AMG AMG4713E Manual de usuario

AMG Systems Ltd. reserves the right to make changes to this

document without notice. The information herein is believed to

be accurate. No responsibility is assumed by AMG for its use.

Page

AMG4713E

Instruction

Sheet

D16986

01.doc

AMG4713E

Instruction Manual

Single Channel Video Transmit Unit with Bi

directional Data

Channel plus Ethernet

The

AMG4713E

is a standalone single channel video transmit unit designed to transmit 1 video signal

and transmit and receive 1 data sig

nal plus full duplex 100BaseT Ethernet connectivity over two

singlemode fibres.

The

AMG4713E

is designed to be powered using an

AMG2003

standalone power supply.

The

AMG4713E

is designed to operate with

AMG4714E

or rackmount equivalent

AMG4714ER

one

chan

nel video receive unit in a point to point configuration.

AMG Systems Ltd. reserves the right to make changes to this

document without notice. The information herein is believed to

be accurate. No responsibility is assumed by AMG

for its use.

Page

AMG4713E

Instruction

Sheet

D16986

01.doc

Contents

Introduction

Optical Connection

................................

.............................

Unit Functional Schematic

................................

..................

Connections

Video Input Connections

................................

....................

Optical Connections

................................

...........................

Power Connection

................................

..............................

Ethernet Connection

................................

...........................

Data and Audio Cha

nnel Connections

................................

...............................

Data and Audio Channel Configuration

................................

..............................

Data Interface Connections Channel A

................................

..............................

Data Channel A Configuration

................................

............

Front Panel Indicators

Power LED

................................

..........

Video Input LED’s

................................

...............................

Fibre Optic LED’s

................................

...............................

Low Speed Data LEDs

................................

.......................

Ethernet Operation

Physical Information

Dimensions

................................

.........

Mounting Details

................................

Remova

l / replacement from / to the Case

................................

.........................

Safety

Maintenance and Repair

AMG Systems Ltd. reserves the right to make changes to this

document without notice. The in

formation herein is believed to

be accurate. No responsibility is assumed by AMG for its use.

Page

AMG4713E

Instruction

Sheet

D16986

01.doc

Introduction

Optical Connection

The

AMG4713E

is connected as illustrated below when used wi

th an

AMG4714E

receive unit acting

as a point to point system.

Unit Functional Schematic

The

AMG4713E

transmits one video and 1

data signal to the

AMG4714E

It also receives 1 data signal transmitted

from the

AMG4714E

Ethernet connectivity is also pro

vided

between the two units.

AMG Systems

Ltd. reserves the right to make changes to this

document without notice. The information herein is believed to

be accurate. No responsibility is assumed by AMG for its use.

Page

AMG4713E

Instruction

Sheet

D16986

01.doc

Connections

Video Input Connections

No. of channels

................................

....

Connector

................................

............

75 ohm BNC Socket.

Input Impedance

................................

75 ohm terminated.

Input Level

................................

...........

1 volt p

p nominal

Frequency Response

...........................

10Hz to 7MHz.

Optical Connections

PRIMARY OPTO O

Connector

................................

............

LC/PC

Primary Optical Launch Power

............

5dBm

Wavelength

................................

..........

1310nm

Optical Fibre

................................

........

Singlemode

PRIMARY OPTO IN

Connector

................................

............

LC/PC

Primary Optical Sensitivity

...................

22dBm

Wavelength

................................

..........

1310nm

Optical Fibre

................................

........

Singlemode

Power Connection

Connector Type

................................

...

2.1mm screw lo

ck long power jack

–

centre positive

Connector Partno.

................................

Switchcraft S761K, AMG G16125

Supply Voltage

................................

.....

13.5 to 18.0 Volts DC.

Maximum Power

................................

5 Watts

Ethernet Connection

Ethernet Data Connector

....................

RJ45

Interface

................................

...............

Auto

negotiation up to 100BASE

TX full dupl

Ethernet Data Rate

..............................

Maximum 50Mbits/s total Ethernet traffic on fibre

Data and Audio Channel Connections

DATA CHANNEL A

Data Channel A

................................

...

1 channel

Data Connector

................................

....

RJ45

Channel A Interface

.............................

On Board Data Interface

–

RS232, RS422 or RS485. Selected

by slide

switch above the RJ45 connector.

RS232

–

switch position

high (closest to BNC connections)

RS422

–

switch position

–

middle

RS485

–

switch position

–

low (furthest from BNC connections)

DATA CHANNEL B

Data Channel B

................................

...

Not Present

AMG Systems Ltd. reserves the right to make changes to this

document without notice. The information herein is believed to

be accurate. No responsibility is assumed by AMG for its use.

age

AMG4713E

Instruction

Sheet

D16986

01.doc

Data and Audio Ch

annel Configuration

Data and Audio Channel Configuration

The

AMG4713E

and rackmount equivalent

AMG4713ER

sends and receives data to/from Channel A.

Channel B is not available. Channel A is a single data interface selectable by the user with the slide

switc

h on the rear panel.

Data Interface Connections Channel A

Channel A

RJ45 Pin

No.

RS485

[switch low]

RS422 [switch

mid]

RS232

[switch high]

Cat 5/6 Cable

Colour Code T568B

IN + (A)

GND

White/orange

(B)

Orange

White/green

Blue

White/blue

Green

IN/OUT + (A)

OUT + (A)

N/A

White/brown

IN/OUT

(B)

OUT

(B)

OUT

Brown

Note: (A) or (B) in brackets in above table refers to RS485 / RS422 data specification, not Channel A,

Channel

Data Channel A Configuration

Channel A is always present and allows for a RS232, RS422 (full duplex, four wire) or RS485 (half

duplex, two wire) interface depending on the position of the switch located above the RJ45 connector.

The switch signifies t

he presence of the X16004 Low Speed Data/Audio Interface Board. If there are

LED's present on the RJ45 connector then an X16003 Ethernet Interface Board is fitted.

The data input for both the RS485 and the RS422 modes detects a tri

state input condition b

monitoring the differential voltage level across the input. A differential level below 600mV positive or

negative will be detected as a tri

state condition. A level above 600mV positive or negative will be

detected as a logic 1 or logic zero respectively

. It is important therefore to terminate the RS485 bus or

the RS422 input bus using 120Ωif a pre

bias is present on the RS485 or RS422 bus.

A large number of third party equipment manufacturers apply a pre

bias on their RS485 bus. This pre

bias is appli

ed by pulling one arm of the RS485 bus high (+5 volts) and the other arm low (0 volts)

using high value resistors within the third party equipment. In order to ensure that the AMG equipment

detects a tri

state condition, then these resistors should have a

value above 5kΩ. If the third party

bias resistors are less the 750Ωthe bus can be double or triple terminated as required to ensure that a

tri

state level is detected.

Note: The Data Channel A is shipped from the factory set up for RS485 operation unle

ss otherwise

requested.

AMG Systems Ltd. reserves the right to make changes to this

document without notice. The information herein

is believed to

be accurate. No responsibility is assumed by AMG for its use.

Page

AMG4713E

Instruction

She

D16986

01.doc

Front Panel Indicators

Power LED

Power

................................

...................

Green

unit powered

Off

no power applied to unit

Video Input LED’s

Video Present CH1

..............................

Green

video signal present on input BNC

Org

channel present but no video on I/P BNC

Fibre

Optic LED’s

Primary Opto Sync TX

.........................

Green

optical channel transmitting

Off

optical channel not transmitting

Primary Opto Sync RX

.........................

Green

optical channel receiving

Org

optical channel receiving but not sync.

Off

optical channel not transmittin

Low Speed Data LEDs

Channel A

Data Present TX (RS485 or RS422)

...

Green

logic zero (+V,

V) present on IN+, IN

Red

logic one (

V,V+) present on IN+, IN

Off

tri

state off or no connection on IN+, IN

Data Present TX (RS232)

....................

Green

logic zero (

+V) present on input IN+

Red

logic transitions present on input IN+

Off

logic one (

V) present on input IN+

This represents the data signals being transmitted on the optical fibre

Data Present RX (RS485 or RS422)

...

Green

logic zero (+V,

V) present

on OUT+, OUT

Red

logic one (

V,+V) present on OUT+, OUT

Off

tri

state off or no connection on OUT+, OUT

Data Present RX (RS232)

...................

Green

logic zero (+V) present on OUT+

Red

logic transitions present on OUT+

Off

logic one (

V) present on

OUT+

This represents the data signals being received on the optical fibre

AMG Systems Ltd. reserves the right to make changes to this

document without notice. The information herein is believed to

be accurate. No responsibility is assumed by AMG for its use.

Page

AMG4713E

Instruction

Sheet

D16986

01.doc

Ethernet Operation

In order for the AMG system to transmit Ethernet signals, an onboard RJ45 Ethernet interface or

X16003 Ethernet interface adaptor should be fitted to both the

Transmit unit and the Receive unit.

The Ethernet interface can operate at either 10Mbits/s half duplex, or 100Mbit/s full duplex, and data is

transmitted from one port the other port with the minimum of delay or buffering. The maximum

bandwidth (at 100Mb

it/s full duplex) available for transmission across the fibre link is nominally

50MBit/s.

The 100BaseT port does not implement MDI/MDIX; it should be connected with a straight though

cable to an external switch port and with a cross over cable when conne

cted directly to a PC or DTE.

AMG Systems Ltd. reserves the right to make changes to this

document without notice. The information herein is believed to

be accurate. No responsibility is assumed by AMG for

its use.

Page

AMG4713E

Instruction

Sheet

D16986

01.doc

Physical Information

Dimensions

Height

................................

...................

112mm

Width

................................

....................

170mm (excluding connectors)

Depth

................................

...................

70mm

Weight

................................

..................

750grams

Mounting Details

The AMG unit is supplied with a clip

on mounting bracket which should be attached to a panel or w

all

using 2 off 4.0mm screws, see diagram on page 1 for dimensions. The unit is clipped into the

mounting bracket, and is then held firmly in position.

Removal / replacement from / to the Case

Note:

The AMG unit PCB's are static sensitive. Handle with

proper care and use normal electrostatic

discharge (ESD) procedures. Use properly grounded protection (for example, wrist straps) when

handling the PCB.

To remove units from the case to access the data expansion boards and the daughter boards, remove

the

2 or 4 fixing screws on the rear panel and slide the PCB's out of the case.

Ensure that the fibres do not snag or get trapped.

To replace the PCB's into the case, slide the PCB's gently into the case aligning the boards with the

appropriate slots. Ensu

re that the fibre do not snag or get trapped.

Safety

AMG Optical Fibre Products use Class 1 laser systems in accordance with EN 60825

2:2000.

It is always advisable to follow good practice when working with optical fibre systems. This includes:



Do not

stare with unprotected eyes or with any unapproved collimating device at fibre

ends or connector faces, or point them at other people.



Use only approved filtered or attenuating viewing aids

For other safety issues and advice on good practice associated w

ith optical fibre systems, please see

EN 60825

2:2000 or your local safety officer.

Maintenance and Repair

There are no user serviceable parts within AMG products. See unit data sheet for full specification.

In case of problem or failure, please call y

our local support centre or contact:

AMG Systems Ltd.

3 The Omega Centre, Stratton Business Park, Biggleswade, Beds., SG18 8QB, UK.

Phone

+44 (0) 1767 600 777

Technical Support

+44 (0) 1767 604 491

techsupport@amgsystems.com

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Transmisor de AMG

AMG

AMG AMG4683B ER Series Manual de usuario

AMG

AMG AMG6781 Manual de usuario

AMG

AMG AMG5513A6B9 Manual de usuario

AMG

AMG AMG4781ER-SF Manual de usuario

AMG

AMG AMG4707AEG Manual de usuario

AMG

AMG AMG4747AG-SF Manual de usuario

AMG

AMG AMG4643-DR-SF Manual de usuario

AMG

AMG AMG4687BE Manual de usuario

AMG

AMG AMG5913-2A9R Manual de usuario

AMG

AMG AMG4681R-CWDMn Manual de usuario

AMG

AMG AMG4681-1550-C Manual de usuario

AMG

AMG AMG5611 Manual de usuario

AMG

AMG AMG4687BER Manual de usuario

AMG

AMG AMG4647B Manual de usuario

AMG

AMG AMG5713A6B9-HP Manual de usuario

AMG

AMG AMG4783B R-SF Series Manual de usuario

AMG

AMG AMG5513A5B9 Manual de usuario

AMG

AMG AMG4684B R Series Manual de usuario

AMG

AMG AMG5713A6B9-DIN Manual de usuario

AMG

AMG AMG4783RN-CWDMn Manual de usuario

AMG

AMG AMG4687BR Manual de usuario

AMG

AMG AMG4723 Manual de usuario

AMG

AMG AMG5613A9R Manual de usuario

AMG

AMG AMG4707G Manual de usuario

Manuales populares de Transmisor de otras marcas

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manual del propietario

Honeywell

Honeywell 5816WMBR Manual de usuario

Kamstrup

Kamstrup READy MTU Instrucciones de funcionamiento

Omega

Omega ZW Series Manual de usuario

ABB

ABB Field 264H Guía

Alinco

Alinco DJ-V17T Manual de usuario

Dejero

Dejero EnGo 3x Manual de usuario

Rosemount

Rosemount 4600 Manual de usuario

Speaka Professional

Speaka Professional 2342740 Manual de usuario

trubomat

trubomat GAB 1000 Manual de usuario

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manual de usuario

Rondish

Rondish UT-11 Manual de usuario

MG 10JRE Manual de usuario

Burkert

Burkert 8177 Manual de usuario

Firetide

Firetide HotPort 3203 Manual

Tele Radio

Tele Radio T9-02 Manual de usuario

Rotronic

Rotronic HygroFlex HF3 Series Manual de usuario

Jamara

Jamara FCX6 Pro Tel Manual de usuario