Agilent Technologies E8362C Manual de instalación y operación

Agilent Part Number: E8362-90004

Printed in USA September 2008

Supersedes print date: December 2007

Installation Note

Extended Frequency Range Upgrade Kit

For E8362B/C PNA Series Microwave Network Analyzers WITHOUT

the Configurable Test Set Option

Network Analyzer

Model Number

Upgrade Kit

Part Number

Frequency

Extension

E8362B/C E8362-60109 20 GHz to 40 GHz

2Installation Note E8362-90004

WARRANTY STATEMENT

THE MATERIAL CONTAINED IN THIS DOCUMENT IS PROVIDED “AS IS,” AND IS SUBJECT TO

BEING CHANGED, WITHOUT NOTICE, IN FUTURE EDITIONS. FURTHER, TO THE MAXIMUM

EXTENT PERMITTED BY APPLICABLE LAW, AGILENT DISCLAIMS ALL WARRANTIES,

EITHER EXPRESS OR IMPLIED WITH REGARD TO THIS MANUAL AND ANY INFORMATION

CONTAINED HEREIN, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. AGILENT SHALL NOT BE

LIABLE FOR ERRORS OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES IN

CONNECTION WITH THE FURNISHING, USE, OR PERFORMANCE OF THIS DOCUMENT OR

ANY INFORMATION CONTAINED HEREIN. SHOULD AGILENT AND THE USER HAVE A

SEPARATE WRITTEN AGREEMENT WITH WARRANTY TERMS COVERING THE MATERIAL IN

THIS DOCUMENT THAT CONFLICT WITH THESE TERMS, THE WARRANTY TERMS IN THE

SEPARATE AGREEMENT WILL CONTROL.

DFARS/Restricted Rights Notice

If software is for use in the performance of a U.S. Government prime contract or subcontract,

Software is delivered and licensed as “Commercial computer software” as defined in DFAR

252.227-7014 (June 1995), or as a “commercial item” as defined in FAR 2.101(a) or as

“Restricted computer software” as defined in FAR 52.227-19 (June 1987) or any equivalent

agency regulation or contract clause. Use, duplication or disclosure of Software is subject to

Agilent Technologies’ standard commercial license terms, and non-DOD Departments and

Agencies of the U.S. Government will receive no greater than Restricted Rights as defined in

FAR 52.227-19(c)(1-2) (June 1987). U.S. Government users will receive no greater than

Limited Rights as defined in FAR 52.227-14 (June 1987) or DFAR 252.227-7015 (b)(2)

(November 1995), as applicable in any technical data.

Safety Notes

The following safety notes are used throughout this document. Familiarize yourself with each

of these notes and its meaning before performing any of the procedures in this document.

WARNING

Warning denotes a hazard. It calls attention to a procedure which,

if not correctly performed or adhered to, could result in injury or

loss of life. Do not proceed beyond a warning note until the

indicated conditions are fully understood and met.

CAUTION

Caution denotes a hazard. It calls attention to a procedure that, if not

correctly performed or adhered to, could result in damage to or destruction

of the instrument. Do not proceed beyond a caution sign until the indicated

conditions are fully understood and met.

Installation Note E8362-90004 3

Getting Assistance from Agilent

Assistance with test and measurements needs and information on finding a local Agilent

office are available on the Web at:

www.agilent.com/find/assist

If you do not have access to the Internet, please contact your Agilent field engineer.

NOTE

In any correspondence or telephone conversation, refer to the Agilent product by

its model number and full serial number. With this information, the Agilent

representative can determine whether your product is still within its warranty

period.

4Installation Note E8362-90004

About the Upgrade Kit

If you need assistance, refer to “Getting Assistance from Agilent” on page 3.

Description of the Upgrade

This upgrade kit is used to extend the frequency range of the:

• E8362B/C PNA microwave network analyzer from 20 GHz to 40 GHz

Products affected. . . . . . . . . . . . . . . . . . . . . . . . . . E8362B/C without Option 014,

Configurable Test Set

Installation to be performed by . . . . . . . . . . . . . . Agilent service center or personnel

qualified by Agilent

Estimated installation time . . . . . . . . . . . . . . . . . 2.5 hours

Estimated adjustment time . . . . . . . . . . . . . . . . . 0.5 hours

Estimated full instrument calibration time . . . . 4.5 hours

Installation Note E8362-90004 5

Items Included in the Upgrade Kit

Check the contents of your kit against the following list. If any item is missing or damaged,

contact Agilent Technologies. Refer to “Getting Assistance from Agilent” on page 3.

Table 1 Option 040 Upgrade Kit (E8362-60109) to Extend the E8362B/C to 40 GHz

Ref.

Desig. Description Qty Part Number

Parts for all analyzer options (except Option 014)

N/A Installation note (this document) 1 E8362-90004

N/A License key certificate 1 5964-5136

N/A Model number nameplate (for 40 GHz analyzer, E8363B) 1 E8363-80002

N/A Model number nameplate (for 40 GHz analyzer, E8363C) 1 E8363-80003

A21 SOMA 50 1 5087-7130

A23 Channel R1 detector

2 5087-7133

A24 Channel R2 detector

A25 Test port 1 coupler

2 5087-7518

A26 Test port 2 coupler

A27 Channel A first converter (mixer)

2 5087-7122

A30 Channel B first converter (mixer)

A38, A39 Bias tee (cable included) 2 5087-7233

N/A Machine screw M3.0 x 18 (for attaching A23 and A24 detectors) 4 0515-0666

N/A Machine screw M3.0 x 30 (for attaching SOMA 50) 4 0515-1349

N/A Ribbon cable, A21 SOMA 50 to A16 test set motherboard 1 8121-0818

N/A Cable, wrapped wire, detectors to A16 test set motherboard 2 E7340-60075

N/A Test set deck front panel 1 E8364-00014

W1 A12 source 20 to A21 SOMA 50 1 E8364-20036

W2 A21 SOMA 50 to A22 switch/splitter 1 E8364-20034

W3 A22 switch/splitter to A23 channel R1 detector 1 E8364-20144

W4 A22 switch/splitter to A24 channel R2 detector 1 E8364-20024

W37 A23 channel R1 detector to A16 test set motherboard J204 1 E8364-60121

6Installation Note E8362-90004

W38 A24 channel R2 detector to A16 test set motherboard J205 1 E8364-60122

W39 A21 SOMA 50 to A16 test set motherboard J206 1 E8364-60123

Parts for analyzers WITH NO RF hardware options

W7 A23 channel R1 detector to A28 channel R1 mixer 1 E8364-20025

W8 A24 channel R2 detector to A29 channel R2 mixer 1 E8364-20026

Parts for analyzers WITH Option UNL ONLY

W7 A23 channel R1 detector to A28 channel R1 mixer 1 E8364-20174

W8 A24 channel R2 detector to A29 channel R2 mixer 1 E8364-20175

Parts for analyzers WITH Options UNL and 016 ONLY

W7 A23 channel R1 detector to A28 channel R1 mixer 1 E8364-20149

W8 A24 channel R2 detector to A29 channel R2 mixer 1 E8364-20150

Table 1 Option 040 Upgrade Kit (E8362-60109) to Extend the E8362B/C to 40 GHz

Ref.

Desig. Description Qty Part Number

Installation Note E8362-90004 7

Installation Procedure for the Upgrade Kit

The network analyzer must be in proper working condition prior to installing this option. Any

necessary repairs must be made before proceeding with this installation.

WARNING

This installation requires the removal of the analyzer’s protective outer

covers. The analyzer must be powered down and disconnected from the

mains supply before performing this procedure.

Electrostatic Discharge Protection

Protection against electrostatic discharge (ESD) is essential while removing or connecting

cables or assemblies within the network analyzer.

Static electricity can build up on your body and can easily damage sensitive internal circuit

elements when discharged. Static discharges too small to be felt can cause permanent

damage. To prevent damage to the instrument:

•always wear a grounded wrist strap having a 1 MΩresistor in series with it when handling

components and assemblies.

•always use a grounded, conductive table mat while working on the instrument.

•always wear a heel strap when working in an area with a conductive floor. If you are

uncertain about the conductivity of your floor, wear a heel strap.

Figure 1 shows a typical ESD protection setup using a grounded mat and wrist strap. Refer to

“Tools Required for the Installation” on page 8 for part numbers.

Figure 1 ESD Protection Setup

8Installation Note E8362-90004

Overview of the Installation Procedure

Step 1. Verify the Model, Serial, and Option Numbers of the Analyzer

Step 2. Remove the Outer Cover

Step 3. Remove the Inner Cover

Step 4. Remove the Front Panel Assembly

Step 5. Disconnect the A12 Source 20 to A22 Switch/Splitter Cable at the A12 Source 20

Step 6. Raise the Receiver Deck

Step 7. Remove the Old Hardware and Cables

Step 8. Replace the A38 and A39 Bias Tees (Option UNL Only)

Step 9. Install the Remaining New Hardware

Step 10. Install the Remaining Cables

Step 11. Lower the Receiver Deck

Step 12. Connect the A12 Source 20 to A21 SOMA 50 Cable at the A12 Source 20

Step 13. Replace the Front Panel Nameplate

Step 14. Reinstall the Front Panel Assembly

Step 15. Reinstall the Inner and Outer Covers

Step 16. Enter the New Model Number

Step 17. Perform Post-Upgrade Adjustments and Calibration

Tools Required for the Installation

ESD Equipment and Supplies Required for the Installation

Description Agilent Part Number

T-8 TORX driver (set to 5 in-lbs) N/A

T-10 TORX driver (set to 9 in-lbs) N/A

T-20 TORX driver (set to 21 in-lbs) N/A

5/16-inch torque wrench (set to 10 in-lbs) N/A

1-inch torque wrench (set to 72 in-lbs) N/A

Description Agilent Part Number

ESD grounding wrist strap 9300-1367

5-ft grounding cord for wrist strap 9300-0980

2 x 4 ft conductive table mat and 15-ft grounding wire 9300-0797

ESD heel strap (for use with conductive floors) 9300-1308

Installation Note E8362-90004 9

Equipment Required for Post-Upgrade Adjustments

Step 1. Verify the Model, Serial, and Option Numbers of the Analyzer

Refer to the License Key Certificate supplied with the kit:

• Verify that the analyzer’s model and serial numbers match those on the certificate.

• Verify that the option number on the certificate matches the option described by this

installation note.

If the model, serial, or option number do not match the expected results, you will not be able

to install the option. If this is the case, contact Agilent for assistance. Refer to “Getting

Assistance from Agilent” on page 3.

Equipment Type Model or

Part Number

Alternate Model or

Part Number

Power meter E4418B/E4419B E4418A/E4419A

Power sensor, 2.4 mm 8487A None

Adapter, 2.4 mm (f) to 2.4 mm (f) 11900B 85056-60007

RF cable, 2.4 mm (f) to 2.4 mm (f) 85133C 85133E

10 Installation Note E8362-90004

Step 2. Remove the Outer Cover

CAUTION

This procedure is best performed with the analyzer resting on its front

handles in the vertical position. Do not place the analyzer on its front panel

without the handles. This will damage the front panel assemblies.

1. Disconnect the power cord (if it has not already been disconnected).

2. Using a T-20 TORX driver, remove the strap handles (item ①) by loosening the screws

(item ②) on both ends until the handle is free of the analyzer.

3. Using a T-20 TORX driver, remove the four rear panel feet (item ③) by removing the center

screws (item ④).

4. Slide the four bottom feet (item ⑤) off the cover.

5. Slide the cover off of the frame.

Figure 2 Outer Cover Removal

NOTE

The figure above shows the E8362B front panel and floppy disk drive. The

E8362C front panel has a slightly different appearance and does not

include a floppy disk drive.

Otros manuales para E8362C

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Instrumento de medición de Agilent Technologies

Agilent Technologies

Agilent Technologies 1680 series Manual de usuario

Agilent Technologies

Agilent Technologies Flow Tracker 1000 Series Manual de operación

Agilent Technologies

Agilent Technologies ENA Series Manual de usuario

Agilent Technologies

Agilent Technologies 4294A Manual de usuario

Agilent Technologies

Agilent Technologies 1156A Manual de usuario

Agilent Technologies

Agilent Technologies N5502A Manual de usuario

Agilent Technologies

Agilent Technologies 700 Series Manual de usuario

Agilent Technologies

Agilent Technologies PSA Series Manual de instalación y operación

Agilent Technologies

Agilent Technologies 1146B Manual de usuario

Agilent Technologies

Agilent Technologies 8719ES Manual de usuario

Agilent Technologies

Agilent Technologies 86082A Manual de usuario

Agilent Technologies

Agilent Technologies 4339B Manual de usuario

Agilent Technologies

Agilent Technologies 8753ET Guía de configuración

Agilent Technologies

Agilent Technologies 4291B Manual de usuario

Agilent Technologies

Agilent Technologies DSOX4USBSQ USB 2.0 Manual de usuario

Agilent Technologies

Agilent Technologies PSA Series Guía de inicio rápido

Agilent Technologies

Agilent Technologies U5303A Guía del usuario

Agilent Technologies

Agilent Technologies K6460 Manual de instalación y funcionamiento

Agilent Technologies

Agilent Technologies 85051B Manual

Agilent Technologies

Agilent Technologies Flow Tracker 1000 Manual de usuario

Agilent Technologies

Agilent Technologies 81200 Manual de usuario

Agilent Technologies

Agilent Technologies ICP-MS Series Instrucciones de funcionamiento

Agilent Technologies

Agilent Technologies 4395A Manual de usuario

Agilent Technologies

Agilent Technologies J2300D Manual de lista de piezas

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario