Agilent Technologies 8960 Manual de instrucciones

Agilent Technologies 8960 Series 10 E5515B,C,T Wireless Communications Test Set

Manual Operation: Getting Started Guide

AMPS/136 Mobile Test Application E1961A Revision: A.04

cdma2000/IS-2000 Mobile Test Application E1962A Revision A.01, E1962B Revision: B.01

GPRS Mobile Test Application E1964A Revision: A.01

GSM Mobile Test Application E1960A Revision: A.07

GSM_AMPS/136 Fast Switch Mobile Test Application E1985A Revision: A.01

Agilent Part No: 5967-5124

Print Date: March 2001

http://www.agilent.com/find/8960support

深圳德标仪器 135-1095-0799

Edition/Print Date

All Editions and Updates of this manual and their creation dates are listed below.

March 2001 - 5967-5124

Safety Summary

The following general safety precautions must be observed during all phases of operation of

this instrument. Failure to comply with these precautions or with specific warnings elsewhere

in this manual violates safety standards of design, manufacture, and intended use of the

instrument. Agilent Technologies Inc. assumes no liability for the customer’s failure to comply

with these requirements.

GENERAL

This product is a Safety Class 1 instrument (provided with a protective earth terminal). The

protective features of this product may be impaired if it is used in a manner not specified in

the operation instructions.

All Light Emitting Diodes (LEDs) used in this product are Class 1 LEDs as per IEC 60825-1.

This product has been designed and tested in accordance with IEC Publication 1010, "Safety

Requirements for Electronic Measuring Apparatus," and has been supplied in a safe

condition. This instruction documentation contains information and warnings which must be

followed by the user to ensure safe operation and to maintain the product in a safe condition.

深圳德标仪器 135-1095-0799

ENVIRONMENTAL CONDITIONS

This instrument is intended for indoor use in an installation category II, pollution degree 2

environment. It is designed to operate at a maximum relative humidity of 95% and at

altitudes of up to 2000 meters. Refer to the specifications tables for the ac mains voltage

requirements and ambient operating temperature range.

Ventilation Requirements: When installing the product in a cabinet, the convection into and

out of the product must not be restricted. The ambient temperature (outside the cabinet) must

be less than the maximum operating temperature of the product by 4°C for every 100 watts

dissipated in the cabinet. If the total power dissipated in the cabinet is greater than 800

watts, then forced convection must be used.

BEFORE APPLYING POWER

Verify that the product is set to match the available line voltage, the correct fuse is installed,

and all safety precautions are taken. Note the instrument's external markings described

under Safety Symbols.

GROUND THE INSTRUMENT

To minimize shock hazard, the instrument chassis and cover must be connected to an

electrical protective earth ground. The instrument must be connected to the ac power mains

through a grounded power cable, with the ground wire firmly connected to an electrical

ground (safety ground) at the power outlet. Any interruption of the protective (grounding)

conductor or disconnection of the protective earth terminal will cause a potential shock

hazard that could result in personal injury.

FUSES

Only fuses with the required rated current, voltage, and specified type (normal blow, time

delay, etc.) should be used. Do not use repaired fuses or short-circuited fuse holders. To do so

could cause a shock or fire hazard.

DO NOT OPERATE IN AN EXPLOSIVE ATMOSPHERE

Do not operate the instrument in the presence of flammable gases or fumes.

DO NOT REMOVE THE INSTRUMENT COVER

Operating personnel must not remove instrument covers. Component replacement and

internal adjustments must be made only by qualified service personnel.

Instruments that appear damaged or defective should be made inoperative and secured

against unintended operation until they can be repaired by qualified service personnel.

深圳德标仪器 135-1095-0799

WARNING The WARNING sign denotes a hazard. It calls attention to a

procedure, practice, or the like, which, if not correctly

performed or adhered to, could result in personal injury. Do not

proceed beyond a WARNING sign until the indicated conditions

are fully understood and met.

CAUTION The CAUTION sign denotes a hazard. It calls attention to an operating

procedure, or the like, which, if not correctly performed or adhered to,

could result in damage to or destruction of part or all of the product. Do

not proceed beyond a CAUTION sign until the indicated conditions are

fully understood and met.

Safety Symbols

Caution, refer to accompanying documents

Warning, risk of electric shock

Earth (ground) terminal

Alternating current

Frame or chassis terminal

Standby (supply). Units with this symbol are not completely disconnected from ac

mains when this switch is off.

To completely disconnect the unit from ac mains, either disconnect the power cord, or have a

qualified electrician install an external switch.

深圳德标仪器 135-1095-0799

Product Markings

CE - the CE mark is a registered trademark of the European Community. A CE mark

accompanied by a year indicated the year the design was proven.

CSA - the CSA mark is a registered trademark of the Canadian Standards Association.

CERTIFICATION

Agilent Technologies certifies that this product met its published specifications at the time of

shipment from the factory. Agilent Technologies further certifies that its calibration

measurements are traceable to the United States National Institute of Standards and

Technology, to the extent allowed by the Institute’s calibration facility, and to the calibration

facilities of other International Standards Organization members

深圳德标仪器 135-1095-0799

Agilent Technologies Warranty Statement for

Commercial Products

Agilent Technologies 8960 Series 10 E5515B,C,T Wireless Communications Test Set,

AMPS/136 Mobile Test Application E1961A

cdma2000 Mobile Test Application E1962B

GPRS Mobile Test Application E1964A

GSM Mobile Test Application E1960A

IS-2000 Mobile Test Application E1962A

Duration of Warranty: 1 year

1. Agilent Technologies warrants Agilent Technologies hardware, accessories and supplies

against defects in materials and workmanship for the period specified above. If Agilent

Technologies receives notice of such defects during the warranty period, Agilent

Technologies will, at its option, either repair or replace products which prove to be

defective. Replacement products may be either new or like-new.

2. Agilent Technologies warrants that Agilent Technologies software will not fail to execute

its programming instructions, for the period specified above, due to defects in material and

workmanship when properly installed and used. If Agilent Technologies receives notice of

such defects during the warranty period, Agilent Technologies will replace software media

which does not execute its programming instructions due to such defects.

3. Agilent Technologies does not warrant that the operation of Agilent Technologies products

will be uninterrupted or error free. If Agilent Technologies is unable, within a reasonable

time, to repair or replace any product to a condition as warranted, customer will be

entitled to a refund of the purchase price upon prompt return of the product.

4. Agilent Technologies products may contain remanufactured parts equivalent to new in

performance or may have been subject to incidental use.

5. The warranty period begins on the date of delivery or on the date of installation if installed

by Agilent Technologies. If customer schedules or delays Agilent Technologies installation

more than 30 days after delivery, warranty begins on the 31st day from delivery.

深圳德标仪器 135-1095-0799

6. Warranty does not apply to defects resulting from (a) improper or inadequate maintenance

or calibration, (b) software, interfacing, parts or supplies not supplied by Agilent

Technologies, (c) unauthorized modification or misuse, (d) operation outside of the

published environmental specifications for the product, or (e) improper site preparation or

maintenance.

7. TO THE EXTENT ALLOWED BY LOCAL LAW, THE ABOVE WARRANTIES ARE

EXCLUSIVE AND NO OTHER WARRANTY OR CONDITION, WHETHER WRITTEN

OR ORAL IS EXPRESSED OR IMPLIED AND AGILENT TECHNOLOGIES

SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTIES OR CONDITIONS OR

MERCHANTABILITY, SATISFACTORY QUALITY, AND FITNESS FOR A

PARTICULAR PURPOSE.

8. Agilent Technologies will be liable for damage to tangible property per incident up to the

greater of $300,000 or the actual amount paid for the product that is the subject of the

claim, and for damages for bodily injury or death, to the extent that all such damages are

determined by a court of competent jurisdiction to have been directly caused by a defective

Agilent Technologies product.

9. TO THE EXTENT ALLOWED BY LOCAL LAW, THE REMEDIES IN THIS WARRANTY

STATEMENT ARE CUSTOMER’S SOLE AND EXCLUSIVE REMEDIES. EXCEPT AS

INDICATED ABOVE, IN NO EVENT WILL AGILENT TECHNOLOGIES OR ITS

SUPPLIERS BE LIABLE FOR LOSS OF DATA OR FOR DIRECT, SPECIAL,

INCIDENTAL, CONSEQUENTIAL (INCLUDING LOST PROFIT OR DATA), OR OTHER

DAMAGE, WHETHER BASED IN CONTRACT, TORT, OR OTHERWISE.

FOR CONSUMER TRANSACTIONS IN AUSTRALIA AND NEW ZEALAND: THE

WARRANTY TERMS CONTAINED IN THIS STATEMENT, EXCEPT TO THE EXTENT

LAWFULLY PERMITTED, DO NOT EXCLUDE RESTRICT OR MODIFY AND ARE IN

ADDITION TO THE MANDATORY STATUTORY RIGHTS APPLICABLE TO THE SALE

OF THIS PRODUCT TO YOU.

ASSISTANCE

Product maintenance agreements and other customer assistance agreements are available for

Agilent Technologies products. For any assistance, contact your nearest Agilent Technologies

Sales and Service Office.

深圳德标仪器 135-1095-0799

Service and Support

Any adjustment, maintenance, or repair of this product must be performed by qualified

personnel. Contact your customer engineer through your local Agilent Technologies Service

Center. You can find a list of local service representatives on the Web at:

http://www.agilent-tech.com/services/English/index.html

If you do not have access to the Internet, one of these centers can direct you to your nearest

representative:

United States Test and Measurement Call Center

(Toll free in US)

(800) 452-4844

Europe

(31 20) 547 9900

Canada

(905) 206-4725

Japan Measurement Assistance Center

(81) 426 56 7832

(81) 426 56 7840 (FAX)

Latin America

(305) 267 4288 (FAX)

Australia/New Zealand

1 800 629 485 (Australia)

0800 738 378 (New Zealand)

Asia-Pacific

(852) 2599 7777

(852) 2506 9285 (FAX)

深圳德标仪器 135-1095-0799

Regional Sales Offices

United States of America:

Agilent Technologies (tel) 1 800 452 4844

Test and Measurement Call Center

P.O. Box 4026

Englewood, CO 80155-4026

Canada:

Agilent Technologies Canada Inc. (tel) 1 877 894 4414

2660 Matheson Blvd. E

Mississauga, Ontario

L4W 5G1

Europe:

Agilent Technologies (tel) (3120) 547 9999

European Marketing Organization

P.O. Box 999

1180 AZ Amstelveen

The Netherlands

Japan:

Agilent Technologies Japan Ltd. (tel) (81) 456-56-7832

Measurement Assistance Center (fax) (81) 426-56-7840

9-1 Takakura-Cho, Hachioji-Shi,

Tokyo 192-8510, Japan

Latin America:

Agilent Technologies (tel) (305) 267 4245

Latin America Region Headquarters (fax) (305) 267 4286

5200 Blue Lagoon Drive,

Suite #950

Miami, Florida 33126

U.S. A.

深圳德标仪器 135-1095-0799

Australia/New Zealand:

Agilent Technologies Australia Pty Ltd. Australia New Zealand

347 Burwood Highway (tel) 1 800 629 485 (tel) 0 800 738 378

Forest Hill, Victoria 3131 (fax) (61 3) 9272 0749 (fax) (64 4) 802

6881

Asia Pacific:

Agilent Technologies (tel) (852) 3197 7777

24/F, Cityplaza One, (fax) (852) 2506 9233

111 Kings Road,

Taikoo Shing, Hong Kong

深圳德标仪器 135-1095-0799

Otros manuales para 8960

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Equipo de prueba de Agilent Technologies

Agilent Technologies

Agilent Technologies Ininiium 9000 Manual de usuario

Agilent Technologies

Agilent Technologies aurora Duet Manual de usuario

Agilent Technologies

Agilent Technologies 54621A Manual

Agilent Technologies

Agilent Technologies E7495A RF Manual de instrucciones

Agilent Technologies

Agilent Technologies 1000A Series Manual de usuario

Agilent Technologies

Agilent Technologies InfiniiVision 7000 Series Manual de usuario

Agilent Technologies

Agilent Technologies E1852B Manual de usuario

Agilent Technologies

Agilent Technologies 16043A Manual de operación

Agilent Technologies

Agilent Technologies Infiniium 90000 A Manual de usuario

Agilent Technologies

Agilent Technologies 5DX II Series Manual de usuario

Agilent Technologies

Agilent Technologies InfiniiVision 2000 X-Series Manual de usuario

Agilent Technologies

Agilent Technologies U1610/20A Manual de usuario

Agilent Technologies

Agilent Technologies InfiniiVision 3000 X- Series Manual del operador

Agilent Technologies

Agilent Technologies E7490A Manual de usuario

Agilent Technologies

Agilent Technologies InfiniiVision 3000 X-Series Manual

Agilent Technologies

Agilent Technologies 16452A Manual de operación

Agilent Technologies

Agilent Technologies Infiniium 90000 Q-Series Manual de usuario

Agilent Technologies

Agilent Technologies AuroraPresto Manual de usuario

Agilent Technologies

Agilent Technologies U1602B Manual de usuario

Agilent Technologies

Agilent Technologies InfiniiVision 6000 Series Manual de usuario

Agilent Technologies

Agilent Technologies 90000 X Series Manual de usuario

Agilent Technologies

Agilent Technologies InfiniiVision 2000 X-Series Manual

Agilent Technologies

Agilent Technologies 5530 Manual de usuario

Agilent Technologies

Agilent Technologies InfiniiVision 5000 Series Manual

Manuales populares de Equipo de prueba de otras marcas

SMART

SMART KANAAD SBT XTREME 3G Series Manual de usuario

Vernier

Vernier Go Direct Voltage Manual de usuario

Lifeloc

Lifeloc R.A.D.A.R. Manual de usuario

Fluke

Fluke T5-600 Instrucciones de funcionamiento e instalación

Mercury

Mercury TSL01 Manual de usuario

MAHA

MAHA MBT Series Manual de usuario

Fuji Electric

Fuji Electric P-61 Manual de usuario

ETC

ETC SealerAtor Manual de usuario

Skyfine

Skyfine ETHYWAY V2 Manual de usuario

Appion

Appion G5 Twin Manual de usuario

PCB Piezotronics

PCB Piezotronics 8159-0112A Manual de usuario

BW Technologies

BW Technologies MicroDock II Manual de usuario

Sun Nuclear

Sun Nuclear 1027 Manual de usuario

Biomark

Biomark HPR LITE READER Manual de usuario

Hioki

Hioki 3169-20 Manual de usuario

Ashcroft

Ashcroft ATE-100 Manual de usuario

Rohde & Schwarz

Rohde & Schwarz RTA4000 Manual de usuario

Ritmix

Ritmix RAT-701 Manual de usuario