AJAX KeyPad Plus Manual de usuario
KeyPad Plus User Manual
Updated September 8, 2022
KeyPad Plus is a wireless touch keypad for managing the Ajax security system
with encrypted contactless cards and key fobs. Designed for indoor installation.
Supports “silent alarm” when entering the .
Manages security modes using passwords and . Indicates the
current security mode with a LED light.
The keypad only works with , and running OS Malevich 2.11
and higher. Connection to and the and integration
modules is not supported.
The keypad operates as part of the Ajax security system by connecting via the
to the hub. The communication
range without obstacles is up to 1700 meters. The pre-installed battery life is up
to 4.5 years.
duress code
cards or key fobs
Hub Plus Hub 2 Hub 2 Plus
Hub ocBridge Plus uartBridge
Jeweller secure radio communication protocol
Buy KeyPad Plus keypad
Operating principle
KeyPad Plus arms and disarms the security of the entire facility or separate
groups as well as allows activating the Night Mode. You can control the security
modes with KeyPad Plus using:
11. buttonNight mode
12. SmartBracket mounting plate (to remove the plate, slide it down)
Do not tear off the perforated part of the mount. It is required for actuating the
tamper in case of any attempt to dismantle the keypad.
13. Tamper button
14. Power button
15. Keypad QR Code
1. Codes. The keypad supports general and personal codes, as well as arming
without entering a code.
2. Cards or key fobs. You can connect and to the
system. To quickly and securely identify users, KeyPad Plus uses the
Tag key fobs Pass cards
00:00
00:04
KeyPad Plus supports code types as follows:
The number of personal codes and access codes depends on the hub model.
Before entering a code or using Tag/Pass, you should activate (“wake up”) the
KeyPad Plus by sliding your hand over the touch panel from top to bottom. When
it is activated, the button backlight is enabled, and the keypad beeps.
The KeyPad Plus is equipped with LED indicators that show the current security
mode and keypad malfunctions (if any). The security status is displayed only
when the keypad is active (the device backlight is on).
DESFire® technology. DESFire® is based on the ISO 14443 international
standard and combines 128-bit encryption and copy protection.
Keypad code — general code set up for the keypad. When used, all events
are delivered to Ajax apps on behalf of the keypad.
User code — personal code set up for a user connected to the hub. When
used, all events are delivered to Ajax apps on behalf of the user.
Keypad access code — set up for a person who is not registered in the
system. When used, events are delivered to Ajax apps with a name
associated with this code.
You can use the KeyPad Plus without ambient lighting as the keypad has a
backlight. The pressing of the buttons is accompanied by a sound signal. The
backlight brightness and keypad volume are adjustable in the settings. If you do
not touch the keypad for 4 seconds, KeyPad Plus reduces the backlight
brightness, and 8 seconds later goes into power-saving mode and turns off the
display.
If the batteries are discharged, the backlight turns on at the minimum level regardless of
the settings.
Function button
KeyPad Plus has a Function button that operates in 3 modes:
Duress code
KeyPad Plus supports duress code. It allows you to simulate alarm deactivation.
The and installed at the facility will not give you away in this
case, but the security company and other users of the security system will be
warned about the incident.
Two-stage arming
Off — the button is disabled and nothing happens after it is pressed.
Alarm — after the Function button is pressed, the system sends an alarm to
the security company monitoring station and all users.
Mute interconnected re detectors alarm — after the Function button is
pressed, the system mutes the re alarm of the FireProtect/FireProtect Plus
detectors. Available only if an is
enabled (Hub → Settings → Service → Firedetectors settings)
Interconnected Fire Detectors Alarm
Learn more
Ajax app sirens
Learn more
KeyPad Plus can participate in two-stage arming, but cannot be used as a
second-stage device. The two-stage arming process using Tag or Pass is similar
to arming using a personal or general code on the keypad.
Event transmission to the monitoring station
The Ajax security system can connect to the CMS and transmit events and
alarms to the monitoring station of the security company in SurGard (Contact
ID), ADEMCO 685, SIA (DC-09),and other proprietary protocol formats. A
complete list of supported protocols is . The device ID and the
number of the loop (zone) can be found in .
Connection
KeyPad Plus is incompatible with Hub, third-party security central units, and ocBridge
Plus and uartBridge integration modules.
Before starting connection
Only a user or PRO with full admin rights can add a device to the hub.
Learn more
available here
its states
1. Install the Ajax app and . Add a hub and create at least
one room.
create an account
2. Ensure that the hub is on and has Internet access (via Ethernet cable, Wi-Fi,
and/or mobile network). This can be done by opening the Ajax app or by
looking at the hub logo on the faceplate — it lights white or green if the hub
is connected to the network.
3. Make sure that the hub is not in armed mode and does not start updates by
checking its status in the app.
To connect KeyPad Plus
The keypad only works with one hub. When connected to a new hub, the device stops
sending commands to the old hub. Once added to a new hub, KeyPad Plus is not
removed from the device list of the old hub. This must be done manually through the
Ajax app.
KeyPad Plus turns off automatically 6 seconds after being turned on if the
keypad fails to connect to the hub. Therefore, you do not need to turn off the
device to retry the connection.
Updating the statuses of devices in the list depends on the Jeweller settings; the
default value is 36 seconds.
Icons
The icons represent some of KeyPad Plus states. You can see them in the
Devices tab in the Ajax app.
Icon Value
Jeweller signal strength — Displays the signal strength between the hub or radio signal
range extender and KeyPad Plus
Battery charge level of KeyPad Plus
1. Open the Ajax app. If your account has access to multiple hubs, select the
one to which you want to connect KeyPad Plus.
2. Go to the Devices menu and click Add Device.
3. Name the keypad, scan or enter the QR code (located on the package and
under the SmartBracket mount), and select a room.
4. Click Add; the countdown will begin.
5. Turn on the keypad by holding the power button for 3 seconds. Once
connected, KeyPad Plus will appear in the hub device list in the app. To
connect, locate the keypad at the same protected facility as the system
(within the coverage area of the hub radio network range). If the connection
fails, try again in 10 seconds.
KeyPad Plus works via a
KeyPad Plus body status notications are temporarily disabled
KeyPad Plus is temporarily deactivated
Pass/Tag reading is enabled in KeyPad Plus settings
Pass/Tag reading is disabled in KeyPad Plus settings
States
The states include information about the device and its operating parameters.
The states of KeyPad Plus can be found in the Ajax app:
Parameter Value
Malfunction
Pressing opens the KeyPad Plus
malfunctions list.
The eld is displayed only if a malfunction is
detected
Temperature
Keypad temperature. It is measured on the
processor and changes gradually.
Acceptable error between the value in the app
and the room temperature: 2–4°C
Jeweller signal strength
Jeweller signal strength between the hub /
radio signal range extender and the keypad.
Recommended values — 2-3 bars
Connection Connection status between the hub or range
radio signal range extender
Learn more
Learn more
1. Go to the Devices tab.
2. Select KeyPad Plus from the list.
extender and the keypad:
Battery charge
The battery charge level of the device. Two
states are available:
When the batteries are discharged, the Ajax
apps and the security company will receive
appropriate notications.
After sending a low battery notication, the
keypad can work for up to 2 months
Lid
The status of the device tamper, which reacts to
the detachment of or damage to the body:
Works via *range extender name*
Displays the status of the ReX range extender
use.
The eld is not displayed if the keypad works
directly with the hub
Pass/Tag Reading Displays if card and keyfob reader is enabled
Easy armed mode change/Assigned group easy
management
Displays whether or not the security mode can
be switched with Pass or Tag and without
conrmation by the control buttons , ,
Temporary Deactivation Shows the status of the device:
Online — the keypad is online
Oine — no connection to the keypad
ОК
Battery low
How battery charge is displayed in
Ajax apps
Opened
Closed
What is a tamper
No — the device operates normally and
transmits all events
Firmware KeyPad Plus rmware version
ID Device identier
Device No. Number of the device loop (zone)
Settings
KeyPad Plus is congured in the Ajax app:
To apply the settings after the change, click the Back button
Parameter Value
First eld
Device name. Displayed in the list of hub
devices, SMS text, and notications in the event
feed.
To change the device name, click on the pencil
icon .
The name can contain up to 12 Cyrillic
characters or up to 24 Latin characters
Room Selecting the virtual room to which KeyPad Plus
is assigned. The name of the room is displayed
Lid only — the hub admin has disabled
notications about the body opening
Entirely — the hub admin has entirely
excluded the keypad from the system. The
device does not execute system commands
and does not report alarms or other events
Learn more
1. Go to the Devices tab.
2. Select KeyPad Plus from the list.
3. Go to Settings by clicking on the gear icon .
Otros manuales para KeyPad Plus
1
Tabla de contenidos
Otros manuales de Teclado de AJAX
AJAX
AJAX Fibra Manual de usuario
AJAX
AJAX KeyPad Manual de usuario
AJAX
AJAX KeyPad S Plus Jeweler Manual de usuario
AJAX
AJAX KeyPad TouchScreen Manual de usuario
AJAX
AJAX KeyPad Jeweller Manual de usuario
AJAX
AJAX KeyPad Manual de usuario
AJAX
AJAX SpaceControl Manual de usuario
AJAX
AJAX KeyPad Cómo utilizar
AJAX
AJAX KeyPad Fibra Manual de usuario
AJAX
AJAX KeyPad Manual de usuario
