Agilent Technologies ESA-E E4407B Manual de instalación y operación

Installation Note

Part Number E4407-90041 Supersedes: E4407-90032

Printed in USA July 2005

Agilent Technologies

E4407B, E4408B Spectrum Analyzers and

E7405A EMC Analyzers

APC 3.5 mm Input Connector (Option BAB)

Retrofit Kit

Notice.

The information contained in this document is subject to change without notice.

Agilent Technologies makes no warranty of any kind with regard to this material, including but not limited to, the

implied warranties of merchantability and fitness for a particular purpose. Agilent Technologies shall not be liable

for errors contained herein or for incidental or consequential damages in connection with the furnishing,

performance, or use of this material.

Installation Note E4407-90041 3

Introduction

This procedure can be used to retrofit the APC 3.5 mm input connector (Option BAB) in E4407B, E4408B spectrum

analyzers, or E7405A EMC analyzers. One kit is provided for all model numbers.

To ensure that this newly installed option is functioning properly, the procedure that follows includes the requirement of

performing certain adjustments and performance verification tests. However, the completion of these tests does not guarantee

that the instrument meets all advertised specifications.

Software is required to perform the required adjustments, and can be used to automate the performance verification testing.

Information on how to obtain this software can be found at:

www.agilent.com/find/calibrationsoftware

While Agilent does recommend that a full calibration be performed after the installation of this upgrade, the end user must

ultimately determine whether they want this service or not. If a full calibration is required, arrangements regarding the level of

calibration must be made between the end user and the calibration provider.

Products Affected: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E4407B Spectrum Analyzer

E4408B Spectrum Analyzer

E7405A EMC Analyzer

Serial Numbers: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Any

Option: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BAB

To Be Performed By: . . . . . . . . . . . . . . . . . . . . . . . . . . . . (X) Agilent Technologies Service Center

(X) Personnel Qualified by Agilent

()Customer

Estimated Installation Time:. . . . . . . . . . . . . . . . . . . . . . . 2.0 Hours

Estimated Verification Time: . . . . . . . . . . . . . . . . . . . . . . 3.0 Hours

Additional Recommended Task: . . . . . . . . . . . . . . . Agilent recommends a full calibration be performed to verify

instrument specifications

Installation Note E4407-90041

Installation Kit Parts List

Tools Required

• T-10 TORX screwdriver

• T-15 TORX screwdriver

• Function generator

• Synthesized sweeper

• Digital voltmeter

• Power meter, dual channel

• RF Power sensor (2 required)

• Microwave power sensor

• 50 Ohm termination

• Power splitter

• 20 dB Attenuator (Option 1DS only)

• APC 3.5 (m) Cable

• APC 3.5 (m) to Type-N (m) Adapter

• APC 3.5 (m) to Type-N (f) Adapter

• BNC Tee (f,m,f)

• Dual banana to BNC (f) Adapter

Quantity Description Item Number

1 APC 3.5 connector assembly (A8J1) E4407-60002

1 Cable assembly, RF IN/ATTN (W6) E4404-20017

1 Adapter, APC 3.5 (f) to APC 3.5 (f) 5061-5311

1 Adapter, BNC (f) to SMA (m) 1250-1200

1Option Upgrade Entitlement Certificate ---

1 APC 3.5 connector installation note E4407-90001

Installation Note E4407-90041 5

Torque Settings

To avoid potential RFI leakage and prevent connector damage, tighten to the following torque limits:

WARNING Before you disassemble the instrument, turn the power switch to Standby and unplug the instrument.

Failure to unplug the instrument can result in personal injury.

CAUTION Electrostatic discharge (ESD) can damage or destroy electronic components. All work on electronic

assemblies should be performed at a static-safe workstation. Refer to the documentation that pertains to your

instrument for information about static-safe workstations and ordering static-safe accessories.

Item Torque

In-lb N-cm

SMA Connectors 8.5 95

3-mm, T-10 TORX screws 9102

4-mm, T-15 TORX screws 21 236

Installation Note E4407-90041

Procedure

Removing the Dress Cover

1. Referring to Figure 1, disconnect the analyzer from ac power (1).

2. Remove any adapters or cables connected to the front panel (2).

3. Position the handle (4) to the rear of the analyzer.

4. Carefully place the analyzer on the work surface with the front frame (3) facing down.

5. Remove the four screws (5) that hold the rear frame (6) and dress cover (7) in place.

6. Remove the rear frame (6) and dress cover (7) by sliding them towards the rear of the analyzer.

Figure 1 Dress Cover and Rear Frame Removal and Installation

Installation Note E4407-90041 7

Extending the Front Frame

The front frame assembly can be extended from the instrument without detaching any connections or removing the chassis

cover.

1. Referring to Figure 2, with the instrument still on its face, remove the five screws (1), two on the bottom side and three on

the top of the instrument, that secure the front frame to the RF assembly and chassis cover.

2. Place the instrument with the top side facing up and remove the remaining two screws (2) that secure the front frame

subpanel to the chassis.

3. Slide the front frame forward until it catches on the tabs on the sides of the chassis.

Removing the Front Frame

Figure 2 Front Frame Assembly Removal

1. Disconnect the ribbon cable (3) from the front panel interface board.

2. Carefully pull the sides of the front frame subpanel away from the chassis and over the tabs on the chassis.

3. Slide the front frame forward to disengage from the chassis assembly.

Installation Note E4407-90041

Removing and Replacing the RF Input connector

1. Rotate the analyzer so the right side is resting on the table.

2. Referring to Figure 3, locate W6 (1). W6 is a semi-rigid coax cable connected between the A8A5 input attenuator (2)

and the A8J1 input connector (3).

Figure 3 Replacing the Input Connector and Cable

3. Remove W6 (1) from A8J1 (3), then from A8A5 (2). Discard the removed cable as it will no longer be needed.

4. Remove the A8J1 input connector from the midweb (4).

5. Attach the APC 3.5 mm input connector included in this kit to the midweb (4) using the two 3.0 mm screws provided in

the connector kit.

6. Connect the new W6 semi-rigid cable, included in the kit, between the A8A5 input attenuator (2) and the APC 3.5 mm

input connector (3). Tighten the SMA connectors to 8.5 inch pounds.

Installation Note E4407-90041 9

Replacing the Front Frame

1. Align the front frame subpanel rails with the chassis as shown in Figure 2.

2. Referring to Figure 2, connect the ribbon cable (3) to the front frame assembly.

3. Carefully slide the front frame toward the chassis, assuring the ribbon cable is not pinched between assemblies, and the RF

input connector lines up correctly with the opening in the front frame.

NOTE Make sure the water seal is still in place around the input connector (and around the A2 tracking generator

connector if the instrument is an Option 1DN) before reinstalling the front frame assembly.

4. Referring to Figure 2, replace the five screws (1), and the two screws (2) that secure the front frame to the chassis.

Tighten them to 9 inch-pounds.

Replacing the Dress Cover

1. Referring to Figure 1, place the spectrum analyzer on the work surface with the front frame (3) facing down.

2. Replace the instrument outer case and rear frame assembly (6), matching the grill (8) on the bottom of the case to the

bottom of the analyzer.

3. Fit the leading edge of the case completely into the slot (9) on the back of the front frame assembly.

4. Replace the four screws (5) to fasten the rear frame to the instrument. Tighten them to 21 inch-pounds.

Firmware Revision Verification

1. Turn on the analyzer and wait for the power-on alignments to complete. Check that there are no error messages displayed.

2. Press System, More, Show System. Make a note of the firmware revision and see if Option B72, Expansion Memory, is

listed on the display.

3. If the firmware revision is A.06.00 or later, the firmware does not need to be updated and you can skip steps 4through 6.

4. If your firmware revision is prior to A.06.00, you must update your analyzer firmware before the license key can be

activated.

5. If Option B72, Expansion Memory is installed, you should update the instrument firmware to the latest version using one

of the following methods:

• Download the instrument firmware via the world-wide web at http://www.agilent.com/find/esa_firmware. This entire

process of updating firmware will take approximately 45 minutes.

Note: If you are upgrading an EMC analyzer, go to www.agilent.com/find/emc_firmware.

• Receive the latest firmware update disk set by ordering upgrade Option UE2.

Note: Special instructions in the Agilent ordering configurator should have made you aware of Option UE2 in case

access to the internet wasn’t available.

6. If Option B72, Expansion Memory is not installed, you should update the instrument firmware to version A.07.06. This is

the latest version for instruments that do not have Option B72 installed.

• Download the instrument firmware via the world-wide web at http://www.agilent.com/find/esa_firmware_std-mem.

This entire process of updating firmware will take approximately 45 minutes.

• Order upgrade Option B72, which includes the expansion memory and the latest ESA firmware update disk set.

Installation Note E4407-90041

Obtaining a License Key and Activating the Option

The entitlement certificate supplied in this kit allows you to obtain a license key from our Agilent website so you can enable

this upgrade option. Once you have retrieved the license key, you can begin the process of activating the option.

1. Press System, More, More, Licensing, Option. When you press Option, the alpha editor will be activated. For

instructions on using the alpha editor, refer to the analyzer User’s Guide.

2. Use the alpha editor to enter the three-character designation for the option, in this case, “BAB”, that you want to activate.

3. Press Enter when done.

4. Press License Key. When you press License Key the alpha editor will be activated.

5. Use the alpha editor and the numeric keypad to enter the 12-character license key number (for example:

D7C374DABD5B) for the option that you want to activate.

6. Press Enter when done.

7. Press Activate to turn on the option.

8. If the option and license key entries were correct, a message stating “Option Activated” will appear on the analyzer

display.

9. Press System, More, Show System to verify existence of Option BAB.

Perform Adjustments and Performance Tests

Adjustments Required

The adjustments listed below are required following this upgrade installation. These adjustments can only be performed using

the software outlined in the Introduction of this installation note. The adjustments must be performed in the order that they are

listed below. They must also be done prior to running any performance verification testing.

• Frequency Response

Performance Testing Required

The performance tests listed below are the minimum recommended set that will verify the upgrade just installed is functioning

correctly. Performing these tests alone does not guarantee that the instrument meets all advertised performance specifications.

The performance test procedures can be found in the ESA Spectrum Analyzer Calibration Guide, or the tests can be performed

using the software outlined in the Introduction of this installation note.

• Frequency Response

• Displayed Average Noise Level

• Residual Responses

NOTE A full calibration is required to ensure the instrument meets all advertised performance specifications.

Otros manuales para ESA-E E4407B

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Instrumento de medición de Agilent Technologies

Agilent Technologies

Agilent Technologies 4294A Manual de usuario

Agilent Technologies

Agilent Technologies 86120C Manual de usuario

Agilent Technologies

Agilent Technologies 2200 TapeStation Manual de usuario

Agilent Technologies

Agilent Technologies E4991A Manual de usuario

Agilent Technologies

Agilent Technologies ESA-E Series Manual

Agilent Technologies

Agilent Technologies ESA-E E4402B Manual de usuario

Agilent Technologies

Agilent Technologies N1911A Instrucciones de funcionamiento

Agilent Technologies

Agilent Technologies U3401A Manual de usuario

Agilent Technologies

Agilent Technologies 85301B Manual de usuario

Agilent Technologies

Agilent Technologies HP 16500B Manual de servicio

Agilent Technologies

Agilent Technologies FRG-700 Manual de usuario

Agilent Technologies

Agilent Technologies FieldFox N9912A Guía de inicio rápido

Agilent Technologies

Agilent Technologies 16800 Series Hoja de datos

Agilent Technologies

Agilent Technologies E4404B Guía de inicio rápido

Agilent Technologies

Agilent Technologies E5070B ENA Series Manual de usuario

Agilent Technologies

Agilent Technologies 16700 SERIES LOGIC ANALYSIS SYSTEM 16700 Instrucciones de funcionamiento y seguridad

Agilent Technologies

Agilent Technologies Cary 60 Manual de usuario

Agilent Technologies

Agilent Technologies NFA Series Manual de usuario

Agilent Technologies

Agilent Technologies E444xAU Option H37 Manual de usuario

Agilent Technologies

Agilent Technologies 6890 Series Manual de instrucciones

Agilent Technologies

Agilent Technologies Agilent 4396B Manual de usuario

Agilent Technologies

Agilent Technologies 16089E Guía de inicio rápido

Agilent Technologies

Agilent Technologies 83438A Manual de usuario

Agilent Technologies

Agilent Technologies E4440AU Manual de instalación y operación

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario