AMG AMG4783E-DR-SF Manual de usuario

AMG Systems Ltd. reserves the right to make chang

es to this

document without notice. The information herein is believed to

be accurate. No responsibility is assumed by AMG for its use.

Page

AMG4783E

Instruction

Sheet

D16828

02.doc

AMG4783E

Instruction Manual

8 Channel Video Transmit Unit with 1 Bi

directional Data

Channel plus Ethernet and Dual Redundant Operation

The

AMG4783E

is a standalone eight channel video transmit unit designed to transmit 8 video

signa

ls and transmit and receive 1 data signal plus full duplex 100BaseT Ethernet connectivity over

one singlemode fibre with Dual Redundant operation.

The

AMG4783E

is designed to be powered using an

AMG2003

standalone power supply.

The

AMG4783E

is designed to operate with

AMG4784E

or rackmount equivalent

AMG4784ER

eight channel video receive unit in a point to point configuration.

AMG Systems Ltd. reserves the right to make changes to this

document without notice. The information herein is believed to

be accurate. No responsibility is assumed by AMG for its use.

Page

AMG4783E

Instruction

Sheet

D16828

02.doc

Contents

Introduction

Unit Functional Schematic

................................

..................

Optical Connection

................................

.............................

Connections

Video Input Connections

................................

....................

Optical Connections

................................

...........................

Power Connection

................................

..............................

Ethernet Connection

................................

...........................

Data and Audio Channel Connections

................................

...............................

Data and Audio Channel Configuration

................................

..............................

Data Interface Connections Channel A

................................

..............................

Data Channel A Configuration

................................

............

Front Panel Indicators

Power LED

................................

..........

Video

Input LED’s

................................

...............................

Fibre Optic LED’s

................................

...............................

Low Speed Data LEDs

................................

.......................

Ethernet Operation

Physical Information

Dimen

sions

................................

.........

Mounting Details

................................

Removal / replacement from / to the Case

................................

.........................

Safety

Maintenance and Repair

AMG Systems Ltd. reserves the right to make changes to this

document without notice. The information herein is believed to

be acc

urate. No responsibility is assumed by AMG for its use.

Page

AMG4783E

Instruction

Sheet

D16828

02.doc

Introduction

Unit Functional Schematic

The

AMG4783E

transmits up to 8 video and 1

data signals to the

AMG4784E

It also receives 1 data signal

transmitted from the

AMG4784E

Ethernet connectivity is also

provided between the two

units

The

AMG4783E

transmits and receives the optical signals from both primary and secondary

optical channels. These optical channels are transmitted on the same optical fibre in opposite

directions, operating at different wavelengths. The primary c

hannel operates on 1550nm and the

secondary channel on 1310nm.

The

AMG4783E

receives and drops off a data signal transmitted from an

AMG4784E

receiver. It then inserts video and a data signal onto the outgoing optical signal. In normal operati

the video and data signals are transmitted on the primary output and the data received from the

primary input. The secondary optical input is independent and is regenerated on the secondary output.

At the

AMG4784E

receiver if the primary input si

gnal is not present, the unit will shut down the

secondary output to inform the

AMG4783E

that the primary signal route is not OK. The

AMG4783E

will then send out the video and data signals on its secondary output in the

opposite direction. As t

he primary input at the

AMG4784E

is not present the data signal will

now be taken from the secondary optical input, thus maintaining integrity of the data transmission.

Optical Connection

The

AMG4783E

is connected as illustrated below when u

sed with an

AMG4784E

receive unit acting as a point to point system.

AMG Systems Ltd. reserves the right to make

changes to this

document without notice. The information herein is believed to

be accurate. No responsibility is assumed by AMG for its use.

Page

AMG4783E

Instruction

Sheet

D16828

02.doc

Connections

Video Input Connections

No. of channels

................................

....

Connector

................................

............

75 ohm BNC Socket.

Input Impedance

................................

75 ohm terminated.

Input Level

................................

...........

1 volt p

p nominal

Frequency Response

...........................

10Hz to

7MHz.

Optical Connections

PRIMARY OPTO OUT

Connector

................................

............

LC/PC

Primary Optical Launch Power

............

5dBm

Wavelength

................................

..........

1550nm

Secondary Optical Sensitivity

..............

22dBm

Wavelength

................................

..........

1310nm

PRIMARY OPTO IN

Connector

................................

............

LC/PC

Primary Optical Sensitivity

...................

22dBm

Wavelength

................................

..........

1550nm

Secondary Optical Launch Power

.......

5dBm

Wavelength

................................

..........

1310nm

Power Connection

Connector Type

................................

...

2.1mm screw lock long power jack

–

centre positive

Connector Partno.

................................

Switchcraft S761K, AMG G16125

Supply Voltage

................................

.....

13.5 to 18.0 Volts DC.

Maximum Power

................................

10 Watts

Ethernet Connection

Ethernet Data Connector

....................

RJ45

Interface

................................

...............

Auto

negotiation up to 100BASE

TX full duplex

Ethernet Data Rate

..............................

Maximum 50Mbits/s total Ethernet traffic on fibre

Data and Audio Channel Connections

DATA CHANNEL A

Data Channel A

................................

...

1 channel

Dat

a Connector

................................

....

RJ45

Channel A Interface

.............................

On Board Data Interface

–

RS232, RS422 or RS485. Selected

by slide switch above the RJ45 connector.

RS232

–

switch position

high (closest to BNC connections)

RS422

–

switch position

–

middle

RS485

–

switch positio

–

low (furthest from BNC connections)

DATA CHANNEL B

Data Channel B

................................

...

Not Present

AMG Systems Ltd. reserves the right to make changes to this

document without notice. The information herein is believed to

be accurate. No responsibility is assumed by AMG for its use.

Page

AMG4783E

Instruction

Sheet

D16828

2.doc

Data and Audio Channel Configuration

The

AMG4783E

and rackmount equivalent

AMG4783ER

sends and receives data

to/from Cha

nnel A. Channel B is not available. Channel A is a single data interface selectable by the

user with the slide switch on the rear panel.

Data Interface Connections Channel A

Channel A

RJ45 Pin

No.

RS485

[sw

itch low]

RS422 [switch

mid]

RS232

[switch high]

Cat 5/6 Cable

Colour Code T568B

IN + (A)

GND

White/orange

(B)

Orange

White/green

Blue

White/blue

Green

IN/OUT + (A)

OUT + (A)

N/A

White/brown

IN/OUT

(B)

OUT

(B)

OUT

Bro

Note: (A) or (B) in brackets in above table refers to RS485 / RS422 data specification, not Channel A,

Channel B.

Data Channel A Configuration

Channel A is always present and allows for a RS232, RS422 (full duplex, four wire) or RS485 (half

duplex,

two wire) interface depending on the position of the switch located above the RJ45 connector.

The switch signifies the presence of the X16004 Low Speed Data/Audio Interface Board. If there are

LED's present on the RJ45 connector then an X16003 Ethernet Int

erface Board is fitted.

The data input for both the RS485 and the RS422 modes detects a tri

state input condition by

monitoring the differential voltage level across the input. A differential level below 600mV positive or

negative will be detected as a tr

state condition. A level above 600mV positive or negative will

detected as a logic 1 or logic zero respectively. It is important therefore to terminate the RS485 bus or

the RS422 input bus using 120Ωif a pre

bias is present on the RS485 or RS422 bus.

A large number of third party equipment manufacturers apply a

pre

bias on their RS485 bus. This pre

bias is applied by pulling one arm of the RS485 bus high (+5 volts) and the other arm low (0 volts)

using high value resistors within the third party equipment. In order to ensure that the AMG equipment

detects a tri

state condition, then these resistors should have a value above 5k

Ω. If the third party

bias resistors are less the 750Ωthe bus can be double or triple terminated as required to ensure that a

tri

state level is detected.

Note: The Data Channel A is shipped from the factory set up for RS485 operation unless otherwise

equested.

AMG Systems Ltd. reserves the right to make changes to this

document without notice. The information herein is believed to

be a

ccurate. No responsibility is assumed by AMG for its use.

Page

AMG4783E

Instruction

Sheet

D16828

02.doc

Front Panel Indicators

Power LED

Power

................................

...................

Green

unit powered

Off

no power applied to unit

Video Input LED’s

Video Present CH1

...........................

Green

video signal present on input BNC

R/G

channel present but no video on I/P BNC

Fibre Optic LED’s

Primary Opto Sync TX

.........................

Green

optical channel transmitting

Off

optical channel not transmitting

Primary Opto Sync RX

.........................

Green

optical channel receiving

Org

optical channel receiving but not sync.

Off

optical channel not receiving

Secondary Op

to Sync TX

....................

Green

optical channel transmitting

Off

optical channel not transmitting

Secondary Opto Sync RX

....................

Green

optical channel receiving

Org

optical channel receiving but not sync.

Off

optical channel not receiving

Low Speed Data LEDs

Channel A

Data Present TX (RS485 or RS422)

...

Green

logic zero (+V,

V) present on IN+, IN

Red

logic one (

V,V+) present on IN+, IN

Off

tri

state off or no connection on IN+, IN

Data Present TX (RS232)

....................

Green

logic zero (+V) present on input IN+

Red

logic transitions present on input IN+

Off

logic one (

V) present on input IN+

This represents the data signals being transmitted on the optical fibre

Data Present RX (RS485 or RS422)

...

Green

logic zero (+V,

V) present on OUT+, OUT

Red

gic one (

V,+V) present on OUT+, OUT

Off

tri

state off or no connection on OUT+, OUT

Data Present RX (RS232)

...................

Green

logic zero (+V) present on OUT+

Red

logic transitions present on OUT+

Off

logic one (

V) present on OUT+

This represents th

e data signals being received on the optical fibre

AMG Systems Ltd. reserves the right to ma

ke changes to this

document without notice. The information herein is believed to

be accurate. No responsibility is assumed by AMG for its use.

Page

AMG4783E

Instruction

Sheet

D16828

02.doc

Ethernet Operation

In order for the AMG system to transmit Ethernet signals, an onboard RJ45 Ethernet interface or

X16003 Ethernet interface adaptor should be fitted to both the Transmit unit and the R

eceive unit.

The Ethernet interface can operate at either 10Mbits/s half duplex, or 100Mbit/s full duplex, and data is

transmitted from one port the other port with the minimum of delay or buffering. The maximum

bandwidth (at 100Mbit/s full duplex) availa

ble for transmission across the fibre link is nominally

50MBit/s.

The 100BaseT port does not implement MDI/MDIX; it should be connected with a straight though

cable to an external switch port and with a cross over cable when connected directly to a PC or

DTE.

AMG Systems Ltd. reserves the right to make changes to this

document without notice. The information herein is believed to

be accurate. No responsibility is assumed by AMG for its use.

Page

AMG4783E

Instruction

Sheet

D16828

02.doc

Physical Information

Dimensions

Height

................................

...................

112mm

Width

................................

....................

170mm (excluding connectors)

Depth

................................

...................

70mm

Weight

................................

..................

1000grams

Mounting Details

The AMG unit is supplied with a clip

on mounting bracket which should be attached to a panel or wall

using 2 off 4.0mm s

crews. The unit is clipped into the mounting bracket, and is then held firmly in

position.

Removal / replacement from / to the Case

Note:

The AMG unit PCB's are static sensitive. Handle with proper care and use normal electrostatic

discharge (ESD) pro

cedures. Use properly grounded protection (for example, wrist straps) when

handling the PCB.

To remove units from the case to access the data expansion boards and the daughter boards, remove

the 2 or 4 fixing screws on the rear panel and slide the PCB's

out of the case.

Ensure that the fibres do not snag or get trapped.

To replace the PCB's into the case, slide the PCB's gently into the case aligning the boards with the

appropriate slots. Ensure that the fibre do not snag or get trapped.

Safety

AMG

Optical Fibre Products use Class 1 laser systems in accordance with EN 60825

2:2000.

It is always advisable to follow good practice when working with optical fibre systems. This includes:



Do not stare with unprotected eyes or with any unapproved collimat

ing device at fibre

ends or connector faces, or point them at other people.



Use only approved filtered or attenuating viewing aids

For other safety issues and advice on good practice associated with optical fibre systems, please see

EN 60825

2:2000 or you

r local safety officer.

Maintenance and Repair

There are no user serviceable parts within AMG products. See unit data sheet for full specification.

In case of problem or failure, please call your local support centre or contact:

AMG Systems Ltd.

The Omega Centre, Stratton Business Park, Biggleswade, Beds., SG18 8QB, UK.

Phone

+44 (0) 1767 600 777

Technical Support

+44 (0) 1767 604 491

techsupport@amgsystems.com

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Transmisor de AMG

AMG

AMG AMG4681R-CWDMn Manual de usuario

AMG

AMG AMG4647-ULTRA1 Manual de usuario

AMG

AMG AMG4627B Manual de usuario

AMG

AMG AMG4647BR Manual de usuario

AMG

AMG AMG4683ER Manual de usuario

AMG

AMG AMG4703E-SF Manual de usuario

AMG

AMG AMG5611R Manual de usuario

AMG

AMG AMG4781ER Manual de usuario

AMG

AMG AMG4713Bx-SF Manual de usuario

AMG

AMG AMG4784R Manual de usuario

AMG

AMG AMG3747BE Manual de usuario

AMG

AMG AMG4707AEG Manual de usuario

AMG

AMG AMG4643-DR-SF Manual de usuario

AMG

AMG AMG4687BR Manual de usuario

AMG

AMG AMG4713E Manual de usuario

AMG

AMG AMG5813R Manual de usuario

AMG

AMG AMG5901 Manual de usuario

AMG

AMG AMG4683E Manual de usuario

AMG

AMG AMG5803A966G-DF Manual de usuario

AMG

AMG AMG3727BE Manual de usuario

AMG

AMG AMG5513A6B9 Manual de usuario

AMG

AMG AMG5713A6B9-HP Manual de usuario

AMG

AMG AMG5613A9R Manual de usuario

AMG

AMG AMG4783RN-CWDMn Manual de usuario

Manuales populares de Transmisor de otras marcas

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manual del propietario

Honeywell

Honeywell 5816WMBR Manual de usuario

Kamstrup

Kamstrup READy MTU Instrucciones de funcionamiento

Omega

Omega ZW Series Manual de usuario

ABB

ABB Field 264H Guía

Alinco

Alinco DJ-V17T Manual de usuario

Dejero

Dejero EnGo 3x Manual de usuario

Rosemount

Rosemount 4600 Manual de usuario

Speaka Professional

Speaka Professional 2342740 Manual de usuario

trubomat

trubomat GAB 1000 Manual de usuario

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manual de usuario

Rondish

Rondish UT-11 Manual de usuario

MG 10JRE Manual de usuario

Burkert

Burkert 8177 Manual de usuario

Firetide

Firetide HotPort 3203 Manual

Tele Radio

Tele Radio T9-02 Manual de usuario

Rotronic

Rotronic HygroFlex HF3 Series Manual de usuario

Jamara

Jamara FCX6 Pro Tel Manual de usuario