Allen-Bradley 1771-OD Guía de instalación y uso

AC (120V) Isolated Output Module

Cat. No. 1771-OD

Installation Data

This document provides information on:

important pre–installation considerations

power supply requirements

initial handling procedures

installing the module

using the module indicators for troubleshooting

replacing the fuse

module specifications

An output from this module can drive an Allen–Bradley Size 5 motor

starter, provided its supply voltage does not drop below 105V ac. The

maximum load current the module can deliver is 2A per channel, not to

exceed 6A total per module.

The switching device in the output circuit is a triac. There is a small

leakage current in the off state due to both triac and capacitive

characteristics. The maximum leakage current per output is 5mA at

138V ac. Nominal leakage current is 1mA. The on–state voltage drop

across the output terminals is no more than 2.0V ac at 100mA.

The triac needs a minimum of 60mA load current to stay on. If your

device pulls less than 60mA, the triac will not operate. The total

continuous current the module supports is 6A (2A maximum per channel).

If this rating is exceeded, the module overheats and damage may occur.

To The Installer

Pre-installation Considerations

AC (120V) Isolated Output Module

(Cat. No. 1771-OD)

Installation Data

Suppression

Surge suppression circuitry is provided for the output triacs of this module.

To suppress high–voltage transients from the ac line, a metal–oxide

varistor (MOV) is provided between each set of terminals on the module.

In each output circuit, an RC network limits the magnitude of voltage

transients that may occur when a device is wired in parallel or series with

hard contacts.

Loads with inductive characteristics may require additional suppression

devices. The impedance characteristic of the load is the most important

factor in selecting a suppression device; thus no single suppression device

can be recommended for every possible load. See Table A for acceptable

suppression devices for typical loads.

Table A

Allen-Bradley

Suppressors

Allen-Bradley Equipment Suppressor Catalog Number

Motor Starter Bulletin 509 599-K041

Motor Starter Bulletin 709 1401-N101

Relay Bulletin 700 Type N or P 700-N5/700N92

Miscellaneous 700-N243

1 For starters with 120V ac coils

2 Maximum coil voltage 150V ac or dc

3 Bulletin 700-N24 is a universal surge suppressor. You can use it on electromagnetic

devices with the limitation of 35 sealed VA, 150V.

The isolated output module is powered by the power supply connected to

the I/O chassis backplane. The module requires a maximum current of

225mA from the +5V dc output of this supply. Total the current

requirements of this module with the other modules in the I/O chassis to

avoid overloading the supply or the I/O chassis backplane.

Power Requirements

AC (120V) Isolated Output Module

(Cat. No. 1771-OD)

Installation Data

The ac output module is shipped in a static–shielded bag to guard against

electrostatic discharge damage. Observe the following precautions when

handling the module.

ATTENTION: Remove power from the 1771 I/O chassis

backplane and wiring arm before removing or installing an I/O

module.

Failure to remove power form the backplane or wiring arm

could cause module damage, degradation of performance, or

injury.

Failure to remove power from the backplane could cause

injury or equipment damage due to possible unexpected

operation.

Touch a grounded object to rid yourself of charge before handling the

module.

Do not touch the backplane connector or connector pins.

When you configure or replace internal components, do not touch other

circuit components inside the module. If available, use a static–safe

work station.

When not in use, keep the module in its static–shield bag.

In this section we tell you how to key your I/O chassis, install your module

and make your wiring connections

Module Location in the I/O Chassis

Group your modules to minimize adverse effects from radiated electrical

noise and/or heat. We recommend the following.

Group analog input and low voltage dc modules away from ac modules

or high voltage dc modules to minimize electrical noise interference.

Place analog input modules and other I/O modules sensitive to heat

away from slot power supplies to minimize adverse heat effects.

Initial Handling Procedures

Installing

our Module

AC (120V) Isolated Output Module

(Cat. No. 1771-OD)

Installation Data

Keying the I/O Chassis

Use the plastic keying bands, shipped with each I/O chassis, to key your

I/O slots to accept only this type of module. Place keying bands between

these numbers labeled on the upper backplane connector:

between 4 and 6

between 30 and 32

Slots on the rear edge of the circuit board are matched to these slots to

allow insertion of the module. You can key any connector in an I/O chassis

to receive this module except for the left–most connector reserved for

adapter or processor modules.

ATTENTION: A module inserted into a wrong slot could be

damaged by improper voltages connected through the wiring

arm. Use keying bands to prevent damage to the module.

Inserting the Module into the Chassis

1. Position the module so that the circuit board on the rear of the module

lines up with the top and bottom card guides in the chassis.

2. Slide the module into the chassis.

3. Press firmly to seat the module in the chassis backplane connector.

4. Swing the module locking latch down into place over the front of the

module.

Connecting Wiring to the module

You make connections to the module through the 1771–WD field wiring

arm shipped with the module. The arm pivots on the chassis to connect

with the 12 terminals on the front of the module (Figure 1). The wiring

arm allows the module to be removed from the chassis without

disconnecting wiring.

1. Make certain all power is removed from the module before making

wiring connections.

2. Swing the wiring arm up into position on the front of the module. The

locking tab on the module will secure it into place.

3. Make your connections to the field wiring arm as shown in Figure 1.

(Use the label on the front of the wiring arm to identify your wiring.)

AC (120V) Isolated Output Module

(Cat. No. 1771-OD)

Installation Data

ATTENTION: The field wiring arm terminal identification

number is not the same as the number of the bit which controls

that output.

You should identify the labels on the wiring arm with the name or number

of the device connected at each terminal.

Figure 1

Connection

Diagram for 1771-OD Isolated Output Module

L1 L2

120V ac

Supply

Load

Output 0A

Output 0B

Output 1A

Output 1B

Output 2A

Output 2B

Output 3A

Output 3B

Output 4A

Output 4B

Output 5A

Output 5B

10593-I

You can use an output of the 1771–OD module to drive an input of a 120V

ac input module (1771–IA, –IA2, –ID, –IAD) to indicate status of turning

on a motor starter, for example (Figure 2). However, you must add a 2.5K

ohm, 10W resistor (or an Electrocube snubber, pt. no. RG-1676-1) between

the output and L2 (common). Inputs configured with the output module are

not isolated from each other (except for 1771–IAD inputs).

ATTENTION: Do not connect the 1771–OD output channels

in series. Doing so can result in distortion of the output

waveform causing the output devices to chatter.

AC (120V) Isolated Output Module

(Cat. No. 1771-OD)

Installation Data

Figure 2

Driving

an Input with an Output

AC/DC (120V) Input Module

Cat. No. 1771-IAD

Input 00

Input 01

Input 02

Input 03

Input 04

Input 05

Input 06

Input 07

Input 10

Input 16

Input 11

Input 12

Input 13

Input 14

Input 15

Input 17

L1 L2

AC (120V) Isolated

Output Module

Cat. No. 1771-OD

AC (120V) Isolated

Output Module

Cat. No. 1771-OD

120V ac

Supply L1 L2

120V ac

Supply

120V AC Input Module

Cat. No. 1771-IA, -IA2

2K ohm

20 Watt

Resistor

10594-I

2.5K ohm

10 Watt

Resistor

The module has 12 status indicators (Figure 3). The top 6 indicators show

the state of each output and are driven by the logic circuitry on the

programmable controller side of the module. These indicators light when

their corresponding outputs are energized.

The bottom 6 indicators display a blown–fuse condition at the respective

output regardless of the state of the output. These indicators are driven by

your power supply.

Interpreting the Status

Indicators

AC (120V) Isolated Output Module

(Cat. No. 1771-OD)

Installation Data

Figure 3

Status

Indicators

Red Output

Indicators

Status

Clear Fuse Blown

Indicators

ISOLATED

AC OUTPUT

10595-I

Replacing a Fuse

Each module output is individually fused. You can easily access the

module fuses by removing the front component–side cover.

ATTENTION: Remove power from the 1771 I/O chassis

backplane and wiring arm before removing or installing an I/O

module.

Failure to remove power from the backplane could cause

injury or equipment damage due to possible unexpected

operation.

Failure to remove power from the backplane or wiring arm

could cause module damage, degradation of performance, or

injury.

If a blown fuse occurs:

1. Turn off power to the I/O chassis backplane.

2. Pivot the wiring arm away from the module and pull the module from

the I/O chassis.

3. Remove the front component side cover from the module by

removing the screws securing the cover to the module.

4. Replace the blown fuse.

5. Replace the protective cover and install the module in the I/O chassis.

6. Reposition the wiring arm.

7. Restart system power.

Specifications

AC (120V) Isolated Output Module

(Cat. No. 1771-OD)

Installation Data

Outputs per Module 6

Module Location 1771 I/O Chassis

Voltage Rating 92 to 138V ac @ 47-63 Hz

Output Current Rating (per channel) 2A per output (not to exceed 6A per module)

Surge Current 20A maximum for 100msec

Repeatable every 5 seconds

Minimum Load Current 60mA per output

On-state Voltage Drop 2V ac (max) at 100mA

Off-state Leakage Current 5mA (max) per output at 138V ac

Power Rating 4Watts per output

Power Dissipation 13.2 Watts (max); 1.2 Watts (min)

Thermal Dissipation 45.2 BTU/hr (max); 4.1 BTU/hr (min)

Backplane Current 225mA

Maximum Cable Length 1000 ft (304.8 m)

Isolation Voltage 1000V channel-to-channel

1500V to backplane

Environmental Conditions

Operational Temperature

Storage Temperature

Relative Humidity

0oto 60oC (32oto 140oF)

-40oto 85oC (-40oto 185oF)

5 to 95% (without condensation)

Conductors Wire Size

Category

14 gage stranded maximum

3/64 inch insulation maximum

Keying Between 4 and 6

Between 30 and 32

Fuse 5A, 3AG normal blow fuses (1 per output)

Field Wiring Arm Catalog Number 1771-WD

Wiring Arm Screw Torque 79 inchpounds

1Refer

to publication 1770-4.1, Programmable Controller Wiring and Grounding Guidelines

With offices in major cities worldwide

WORLD

HEADQUARTERS

Allen-Bradley

1201 South Second Street

Milwaukee, WI 53204 USA

Tel: (1) 414 382-2000

Telex: 43 11 016

FAX: (1) 414 382-4444

EUROPE/MIDDLE

EAST/AFRICA

HEADQUARTERS

Allen-Bradley Europe B.V.

Amsterdamseweg 15

1422 AC Uithoorn

The Netherlands

Tel: (31) 2975/43500

Telex: (844) 18042

FAX: (31) 2975/60222

ASIA/PACIFIC

HEADQUARTERS

Allen-Bradley (Hong Kong)

Limited

Room 1006, Block B, Sea

View Estate

28 Watson Road

Hong Kong

Tel: (852) 887-4788

Telex: (780) 64347

FAX: (852) 510-9436

CANADA

HEADQUARTERS

Allen-Bradley Canada

Limited

135 Dundas Street

Cambridge, Ontario N1R

5X1

Canada

Tel: (1) 519 623-1810

FAX: (1) 519 623-8930

LATIN AMERICA

HEADQUARTERS

Allen-Bradley

1201 South Second Street

Milwaukee, WI 53204 USA

Tel: (1) 414 382-2000

Telex: 43 11 016

FAX: (1) 414 382-2400

As a subsidiary of Rockwell International, one of the world’s largest technology

companies — Allen-Bradley meets today’s challenges of industrial automation with over

85 years of practical plant-floor experience. More than 11,000 employees throughout the

world design, manufacture and apply a wide range of control and automation products

and supporting services to help our customers continuously improve quality, productivity

and time to market. These products and services not only control individual machines but

integrate the manufacturing process, while providing access to vital plant floor data that

can be used to support decision-making throughout the enterprise.

Publication 1771–2.12 – April 1992

Supersedes publication 1771–2.12 – April 1990 P/N 955111–51

Otros manuales de Unidad de control de Allen-Bradley

Allen-Bradley

Allen-Bradley 1772-MJ Manual de operación

Allen-Bradley

Allen-Bradley ControlLogix DeviceNet 1756-DNB Manual de usuario

Allen-Bradley

Allen-Bradley CompactLogix EtherNet/IP 1768-EWEB Manual de usuario

Allen-Bradley

Allen-Bradley Micro800 2080-MEMBAK-RTC2 Manual de usuario

Allen-Bradley

Allen-Bradley FLEX I/O PROFIBUS 1794-APBDPV1 Manual de usuario

Allen-Bradley

Allen-Bradley ArmorBlock Series Manual

Allen-Bradley

Allen-Bradley ControlLogix DeviceNet C Series Manual de usuario

Allen-Bradley

Allen-Bradley 1756 Series Manual de usuario

Allen-Bradley

Allen-Bradley ControlLogix 1756-OA8 Manual de usuario

Allen-Bradley

Allen-Bradley 1747-ASB Manual de usuario

Allen-Bradley

Allen-Bradley PowerFlex 755 Manual de usuario

Allen-Bradley

Allen-Bradley ControlLogix 1756-OX8I Manual de usuario

Allen-Bradley

Allen-Bradley PowerFlex 755 Manual de usuario

Allen-Bradley

Allen-Bradley 1771-IL Manual de usuario

Allen-Bradley

Allen-Bradley POINT I/O 1734-VHSC5 Manual de usuario

Allen-Bradley

Allen-Bradley POINT I/O 1734-OB2 Manual de usuario

Allen-Bradley

Allen-Bradley Series B Manual de usuario

Allen-Bradley

Allen-Bradley FLEX Ex 1797-OE8 Manual de usuario

Allen-Bradley

Allen-Bradley Kinetix 5700 Manual de usuario

Allen-Bradley

Allen-Bradley CAB6-HA 2 Manual de usuario

Allen-Bradley

Allen-Bradley PowerFlex 750 Series Manual de usuario

Allen-Bradley

Allen-Bradley XM-124 Manual de usuario

Allen-Bradley

Allen-Bradley 1794-OA8K Manual de usuario

Allen-Bradley

Allen-Bradley ControlNet 1786-RPFS Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario