, 4096x21602,3,5,8

1 = at 23.98 Hz, 2 = at 24 Hz, 3 = at 25 Hz, 4 = at 29.97 Hz, 5 = at 30 Hz, 6 = at 50 Hz,

7 = at 59.94 Hz, 8 = 60 Hz;

Input Video Level 0.5-1.0 V p-p

Maximum Pixel Clock 600MHz

Output 1 x HDMI OUT

Output Signal Type HDMI

Video Impedance 100 Ω

Audio Format Sup-

ported

PCM 2.0

General

Operating

Temperature

0°C to 50°C (32°F to 125.6°F)

Storage Temperature -10°C to 60°C (14°F to 140°F)

Humidity 5% to 85%, non-condensing

Surge Protection Voltage: ±1 kV

User Manual - CTC-1402 9

Power Supply DC12V 3A

Power Consumption

(Maximum)

2K: 22.8W

4K: 25.36W

Device Dimension

(W x H x D)

220mm x 42mm x 160mm /8.66’’ x 1.65’’ x 6.30’’

Product Weight 0.95kg/2.09lb

ESD Protection Human-body Model:

±10kV(Air-gap

discharge)

0.97kg/2.14lb

±5kV(Contact

discharge)

CE/FCC/ETL/PSE/RCM

Certication CE/FCC/ETL/PSE/RCM

Transmission Distance:

Note: Straight-through category cables wired to T568B standard recommended.

Cable Type Range Supported Video

HDMI Input/Output:15m/50ft 1080p@60Hz, 24bpp

Input/ Output: 10m/33ft 4K@30Hz 4:4:4

Input/Output: 5m/16ft 4K@60Hz, 4:4:4

Shielded Cat 6a/7 100m/330ft 1080p@60Hz

80m/ 262 ft 4K@30Hz, 4:4:4

4K@60Hz, 4:2:0

4K@30Hz, 4:4:4

User Manual - CTC-1402 10

Transmitter Front Panel Description

No. Name Description

1 POWER LED

(Green)

On: The CTC-1402 TX is powered on.

O: The CTC-1402 TX is powered o.

2 Auto Auto Switch Button: Press to enable/disable auto switching function.

LED (Blue): LED is located on the top of the button.

• ON: Input auto switching function is enabled (default).

• O: Input auto switching function is disabled.

31 VGA 1 VGA Button: Press to select VGA as input.

LED: LED is located on the top of the button.

• Green: the input has signal and is selected.

• Yellow: the input has signal but is not selected.