Allen-Bradley ControlNet 1747-SCNR Manual de usuario

Publication 1747-5.36 - May 2000

Installation Instructions

SLC ControlNet Scanner Module

Catalog Number 1747-SCNR

Use this document to help you install the ControlNet™ 1747-SCNR

Scanner module.

For information about See page

preventing electrostatic discharge 2

compliance to European Union Directives 2

related publications 3

module features 4

preparing the module for installation 5

selecting the ControlNet node address 6

inserting the 1747-SCNR scanner into the chassis 6

connecting to a ControlNet network 8

cables 10

applying chassis power 11

status indicators 15

specifications 17

Allen-Bradley Replacements

2SLC ControlNet Scanner Module

Publication 1747-5.36 - May 2000

Prevent Electrostatic Discharge

The scanner module is sensitive to electrostatic discharge.

Compliance to European Union Directives

If this product has the CE mark, it is approved for installation within

the European and EEA regions. It has been designed and tested to

meet the following directives.

EMC Directive

This product is tested to meet Council Directive 89/336/EEC

Electromagnetic Compatibility (EMC) and the following standards, in

whole or in part, documented in a technical construction file:

•EN 50081-2 EMC — Generic Emission Standard, Part 2 —

Industrial Environment

•EN 50082-2 EMC — Generic Immunity Standard, Part 2 —

Industrial Environment

This product is intended for use in an industrial environment.

ATTENTION

Electrostatic discharge can damage integrated circuits or

semiconductors if you touch backplane connector pins. Follow

these guidelines when you handle the module:

•touch a grounded object to discharge static potential

•wear an approved wrist-strap grounding device

•do not touch the backplane connector or connector pins

•do not touch circuit components inside the module

•if available, use a static-safe work station

•when not in use, keep the module in its static-shield bag

SLC ControlNet Scanner Module 3

Publication 1747-5.36 - May 2000

Low Voltage Directive

This product is tested to meet Council Directive 73/23/EEC Low

Voltage by applying the safety requirements of EN 61131-2

Equipment Requirements and Tests.

For specific information required by EN 61131-2, see the appropriate

sections in this publication as well as the following Allen-Bradley

publications:

•Industrial Automation Wiring and Grounding Guidelines For

Noise Immunity, publication 1770-4.1

•Guidelines For Handling Lithium Batteries, publication AG-5.4

•Automation Systems Catalog, publication B113

This equipment is classified as open equipment and must be

installed (mounted) in an enclosure as a means of providing safety

protection.

Related Publications

For software configuration information, refer to the ControlNet

1747-SCNR Reference Manual, publication 1747-6.23.

For planning and installation information, refer to the ControlNet

Cable System Planning and Installation Manual, publication

1786-6.2.1. If you need a copy of this manual, access the

Automation Bookstore website at

http://www.theautomationbookstore.com or the Manuals On line

website at http://www.ab.com/manuals.

For information on terminating ControlNet coaxial cables, refer to

Terminating Your ControlNet Coaxial Cables, CD number

CNET-DM001A-EN-C.

Allen-Bradley Replacements

4SLC ControlNet Scanner Module

Publication 1747-5.36 - May 2000

Identify Scanner Module Features

Use this illustration to identify the features of the 1747-SCNR

Scanner module.

Node Address and Status Display

Displays scanner node address and status

Module Status Indicator

Indicates whether the device is powered and is

functioning properly

ControlNet Redundant Media Ports

BNC connectors (Channels A and B)

Channel B

Status Indicator

Channel A

Status Indicator

ControlNet Network

Access Port

(NAP)-RJ45 connector

30751-M

SLC ControlNet Scanner Module 5

Publication 1747-5.36 - May 2000

Prepare for Module Installation

Before you install your module, you need the following items:

Before you install the module, you must know how to:

•program and operate an Allen-Bradley SLC 500 programmable

controller

•install and configure the devices on your ControlNet network

Make Sure That Your Processor and Scanner Are Compatible

The 1747-SCNR Scanner module fits in any slot of the chassis except

for the left-most slot of the first chassis, which is reserved for either

the SLC 500 processor or the SLC ControlNet adapter.

Reference

Manual

ControlNet

1747-SCNR

(Cat. No. 1747-SCNR)

Personal Computer with

MicrosoftWindows

RSNetWorx for

ControlNet,

catalog number

9357-CNETL3 1747-SCNR Scanner Module

Reference Manual,

publication 1747-6.23

SLC1746 chassis with SLC

5/02, 5/03, 5/04, or 5/05 processor and

the appropriate configuration software

(RSLogix 500)

ControlNet 1784-PCC (shown), or

1784-KTCX15, or 1770-KFC15

41523

Allen-Bradley Replacements

6SLC ControlNet Scanner Module

Publication 1747-5.36 - May 2000

Select the ControlNet Node Address

Select the ControlNet node address of the 1747-SCNR by setting the

two 10-digit rotary switches on the top of the scanner. Valid switch

settings range from 01 through 99. Zero (00) is not a valid node

address.

Important: Since 00 is the default value from manufacturing, you

must change the default value when using the

scanner for the first time.

Insert the 1747-SCNR Scanner Into the Chassis

To insert the 1747-SCNR Scanner the SLC chassis:

1. Turn off the SLC chassis power supply.

Important: If you disconnect the ac power, you lose the chassis

ground. Electrostatic damage (ESD) protection is lost.

ATTENTION

Do not install the 1747-SCNR Scanner module with the

chassis power supply on. Installing the module with the

chassis power supply on may damage the module.

Top View of Module

10-digit rotary switches: ones digit

10-digit rotary switches: tens digit

30752

SLC ControlNet Scanner Module 7

Publication 1747-5.36 - May 2000

2. Select a slot for the module in the chassis. Choose any slot

except the left-most slot of the first chassis, which is reserved

for either the SLC 500 processor.

3. Insert the module into the slot you have selected. We

recommend that you insert the 1747-SCNR Scanner as close to

the chassis power supply as possible.

4. Apply firm, even pressure to seat the module in the I/O

chassis backplane connectors.

5. Restore power to the SLC chassis.

30801-M

Allen-Bradley Replacements

8SLC ControlNet Scanner Module

Publication 1747-5.36 - May 2000

Connect to a ControlNet Network

Connect the 1747-SCNR Scanner module to a ControlNet network

via a tap with a 1 m (39.4 in.) drop cable.

Four Allen-Bradley ControlNet taps are available from Rockwell

Automation as shown below.

We recommend that you use a tap with a straight connector—

1786-TPS or 1786-TPYS—when you attach a ControlNet 1747-SCNR

Scanner to a ControlNet network.

Important: Allen-Bradley ControlNet taps contain passive

electronics and must be purchased from Rockwell

Automation for the network to function properly.

After terminating your network segments, connect your node to the

network.

Straight T-tap Straight Y-tap Right-angle T-tap Right-angle Y-tap

1786-TPS 1786-TPYS 1786-TPR 1786-TPYR 20094-M

Redundant media

Nonredundant media

30802-M

SLC ControlNet Scanner Module 9

Publication 1747-5.36 - May 2000

Remove the tap’s dust cap—located on the straight or right-angle

connector—and set it aside.

For detailed information about planning and installing your

ControlNet system, see the following information sources.

If your network supports Connect the tap’s straight or right-angle connector

nonredundant media to the channel A connector on the scanner—channel B is

not used.1

redundant media from trunk-cable A to channel A on the scanner and

from trunk-cable B to channel B on the scanner.

1. Rockwell Automation recommends using channel A for nonredundant media.

Source Source Number

ControlNet Coax Cable System Planning and Installation Manual 1786-6.2.1

ControlNet Media System Component List AG-2.2

ControlNet Coax Tap Installation Instructions 1786-5.7

ControlNet Network Access Cable Installation Instructions 1786-2.6

ControlNet Repeater Installation Instructions 1786-2.7

Industrial Automation Wiring and Grounding Guidelines 1770-4.1

Terminating Your ControlNet Coaxial Cables CNET-DM001A-EN-C

Allen-Bradley Replacements

10 SLC ControlNet Scanner Module

Publication 1747-5.36 - May 2000

Cables

Several types of RG-6 quad-shield cables may be appropriate for

your ControlNet installation—depending on the environment factors

associated with your application and installation site.

The following Allen-Bradley ControlNet cable system components

are available from Rockwell Automation:

Important: Install all wiring for your ControlNet system in

accordance with the regulations contained in the

National Electronic Code (or applicable country

codes), state codes, and applicable municipal codes.

For detailed information about ControlNet cabling, see the

ControlNet System Overview, publication 1786-2.9 and the

publications listed in the table on the previous page.

Item1Cat. No.

ControlNet Coax Tool Kit - ControlNet Coax Tool (enables you to make

successful coaxial cables)

1786-CTK

Coax Tap Kit Right-angle T-tap

Straight T-tap

Right-angle Y-tap

Straight Y-tap

1786-TPR

1786-TPS

1786-TPYR

1786-TPYS

Repeaters Dual channel coaxial repeater 1786-RPCD

Fiber Optic Repeaters

Low-voltage dc coax adapter 1786-RPA

Short-range fiber module 1786-RPFS

Medium-range fiber module 1786-RPFM

RG-6 Quad Shield Cable Standard-PVC CM-CL2 1786-RG6

ControlNet Network Access Cable–3.05 m (10 ft) 1786-CP

BNC Connectors Barrel (plug to plug) 1786-BNCP

BNC/RG-6 plug 1786-BNC

Bullet (jack to jack) 1786-BNCJ

Isolated-bulkhead (jack to jack) 1786-BNCJI

Terminators (BNC-75Ω) 1786-XT

1. For a complete list of Allen-Bradley ControlNet cable system components that are available from

Rockwell Automation and cable system components available from other suppliers, see the ControlNet

Cable System Component List, publication AG-2.2.

Otros manuales para ControlNet 1747-SCNR

Tabla de contenidos

Otros manuales de Unidad de control de Allen-Bradley

Allen-Bradley

Allen-Bradley 1772-MJ Manual de operación

Allen-Bradley

Allen-Bradley FLEX I/O 1794-ID2 Manual de usuario

Allen-Bradley

Allen-Bradley Series B Manual de usuario

Allen-Bradley

Allen-Bradley D Series Manual de usuario

Allen-Bradley

Allen-Bradley MicroLogix 1762-IQ8 Manual de usuario

Allen-Bradley

Allen-Bradley 1771-QDC Manual de usuario

Allen-Bradley

Allen-Bradley ControlLogix 1756-OA8 Manual de usuario

Allen-Bradley

Allen-Bradley ControlNet 1786-RPFS Manual de usuario

Allen-Bradley

Allen-Bradley 1794-OA8K Manual de usuario

Allen-Bradley

Allen-Bradley 1440-DYN02-01RJ Manual de usuario

Allen-Bradley

Allen-Bradley 1746-HSTP1 Manual de usuario

Allen-Bradley

Allen-Bradley XM-124 Manual de usuario

Allen-Bradley

Allen-Bradley ControlLogix 1756-DMD30 Manual de usuario

Allen-Bradley

Allen-Bradley FLEX I/O 1794-IV32 Manual de usuario

Allen-Bradley

Allen-Bradley Entek XM-123 Manual de usuario

Allen-Bradley

Allen-Bradley PowerFlex 20-HIM-A3 Manual de usuario

Allen-Bradley

Allen-Bradley 1771-OBN Manual de usuario

Allen-Bradley

Allen-Bradley ControlLogix 1756-ENBT Manual de usuario

Allen-Bradley

Allen-Bradley ArmorBlock 1732E-OB16M12R Manual de usuario

Allen-Bradley

Allen-Bradley ControlNet 1786-RPFM Manual de usuario

Allen-Bradley

Allen-Bradley Compact 1769-OB32 Manual de usuario

Allen-Bradley

Allen-Bradley ControlNet FLEX Ex 1797-BCNR Manual de usuario

Allen-Bradley

Allen-Bradley ControlLogix 1756-OX8I Manual de usuario

Allen-Bradley

Allen-Bradley Kinetix 2000 Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario