Allen-Bradley PanelView Plus 7 Manual de usuario

Migrating PanelView Standard Applications to

PanelView Plus 7

Migration Guide

Original Instructions

Important User Information

Read this document and the documents listed in the additional resources section about installation, configuration, and

operation of this equipment before you install, configure, operate, or maintain this product. Users are required to

familiarize themselves with installation and wiring instructions in addition to requirements of all applicable codes, laws,

and standards.

Activities including installation, adjustments, putting into service, use, assembly, disassembly, and maintenance are

required to be carried out by suitably trained personnel in accordance with applicable code of practice.

If this equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may

be impaired.

In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages resulting from

the use or application of this equipment.

The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many variables and

requirements associated with any particular installation, Rockwell Automation, Inc. cannot assume responsibility or

liability for actual use based on the examples and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits, equipment, or

software described in this manual.

Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell Automation,

Inc., is prohibited.

Throughout this manual, when necessary, we use notes to make you aware of safety considerations.

Labels may also be on or inside the equipment to provide specific precautions.

WARNING: Identifies information about practices or circumstances that can cause an explosion in a hazardous

environment, which may lead to personal injury or death, property damage, or economic loss.

ATTENTION: Identifies information about practices or circumstances that can lead to personal injury or death, property

damage, or economic loss. Attentions help you identify a hazard, avoid a hazard, and recognize the consequence.

IMPORTANT Identifies information that is critical for successful application and understanding of the product.

SHOCK HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that dangerous

voltage may be present.

BURN HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that surfaces may

reach dangerous temperatures.

ARC FLASH HAZARD: Labels may be on or inside the equipment, for example, a motor control center, to alert people to

potential Arc Flash. Arc Flash will cause severe injury or death.Wear proper Personal Protective Equipment (PPE). Follow ALL

Regulatory requirements for safe work practices and for Personal Protective Equipment (PPE).

Rockwell Automation Publication 2711P-AP006C-EN-P - November 2018 3

Where to Start

We Can Get You from Here …

… to Here

PanelView™ Standard

SLC™500 Controller PLC-5®Controller ControlLogix®

PanelView Plus 7 Terminal

SLC 500 Controller PLC-5 Controller ControlLogix

4Rockwell Automation Publication 2711P-AP006C-EN-P - November 2018

Where to Start

Follow this path to migrate your PanelView Standard terminal and application

to the PanelView Plus 7 terminal platform.

Chapter 1

Things to Know Before

You Migrate

Chapter 2

Select a Terminal

Replacement

Chapter 3

Import Your Application

Chapter 4

Review the Application

Conversion Log

Chapter 5

Review Object Mapping

Chapter 9

Optimize Runtime

Performance

Appendix A

Advanced Object

Editing

Chapter 6

Review Unsupported

Features

Chapter 7

Qualify the Runtime

Application

Before you update the migrated

application, review the conversion

log details and the remaining

chapters. If you determine that the

conversion operation would not be

feasible, you can use the conversion

services that are provided by

Rockwell Automation. For more

information, see Conversion

Services, publication GMSC10-

PP009.

Chapter 8

Create the Runtime

Application

Rockwell Automation Publication 2711P-AP006C-EN-P - November 2018 5

Table of Contents

Preface

Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Summary of Changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Required Software. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Additional Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Chapter 1

Things to Know before You

Migrate

Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

External Fonts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Retain Last States on Startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Unsupported Characters in Tag Names and Addresses . . . . . . . . . . . 12

Bit Array Tags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

String Tags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Alarm Trigger Tags. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Bit Position Triggers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Least Significant Bit Triggers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Alarm Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Tags Assigned to Message Connections . . . . . . . . . . . . . . . . . . . . . . . . . 15

Chapter 2

Select a Terminal Replacement Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Before You Begin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Follow These Steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Selecting a Terminal Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Catalog Number Conversion Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

PanelView Standard 300 and 300 Micro Terminals

Conversions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

PanelView Standard 550 Terminals Conversions. . . . . . . . . . . . . 20

PanelView Standard 600 Terminals Conversions. . . . . . . . . . . . . 24

PanelView Standard 900 Terminals Conversions. . . . . . . . . . . . . 28

PanelView Standard 1000 Terminals Conversions. . . . . . . . . . . . 34

PanelView Standard 1400 Terminals Conversions. . . . . . . . . . . . 40

PanelView Enhanced 1000e, 1200e, 1400e Terminals

Conversions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Legacy Communication Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Adapter Kit Conversion Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Function Key Comparisons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Installing a PanelView Plus 7 Terminal. . . . . . . . . . . . . . . . . . . . . . . . . . 46

Chapter 3

Import Your Application Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Before You Begin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

What You Need. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

6Rockwell Automation Publication 2711P-AP006C-EN-P - November 2018

Table of Contents

Follow These Steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Import Application. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Post Conversion Tips. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Chapter 4

Review the Application

Conversion Log

Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Before You Begin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

What You Need. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Follow These Steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

About the Conversion Log. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Open the Conversion Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Review the Conversion Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Conversion Messages You Can Ignore. . . . . . . . . . . . . . . . . . . . . . . 56

RSLinx Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Screen and Object Conversion Messages. . . . . . . . . . . . . . . . . . . . . 57

Tag Conversion Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Alarm Conversion Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Chapter 5

Review Object Mapping Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Before You Begin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

What You Need. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Follow These Steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Reviewing Object Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Reviewing Data Type Mapping. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Reviewing Mapping of Communication Networks. . . . . . . . . . . . . . . 63

Chapter 6

Review Unsupported Features Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Before You Begin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

What You Need. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Follow These Steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Reviewing Unsupported Objects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Reviewing Unsupported Tags and Controls . . . . . . . . . . . . . . . . . . . . . 66

Reviewing Unsupported Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Chapter 7

Qualify the Runtime Application Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Before You Begin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

What You Need. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Follow These Steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Review Diagnostic Lists. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Configure the Runtime Diagnostic Display. . . . . . . . . . . . . . . . . . . . . . 71

Review Error States for Graphic Objects . . . . . . . . . . . . . . . . . . . . . . . . 73

Rockwell Automation Publication 2711P-AP006C-EN-P - November 2018 7

Table of Contents

Configure Communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

ControlNet Communication. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Test Run Graphic Displays. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Test Run the Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

Chapter 8

Create the Runtime Application Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

Before You Begin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

What You Need. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

Follow These Steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

Create the Runtime Application. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

Download the Runtime Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

Download Application Using Ethernet Connection . . . . . . . . . . 84

Download Application Using External Storage. . . . . . . . . . . . . . . 88

Run the Application. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

Chapter 9

Optimize Runtime Performance Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93

Before You Begin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93

What You Need. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93

Follow These Steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94

Benchmarking Performance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94

Reviewing Tag Update Rate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95

Measure Performance of Display Changes . . . . . . . . . . . . . . . . . . . . . . . 96

Reviewing Background Updates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97

Global Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97

Alarms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98

Information Messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98

Optimize Tags for Network Performance . . . . . . . . . . . . . . . . . . . . . . . 98

About the Tag Converter Wizard. . . . . . . . . . . . . . . . . . . . . . . . . . . 99

Export the HMI Tag Database. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100

Export Graphic Displays to XML File . . . . . . . . . . . . . . . . . . . . . . 103

Export Alarms to XML File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107

Run the Tag Converter Wizard. . . . . . . . . . . . . . . . . . . . . . . . . . . . 109

Reimport the Display XML File . . . . . . . . . . . . . . . . . . . . . . . . . . . 112

Reimport the Alarms XML File. . . . . . . . . . . . . . . . . . . . . . . . . . . . 116

Appendix A

Advanced Object Editing Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119

Property Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119

Edit Multiple Objects. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120

Object Explorer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123

Substitute Tags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128

8Rockwell Automation Publication 2711P-AP006C-EN-P - November 2018

Table of Contents

Notes:

Rockwell Automation Publication 2711P-AP006C-EN-P - November 2018 9

Preface

Introduction This document provides guidelines and procedures for migrating a PanelView™

Standard terminal application to the PanelView Plus 7 terminal platform. The

procedures and guidelines cover the following:

• Selecting and optionally installing a PanelView Plus 7 terminal

replacement

• Importing your PanelView Standard application into the FactoryTalk®

View Machine Edition software

• Updating the imported application and ladder logic, as necessary, for

compatibility with FactoryTalk View Machine Edition software

• Reviewing unsupported features

• Verifying the correct operation of the imported application on the

PanelView Plus 7 terminal

• Measuring and improving performance of the migrated application

The procedures and guidelines are designed to make the migration process as

easy as possible.

The beginning of most chapters contains the following information. Read

these sections carefully before beginning work in each chapter.

• Before You Begin - This section lists the steps that must be completed

and decisions that must be made before starting the chapter. The

chapters in this quick start must be completed or reviewed in the order

in which they appear.

• What You Need - This section lists the items that are required to

complete the steps in the current chapter. These items include, but are

not limited to, hardware and software.

• Follow These Steps - This section illustrates the path or steps in the

current chapter.

Also note that the electronic version of this publication contains links to other

publications for easier navigation and reference.

Summary of Changes This publication contains new and updated information as indicated in the

following table.

Audience This quick start was created to assist a user familiar with Rockwell Automation®

HMI products on how to convert existing PanelView Standard applications to

FactoryTalk View Machine Edition applications that run on PanelView Plus 7

terminals.

Topic Pages

Added information about the availability of conformal coating for the 15 in.

combination keypad and touch terminal (2711P-B15C22D9PK).

37…39

10 Rockwell Automation Publication 2711P-AP006C-EN-P - November 2018

Preface

Required Software The table lists the software that is required to convert a PanelView Standard

application to a PanelView Plus 7 application.

Additional Resources These documents contain additional information about related products from

Rockwell Automation.

You can view or download publications at

http://www.rockwellautomation.com/global/literature-library/overview.page.

To order paper copies of technical documentation, contact your local

Allen-Bradley distributor or Rockwell Automation sales representative.

Software Terminal Type Software Version

FactoryTalk View Studio, which includes:

FactoryTalk View Machine Edition

RSLinx® Enterprise

PanelView Plus 7 Standard 4.0 or later

PanelView Plus 7 Performance 5.1 or earlier

PanelView Plus 7 Performance 6.0 or later

PanelBuilder®32 — 3.83 or earlier

Resource Description

Adapter Kit for PanelView 5500 and PanelView Plus 7

Performance Terminals Installation Instructions,

publication VIEW-IN002

Provides information on how to install a PanelView

Plus 7 terminal into an existing cutout from a

PanelView Standard terminal.

Legacy PanelViewTerminals to PanelView Plus 7Terminals

Catalog Number Conversions Migration Guide, publication

2711P-AP005

Provides information on how to convert legacy 2711

PanelView Standard terminals and 2711E PanelView

Enhanced terminals to the new generation terminals:

PanelView Plus 7 Standard terminals and PanelView

Plus 7 Performance terminals.

PanelView Plus 7 PerformanceTerminals User Manual,

publication 2711P-UM008

Provides information on how to install, operate,

configure, and troubleshoot PanelView Plus 7

performance terminals.

PanelView Plus 7 Standard Terminals User Manual,

publication 2711P-UM007

Provides information on how to install, operate,

configure, and troubleshoot PanelView Plus 7

standard terminals.

Visualization Solutions Selection Guide,

publication VIEW-SG001

Provides an overview of visualization products,

including PanelView Plus 7 terminals.

FactoryTalk View Studio online help Provides information and procedures on how to create

FactoryTalk View Machine Edition applications and

supported features.

Industrial Automation Wiring and Grounding Guidelines,

publication 1770-4.1

Provides general guidelines on how to install a

Rockwell Automation industrial system.

Product Certifications website, rok.auto/certifications Provides declarations of conformity, certificates, and

other certification details.

Otros manuales para PanelView Plus 7

Tabla de contenidos

Otros manuales de Terminal táctil de Allen-Bradley

Allen-Bradley

Allen-Bradley PanelView 2711C-F2M Manual de usuario

Allen-Bradley

Allen-Bradley PanelView 5500 Manual de usuario

Allen-Bradley

Allen-Bradley PanelView 800 2711R-T4T Manual de usuario

Allen-Bradley

Allen-Bradley PanelView 800 Manual de usuario

Allen-Bradley

Allen-Bradley 2711-K6C series Manual de usuario

Allen-Bradley

Allen-Bradley MobileView 2711T-B10R1K1 Manual de usuario

Allen-Bradley

Allen-Bradley PV300 Micro Manual de usuario

Allen-Bradley

Allen-Bradley 2711-K5A series Manual de usuario

Allen-Bradley

Allen-Bradley C Series Manual de usuario

Allen-Bradley

Allen-Bradley PanelView C200 Manual de usuario

Allen-Bradley

Allen-Bradley PanelView Plus 6 700 Manual de usuario

Allen-Bradley

Allen-Bradley PanelView Plus 7 Manual de usuario

Allen-Bradley

Allen-Bradley FLEX 5000 Manual de usuario

Allen-Bradley

Allen-Bradley 2711P Manual de instrucciones

Allen-Bradley

Allen-Bradley PanelView 2711P-RW1 Manual de usuario

Allen-Bradley

Allen-Bradley FLEX I/O SCANport 1203-FB Manual de usuario

Allen-Bradley

Allen-Bradley PanelView 1200 Manual de usuario

Allen-Bradley

Allen-Bradley PanelView Plus 7 Manual de usuario

Allen-Bradley

Allen-Bradley PanelView Plus 400 Manual de usuario

Allen-Bradley

Allen-Bradley 1770-T1 Manual de usuario

Allen-Bradley

Allen-Bradley 8510SA-TP Series Manual de usuario

Allen-Bradley

Allen-Bradley DeviceNet 1790D-T16BV0 Manual de usuario

Allen-Bradley

Allen-Bradley 1797-TB3S Manual de usuario

Allen-Bradley

Allen-Bradley PanelView Plus 6 Manual de usuario

Manuales populares de Terminal táctil de otras marcas

Wincor Nixdorf

Wincor Nixdorf iPOS plus Advanced Manual de usuario

Ingenico

Ingenico AXIUM EX4000 Manual de usuario

Heisei Electronics

Heisei Electronics Q-POS 815 Manual de usuario

Amano

Amano MTX-15 Manual de usuario

FLOWBIRD

FLOWBIRD CWT Compact Touch Manual de usuario

Demco

Demco SP7 Manual de usuario

Lathem

Lathem PC600 Series Manual de usuario

Partner

Partner MF-2352 Manual de usuario

NCR

NCR RealPOS 7460-2 Manual

Simrad

Simrad MS50 Instrucciones de montaje

Unitech

Unitech MR350 MKII Guía de inicio rápido

Jungheinrich

Jungheinrich WMT 210 Manual de usuario

Motorola

Motorola MTP850 Manual de usuario

YASKAWA

YASKAWA 62H-MDC0 Manual de usuario

MVG industries

MVG industries NeptuLink Manual de usuario

Price Industries Limited

Price Industries Limited FDC Manual de instrucciones

Honeywell

Honeywell TemaKey Manual de usuario

EBN

EBN BPC65-B-A16G Manual de usuario