AJAX KeyPad Fibra Manual de usuario
KeyPad Fibra User Manual
Updated November 9, 2022
KeyPad Fibra is a wired touch keypad of the Ajax security system. Controls the
security modes and Night mode. Supports duress code and protected from
access code guessing. When it is active, the LED indication noties about the
security mode.
The keypad is compatible with and . Connection to
other , , , and is not provided.
Integration with other security systems is not provided either.
KeyPad Fibra works as part of the Ajax security system, exchanging data with
the hub using the secure Fibra wired protocol. The wired connection range is up
to 2,000 meters when using a U/UTP cat.5 twisted pair.
KeyPad Fibra is part of the wired Fibra devices line. The installation, sale, and
administration of these devices are performed only by accredited Ajax partners.
Hub Hybrid (2G) Hub Hybrid (4G)
hubs radio signal range extenders ocBridge Plus uartBridge
Buy KeyPad Fibra
Functional elements
1. Armed LED indicator.
2. Disarmed LED indicator.
3. Night mode LED indicator.
4. Malfunction LED indicator.
5. Numeric touch button box.
6. Reset button.
7. Function button.
8. Arm button.
9. Disarm button.
10. enabling button.Night mode
11. SmartBracket mounting panel. To remove the panel, slide it down.
12. Perforated part of the mounting panel. Necessary for tamper triggering in
case of any attempt to detach the keypad from the surface. Do not break it
off.
13. Perforated parts of the mounting panel for the output of cables.
14. The hole for attaching the SmartBracket mounting panel with a screw.
Operating principle
KeyPad Fibra is a touch keypad to control the Ajax security system. It controls
the security modes of the entire object or individual groups and also allows you
to enable or disable the .
You can control the security modes with KeyPad Fibra using general or personal
codes. Before entering the code, you should activate the KeyPad Fibra by
touching any part of the touch panel.
When the keypad is activated, the backlight turns on, and the built-in speaker
beeps. Backlight brightness and keypad volume are adjustable in
in Ajax apps.
If you do not touch the keypad for 4 seconds, KeyPad Fibra reduces the
brightness of the backlight, and 8 seconds later goes into power saving mode
15. . Indicates an attempt to remove the mounting panel or tear
the device off the surface.
Tamper button
16. QR code and ID (serial number) of the device. It is used to pair the device
with an Ajax security system.
17. Terminals for connecting the device to the hub.
18. Fasteners for xing cables with ties.
Night mode
keypad
settings
00:00
00:02
and turns off the display.
As the keypad goes into power saving mode, it resets the commands entered.
Access codes
KeyPad Fibra supports from 4 to 6 digit codes. Entering the code should be
conrmed by pressing one of the buttons: (Arm), (Disarm) and (Night
mode). Any characters typed accidentally are reset with a button (“Reset”).
KeyPad Fibra supports code types as follows:
The number of codes supported depends on the hub model.
KeyPad Fibra also supports arming without entering a code, if the Arming
without Codefunction is enabled in the . This function is
disabled by default.
Duress code
Keypad code — common access code. Set in the settings of each keypad.
When used, all events are delivered to Ajax apps on behalf of the keypad.
User code — the personal code of the user who has an Ajax account and is
linked to the hub. Each system user sets the code independently in the hub
settings. When used, all events are delivered to Ajax apps on behalf of the
user. The code works for all keypads that are connected to this hub.
Unregistered user code — the code of the user who does not have an Ajax
account. The code is set by an administrator or PRO with system setup
rights in the hub settings. When used, events are delivered to Ajax apps with
a name associated with this code. The code works for all keypads that are
connected to this hub.
keypad settings
A duress code allows you to simulate alarm deactivation. The and
installed at the object will not give you away in this case, and the security
company and other users of the security system will be warned about the
incident.
Features of the alarm when entering the duress code:
If the security system is disarmed with a duress code erroneously, contact the security
company monitoring station.
The keypad supports both common and personal duress codes. The common
duress code is set in the keypad settings. The personal duress code is set by the
user individually in the hub settings.
Function button
KeyPad Fibra keypad has the Function button. The button can work in one of
three modes:
Ajax apps
sirens
1. Security company monitoring station receives an alarm event Disarming
under duress. The rapid response team is going to the object.
2. All users of the security system receive a notication with no alarm about
disarming the system, and the notication is indicated by a red icon .
How to set up a duress code for registered user
How to set up a duress code for a user without an Ajax account
Alarm — the panic button mode. After pressing, the system sends an alarm
to the security company monitoring station and users and activates the
connected to the system.sirens
Mute Interconnected Fire Alarms — after the Function button is pressed, the
system disables the sirens of Ajax re detectors.
Off — the button is disabled, and after pressing the system does not execute
any commands.
Interconnected Fire Alarm muting
KeyPad Fibra can disable interconnected Fire Detectors Alarm by pressing the
Function button if congured in Mute Interconnected Fire Alarm mode. The
response of the system to pressing the button depends on the settings and the
state of the system:
The option works only if the option is
enabled in hub settings.
With the update, users can mute re detector alarms in their groups
and at the same time not affect the operation of detectors in those groups to which they
do not have access.
Unauthorized Access Auto-Lock
If a wrong code is entered three times within one minute, the keypad will be
locked for the time specied in its . During this time, the hub will ignore
all codes, while simultaneously informing the users of the security system about
an attempt to guess the code.
A user or PRO with administrator rights can unlock the keypad through the app.
Also, unlocking occurs automatically after the lock time specied in the settings
expires.
Two-stage arming
KeyPad Fibra participates in arming in two stages. This process is similar to
arming with a personal or common code on a keypad. The process should be
Interconnected Fire Alarms have propagated — the rst pressing of the
Function button mutes all re detector sirens, except for those that
registered the alarm. Pressing the button again mutes the remaining
detectors.
Interconnected Alarm Delay Time lasts — pressing the Function button
mutes the siren of the triggered Ajax re detector.
Interconnected Fire Detectors Alarm
OS Malevich 2.12
Learn more
settings
completed by re-arming with SpaceControl or restoring the terminating detector
(for example, closing the door with DoorProtect Fibra installed).
KeyPad Fibra cannot act as a terminating device in two-stage arming.
Fibra data transfer protocol
The keypad uses Fibra technology to transmit alarms and events. This is a wired
data transfer protocol that provides fast and reliable two-way communication
between the hub and the connected devices. Using the bus connection method,
Fibra delivers alarms and events instantly, even if 100 devices are connected to
the system.
Fibra supports oating key block encryption and veries each communication
session with devices to prevent sabotage and spoong. The protocol requires
regular polling of detectors by the hub with a predetermined frequency to
monitor communication and display the status of the system devices in Ajax
apps.
Learn more (in progress)
Sending events to the monitoring station
An Ajax security system can transmit alarms to the monitoring
app as well as the Central Monitoring Station (CMS) using SurGard (Contact ID),
SIA DC-09 (ADM-CID), ADEMCO 685, and other proprietary protocols. See a
complete list of supported protocols .
KeyPad Fibra can transmit the following events:
More on two-stage arming
PRO Desktop
here
Which CMSs can the Ajax security system be connected to
1. The duress code is entered.
When an alarm is received, the monitoring station operator of the security
company knows what happened and where the rapid response unit has to be
sent. All Ajax devices are addressable, so events, the device type, its assigned
name and location (room, group) can be transmitted to PRO Desktop and the
CMS. The list of transmitted parameters may differ depending on the type of the
CMS and the selected communication protocol.
The device ID, loop (zone) number, and bus number can be found in device
.
Selecting the installation site
When choosing where to place KeyPad Fibra, consider the parameters that
affect the operation of the device:
KeyPad Fibra is mounted on a at vertical surface with the bundled screws. The
keypad is intended for indoor installation only. For convenience, we recommend
installing the keypad at a height of 1.3–1.5 meters from the oor.
Consider the placement recommendations when designing the security system
project for your object. The security system should be designed and installed by
professionals. The list of authorized Ajax partners is .
2. The panic button is pressed (if the Function button works in the panic
button mode).
3. The keypad is locked due to an attempt to guess a code.
4. Tamper alarm/recovery.
5. Loss/recovery of connection between KeyPad Fibra and the hub.
6. Temporary activation/deactivation of KeyPad Fibra.
7. Unsuccessful attempt to arm the security system (with the
enabled).
system integrity
check
states in the
Ajax app
Fibra Signal Strength.
Cable length for connecting KeyPad Fibra.
available here
Do not install KeyPad Fibra
Fibra Signal Strength
The Fibra signal level is determined by the number of undelivered or corrupted
data packages over a certain period. The icon in the Devices tab in Ajax
apps indicates the signal strength:
The following factors affect the signal strength:
Design
To correctly install and congure security system devices, it is important to
properly design the security system. The design must consider the number and
types of devices at the object, their exact location and installation height, the
Outdoors. This could damage the keypad.
Inside premises with temperature and humidity outside the permissible
limits. This could damage the keypad.
In places where the keypad has an unstable or low signal strength. This can
lead to a loss of connection between the hub and the keypad.
Where articles of clothing, power cables, or an Ethernet cable could be an
obstacle to the keypad. This can lead to false clicks on the touch panel of
the device.
Three bars — excellent signal strength.
Two bars — good signal strength.
One bar — low signal strength, stable operation is not guaranteed.
Crossed out icon — no signal, stable operation is not guaranteed.
The number of detectors connected to one Fibra line.
Cable length and type.
The correctness of wire connections to the terminals.
length of wired Fibra lines, the type of cable used, and other parameters. Tips for
designing Fibra wired systems are available .
Topologies
Currently, Ajax security systems support two topologies: Beam (Radial wiring)
and Ring.
Connecting devices using a Ring topology will be implemented in the next OS Malevich
updates. Hardware update of Hub Hybrid is not required.
Beam connection method (Radial wiring) occupies one bus output of the hub.
Only the segment that remains physically connected to the hub will function in
the event of a line break. All devices connected after the breakpoint will lose
connection with the hub.
Ring connection method occupies two bus outputs of the hub. If the ring breaks
in one place, no device will be disabled. The ring recongures into two lines,
which continue to operate normally. Users and the security company will receive
notication about the break.
Beam (Radial wiring) Ring
in this article
Tabla de contenidos
Otros manuales de Teclado de AJAX
AJAX
AJAX SpaceControl Manual de usuario
AJAX
AJAX KeyPad Combi Manual de usuario
AJAX
AJAX Fibra Manual de usuario
AJAX
AJAX KeyPad Jeweller Manual de usuario
AJAX
AJAX KeyPad Manual de usuario
AJAX
AJAX KeyPad Manual de usuario
AJAX
AJAX KeyPad TouchScreen Manual de usuario
AJAX
AJAX KeyPad S Plus Jeweler Manual de usuario
AJAX
AJAX KeyPad Cómo utilizar
AJAX
AJAX KeyPad Manual de usuario
