Agilent Technologies U1253B Manual

Agilent Technologies

Agilent U1253B True

RMS OLED Multimeter

User’s and Service Guide

II U1253B User’s and Service Guide

Notices

® Agilent Technologies, Inc. , 2009-2010

No part of this manual may be reproduced in

any form or by any means (including elec-

tronic storage and retrieval or translation

into a foreign language) without prior agree-

ment and written consent from Agilent

Technologies, Inc. as governed by United

States and international copyright laws.

Manual Part Number

U1253-90035

Edition

Fourth Edition, November 8, 2010

Agilent Technologies, Inc.

5301 Stevens Creek Blvd.

Santa Clara, CA 95051 USA

Trademark Acknowledgements

Pentium is a U.S. registered trademark of

Intel Corporation.

Microsoft, Visual Studio, Windows, and MS

Windows are trademarks of Microsoft Cor-

poration in the United States and/or other

countries.

Accessories Warranty

Agilent offers warranty for product’s acces-

sories for up to 3 months from the end-user

acceptance date.

Standard Calibration Service

(optional)

Agilent offers an optional calibration service

contract for a period of 3 years from

end-user acceptance date.

Warranty

The material contained in this docu-

ment is provided “as is,” and is sub-

ject to being changed, without notice,

in future editions. Further, to the max-

imum extent permitted by applicable

law, Agilent disclaims all warranties,

either express or implied, with regard

to this manual and any information

contained herein, including but not

limited to the implied warranties of

merchantability and fitness for a par-

ticular purpose. Agilent shall not be

liable for errors or for incidental or

consequential damages in connec-

tion with the furnishing, use, or per-

formance of this document or of any

information contained herein. Should

Agilent and the user have a separate

written agreement with warranty

terms covering the material in this

document that conflict with these

terms, the warranty terms in the sep-

arate agreement shall control.

Technology Licenses

The hardware and/or software described in

this document are furnished under a license

and may be used or copied only in accor-

dance with the terms of such license.

Restricted Rights Legend

U.S. Government Restricted Rights. Soft-

ware and technical data rights granted to

the federal government include only those

rights customarily provided to end user cus-

tomers. Agilent provides this customary

commercial license in Software and techni-

cal data pursuant to FAR 12.211 (Technical

Data) and 12.212 (Computer Software) and,

for the Department of Defense, DFARS

252.227-7015 (Technical Data - Commercial

Items) and DFARS 227.7202-3 (Rights in

Commercial Computer Software or Com-

puter Software Documentation).

Safety Notices

CAUTION

A CAUTION notice denotes a haz-

ard. It calls attention to an operat-

ing procedure, practice, or the like

that, if not correctly performed or

adhered to, could result in damage

to the product or loss of important

data. Do not proceed beyond a

CAUTION notice until the indicated

conditions are fully understood and

met.

WARNING

A WARNING notice denotes a

hazard. It calls attention to an

operating procedure, practice, or

the like that, if not correctly per-

formed or adhered to, could result

in personal injury or death. Do not

proceed beyond a WARNING

notice until the indicated condi-

tions are fully understood and

met.

U1253B User’s and Service Guide III

Safety Symbols

The following symbols on the instrument and in the documentation

indicate precautions which must be taken to maintain safe operation of

the instrument.

Direct current (DC) Off (supply)

Alternating current (AC) On (supply)

Both direct and alternating current Caution, risk of electric shock

Three-phase alternating current Caution, risk of danger (refer to this manual

for specific Warning or Caution information)

Earth (ground) terminal Caution, hot surface

Protective conductor terminal Out position of a bi-stable push control

Frame or chassis terminal In position of a bi-stable push control

Equipotentiality Category III 1000 V overvoltage protection

Equipment protected throughout by

double insulation or reinforced

insulation

Category IV 600 V overvoltage protection

CAT III

1000 V

CAT IV

600 V

IV U1253B User’s and Service Guide

General Safety Information

The following general safety precautions must be observed during all

phases of operation, service, and repair of this instrument. Failure to

comply with these precautions or with specific warnings elsewhere in this

manual violates safety standards of design, manufacture, and intended

use of the instrument. Agilent Technologies assumes no liability for the

customer’s failure to comply with these requirements.

U1253B User’s and Service Guide V

WARNING

• When working above 60 V DC, 30 V AC rms, or 42.4 V AC peak, exercise caution – such

range poses a shock hazard.

• Do not measure more than the rated voltage (as marked on the multimeter) between

terminals, or between terminal and earth ground.

• Double-check the meters operation by measuring a known voltage.

•Forcurrentmeasurement, turn off circuit power before connecting the multimeter to

the circuit. Always place the multimeter in series with the circuit.

• When connecting probes, always connect the common test probe first. When

disconnecting probes, always disconnect the live test probe first.

• Detach test probes from the multimeter before you open the battery cover.

• Do not use the multimeter with the battery cover or part of the cover removed or loose.

• Replace the battery as soon as the low battery indicator flashes on screen. This is to

avoid false readings, which may lead to possible electric shock or personal injury.

• Do not operate the product in an explosive atmosphere or in the presence of

flammable gases or fumes.

• Inspect the case for cracks or missing plastic. Pay extra attention to the insulation

surrounding the connectors. Do not use the multimeter if it is damaged.

• Inspect the test probes for damaged insulation or exposed metal, and check for

continuity. Do not use the test probe if it is damaged.

• Do not use any other AC charger adapter apart from the one certified by Agilent with

this product.

• Do not use repaired fuses or short-circuited fuse-holders. For continued protection

against fire, replace the line fuses only with fuses of the same voltage and current

rating and recommended type.

• Do not service or perform adjustments alone. Under certain condition, hazardous

voltages may exist, even with the equipment switched off. To avoid dangerous electric

shock, service personnel must not attempt internal service or adjustment unless

another person, capable of rendering resuscitation or first aid, is present.

• Do not substitute parts or modify equipment to avoid the danger of introducing

additional hazards. Return the product to the nearest Agilent Technologies Sales and

Service office for service and repair to ensure the safety features are maintained.

• Do not operate damaged equipment as the safety protection features built into this

product may have been impaired, either through physical damage, excessive

moisture, or any other reason. Remove power and do not use the product until safe

operation can be verified by service-trained personnel. If necessary, return the

product to the nearest Agilent Technologies Sales and Service office for service and

repair to ensure the safety features are maintained.

VI U1253B User’s and Service Guide

CAUTION

•Turn off circuit power and discharge all high-voltage capacitors in the circuit before you

perform resistance and capacitance measurements or continuity and diodes tests.

•Use the correct terminals, function, and range for your measurements.

•Never measure voltage when current measurement is selected.

•Use only the recommended rechargeable battery. Ensure proper insertion of battery in

the multimeter, and follow the correct polarity.

•Disconnect test leads from all the terminals during battery charging.

U1253B User’s and Service Guide VII

Environmental Conditions

This instrument is designed for indoor use and in areas with low

condensation. The table below shows the general environmental

requirements for this instrument.

Environmental conditions Requirements

Operating temperature Full accuracy from –20 °C to 55 °C

Operating humidity Full accuracy up to 80% R.H. (relative

humidity) for temperature up to 35 °C,

decreasing linearly to 50% R.H. at 55 °C

Storage temperature –40 °C to 70 °C (with battery removed)

Altitude Up to 2000 m

Pollution degree Pollution Degree 2

CAUTION

The U1253B True RMS OLED Multimeter complies with the following

safety and EMC requirements.

•IEC 61010-1:2001/EN61010-1:2001 (2nd Edition)

•Canada: CAN/CSA-C22.2 No. 61010-1-04

•USA: ANSI/UL 61010-1:2004

•IEC61326-1:2005 / EN61326-1:2006

•Canada: ICES/NMB-001:2004

•Australia/New Zealand: AS/NZS CISPR11:2004

VIII U1253B User’s and Service Guide

Regulatory Markings

The CE mark is a registered trademark

of the European Community. This CE

mark shows that the product complies

with all the relevant European Legal

Directives.

The C-tick mark is a registered

trademark of the Spectrum

Management Agency of Australia. This

signifies compliance with

the Australia EMC Framework

regulations under the terms of the

Radio Communication Act of 1992.

ICES/NMB-001 indicates that this ISM

device complies with the Canadian

ICES-001.

Cet appareil ISM est confomre a la

norme NMB-001 du Canada.

This instrument complies with the

WEEE Directive (2002/96/EC) marking

requirement. This affixed product label

indicates that you must not discard

this electrical/electronic product in

domestic household waste.

The CSA mark is a registered

trademark of the Canadian Standards

Association.

U1253B User’s and Service Guide IX

Waste Electrical and Electronic Equipment (WEEE) Directive

2002/96/EC

This instrument complies with the WEEE Directive (2002/96/EC) marking

requirement. This affixed product label indicates that you must not discard

this electrical/electronic product in domestic household waste.

Product Category:

With reference to the equipment types in the WEEE directive Annex 1, this

instrument is classified as a “Monitoring and Control Instrument” product.

The affixed product label is as shown below.

Do not dispose in domestic household waste

To return this unwanted instrument, contact your nearest Agilent

Technologies, or visit:

www.agilent.com/environment/product

for more information.

Agilent Technologies, through Rechargeable Battery Recycling Corporation (RBRC), offers free and convenient

battery recycling options in the U.S. and Canada. Contact RBRC at 877-2-RECYCLE (877.273.2925) or online at:

http://www.call2recycle.org/ for the nearest recycling location.

X U1253B User’s and Service Guide

In This Guide…

1 Getting Started Tutorial

This chapter contains a brief description of the U1253B true RMS OLED

multimeter front panel, rotary switch, keypad, display, terminals, and rear

panel.

2 Making Measurements

This chapter contains detailed information on how to take measurements

using the U1253B true RMS OLED multimeter.

3 Functions and Features

This chapter contains detailed information on functions and features

available in the U1253B true RMS OLED multimeter.

4 Changing the Default Settings

This chapter describes how to change the default factory settings of the

U1253B true RMS OLED multimeter and other available setting options.

5 Maintenance

This chapter will help you troubleshoot a malfunctioning U1253B true

RMS OLED multimeter.

6 Performance Tests and Calibration

This chapter contains the performance test procedures and adjustment

procedures. The performance test procedures allow you to verify that the

U1253B true RMS OLED multimeter is operating within its published

specifications. If these performance tests reveal any measurement

function to be out of specification, you may calibrate the said function by

following the relevant adjustment procedures.

7 Specifications

This chapter details the specifications of the U1253B true RMS OLED

multimeter.

Otros manuales para U1253B

Tabla de contenidos

Otros manuales de Multímetro de Agilent Technologies

Agilent Technologies

Agilent Technologies Agilent 8163A Manual de usuario

Agilent Technologies

Agilent Technologies U1241B Manual de usuario

Agilent Technologies

Agilent Technologies 3458A Guía de inicio rápido

Agilent Technologies

Agilent Technologies 34410A Manual de usuario

Agilent Technologies

Agilent Technologies 34401A Manual de usuario

Agilent Technologies

Agilent Technologies 34450A 5 Digit Multimeter Manual de usuario

Agilent Technologies

Agilent Technologies U3402A Manual de usuario

Agilent Technologies

Agilent Technologies U1241A Manual de usuario

Agilent Technologies

Agilent Technologies U1253B Manual de usuario

Agilent Technologies

Agilent Technologies U1231A Manual de usuario

Agilent Technologies

Agilent Technologies 34450A Manual de usuario

Agilent Technologies

Agilent Technologies 3458A Manual de usuario

Agilent Technologies

Agilent Technologies U1251A Manual

Agilent Technologies

Agilent Technologies U1251A Manual de usuario

Agilent Technologies

Agilent Technologies 34401A Manual de usuario

Agilent Technologies

Agilent Technologies U3401A Manual de usuario

Agilent Technologies

Agilent Technologies U1272A Manual de usuario

Agilent Technologies

Agilent Technologies U1251B Manual

Agilent Technologies

Agilent Technologies U1241B Manual de usuario

Agilent Technologies

Agilent Technologies 34450A Manual de usuario

Agilent Technologies

Agilent Technologies 3457A Manual de usuario

Agilent Technologies

Agilent Technologies 34401A Manual de usuario

Agilent Technologies

Agilent Technologies E5071C Manual de instalación y funcionamiento

Agilent Technologies

Agilent Technologies U1273A Manual de usuario

Manuales populares de Multímetro de otras marcas

Fluke

Fluke 83 Manual de usuario

Hameg

Hameg HM 8012 Manual de usuario

Mastech

Mastech MY70 Manual de usuario

Steren

Steren MUL-300 Manual de usuario

Somogyi Elektronic

Somogyi Elektronic home SMA 92 Manual de usuario

Gossen MetraWatt

Gossen MetraWatt METRAmax 6 Manual de usuario

PeakTech

PeakTech 4000 Manual de uso y cuidado

YOKOGAWA

YOKOGAWA 90050B Manual de usuario

Gossen MetraWatt

Gossen MetraWatt METRALINE DMM16 Manual de usuario

Fluke

Fluke 8846A Manual de operación y mantenimiento

Tempo Communications

Tempo Communications MM200 Manual de usuario

Elenco Electronics

Elenco Electronics CM-1555 Manual de usuario

Mastech

Mastech MS8238C Manual de usuario

SDAR

SDAR 830A, 830B, 830D, 830C Manual de usuario

RS PRO

RS PRO RS-9519BT Manual de usuario

BGS technic

BGS technic 8890 Manual de usuario

Amprobe

Amprobe Hexagon 60 Manual de usuario

Morris

Morris 57074 Manual de usuario