Agilent Technologies 1156A Manual de usuario

A

User’s Guide

Publication number 01156-97002

September 2005

For Safety and Regulatory information, see the pages at the back of this guide.

1156A 1.5 GHz Active Probe

99 Washington Street

Melrose, MA 02176

Phone 781-665-1400

Toll Free 1-800-517-8431

Visit us at www.TestEquipmentDepot.com

Back to the Agilent 1156a Product Info Page

In This Book

This guide provides user and service information for the 1156A 1.5 GHz Active

Probe.

Chapter 1 gives you general information such as inspection, cleaning,

accessories supplied, and specifications and characteristics of the probe.

Chapter 2 shows you how to operate the probe and gives you information about

some important aspects of probing and how to get the best results with your

probe.

Chapter 3 provides service information.

Contents

1General Information

To inspect the probe 7

Accessories Supplied 8

Replaceable Parts and Additional Accessories 10

Characteristics and Specifications 11

General Characteristics 12

To use the probe 14

Probe handling considerations 14

Cleaning the probe 14

Using Probe Accessories 15

To connect the probe 16

2Operating the Probe

110 Ohm Resistive Signal Pin (Green) and Solderable Ground

Socket 21

130 Ohm Resistive Signal Pin (Orange) and Ground Blade

Assembly 25

5 cm Resistive Signal Leads and Solderable SMT or Solderable

Through-hole Ground Pin 29

Socket-end 10 cm Resistive Signal Lead and Solderable SMT or

Solderable Through-hole Ground Pin 33

Micro Clip 37

Undamped Accessories 37

3Service

Service Strategy 42

To return the probe to Agilent Technologies for service 43

Troubleshooting 44

Failure Symptoms 44

Probe Calibration Fails 44

Incorrect High Frequency Response 44

Incorrect Low Frequency Response (pulse flatness) 45

Incorrect Input Resistance 45

Incorrect Offset 45

Offset Will Not Zero 45

Verifying probe input resistance 46

1156A 1.5 GHz Active Probe

The 1156A 1.5 GHz Active Probe is a probe solution for high-frequency

applications. This probe is compatible with the AutoProbe Interface

which completely configures the Infiniium series of oscilloscopes for the

probe.

General Information

To inspect the probe

❏Inspect the shipping container for damage.

Keep a damaged shipping container or cushioning material until the contents of

the shipment have been checked for completeness and the instrument has been

checked mechanically and electrically.

❏Check the accessories.

Accessories supplied with the instrument are listed in "Accessories Supplied" in

table 1-1 later in this chapter.

• If the contents are incomplete or damaged notify your Agilent Technologies

Sales Office.

❏Inspect the probe.

• If there is mechanical damage or defect, or if the probe does not operate

properly or pass calibration tests, notify your Agilent Technologies Sales

Office.

• If the shipping container is damaged, or the cushioning materials show signs

of stress, notify the carrier as well as your Agilent Technologies Sales Office.

Keep the shipping materials for the carrier’s inspection. The Agilent

Technologies Office will arrange for repair or replacement at Agilent

Technologies’ option without waiting for claim settlement.

Figure 1-1

1156A Active Probe

01158e03.cdr

5 Accessory Vials

Accessories

Container

Included with

the probe is an

accessories

container and 5

accessory

vials. All the

included

accessories

are shown in

figure 1-2.

General Information

Accessories Supplied

The following figure and table show the accessories supplied with the 1156A

Active Probe.

Figure 1-2

General Information

Accessories Supplied

Table 1-1

Accessories Supplied

Item Description Qty Agilent Part Number

1s 130 Ωresistive signal pin (orange) 12 01156-27616

2s Solderable-tip 5 cm resistive signal lead 2 01156-82106

3s Socket-end 5 cm resistive signal lead 2 01156-82105

4s Socket-end 10 cm resistive signal lead 2 01156-82108

5sg Micro clip 25063-2180

1g Ground blade assembly 12 01156-23701

2g Solderable SMT ground pin 12 1253-5054

3g Solderable through-hole ground pin 12 1252-7150

4g Offset ground pin 12 01156-27606

5g Solderable-tip 5 cm ground lead 2 01156-82107

6g Socket-end 5 cm ground lead 2 01156-82103

7g Socket-end 5 cm, 90° pin ground lead 2 01156-82104

General Information

Replaceable Parts and Additional Accessories

Table 1-2

Replaceable Parts and Additional Accessories

Agilent Part Number Description Qty

E2638A Solderable-tip 5 cm resistive signal lead

Solderable-tip 5 cm ground lead

E2639A Micro clip 4

E2640A 130 Ωresistive signal pin (orange) 8

E2641A Ground blade assembly 8

E2637A Precision Measurement Kit

includes 2 solderable ground sockets and 2

110 Ωresistive signal pins (green)

E2654A EZ-Probe®positioner 1

General Information

Characteristics and Specifications

The following characteristics are typical for the active probe.

Table 1-3

Characteristics

1 Denotes warranted specifications, all others are typical.

2 For waveforms with edges > 3 ns, the dynamic range is > 12.0 Vpeak-to-peak

3 Installation category (overvoltage category) I: Signal level, special equipment, or parts of

equipment, telecommunication, electronic, etc., with smaller transient overvoltages than

installation category (overvoltage category) II.

Bandwidth1(-3 dB) > 1.5 GHz

System bandwidth (-3 dB) 1156A with 54832B/D or 54835A scope: 1 GHz

Rise and Fall Time (10% to 90%) < 233 ps calculated from

Input Capacitance 0.8 pF

Input Resistance1100 kΩ \1%

Flatness, Swept Response 0.2 dB, 100 kHz to 100 MHz

0.4 dB, 100 MHz to 1.5 GHz

Flatness, Step Response 15% overshoot, 35 ps input edge

10% overshoot: 75 ps input edge; 2%: 1 ns after edge

Dynamic Range2> 5.0 V peak-to-peak

DC Attenuation 10:1

Offset error referred to input <\30 mV

Offset Range ±15.0 V

Offset Gain Accuracy <\3% of setting

Noise referred to input 3.0 mVrms

Propagation Delay 5.5 ns

Maximum Input Voltage340 V peak, CAT I

ESD Tolerance > 5 kV from 100 pF, 300 ΩHBM

Temperature Drift Offset: < 1.0 mV/°C

Attenuation: < 0.1 %/°C

0.35

Bandwidth

-----------------------------=

General Information

General Characteristics

The following general characteristics apply to the active probe.

Table 1-4

General Characteristics

Environmental Conditions

Operating Non-operating

Temperature 0 °C to +55 °C−40 °C to +70 °C

Altitude 4000 meter (13,000 ft)

Humidity up to 95% relative humidity

(non-condensing) at +40 °C

up to 90% relative humidity at +65 °C

Power Requirements +12 Vdc @ 3 mA typical

+5 Vdc @ 35 mA typical

-5 Vdc @ 37 mA typical

0.4 W

(voltages supplied by AutoProbe

Interface)

Weight approximately 0.69 kg

Dimensions Refer to the outline in figure 1-3.

Pollution degree 2 Normally only non-conductive pollution occurs. Occasionally, however, a

temporary conductivity caused by condensation must be expected.

Indoor use

Tabla de contenidos

Otros manuales de Instrumento de medición de Agilent Technologies

Agilent Technologies

Agilent Technologies E5070B ENA Series Manual de usuario

Agilent Technologies

Agilent Technologies 4155C Manual de usuario

Agilent Technologies

Agilent Technologies E8362C Manual de usuario

Agilent Technologies

Agilent Technologies E8362B Manual de usuario

Agilent Technologies

Agilent Technologies U3051C Manual del propietario

Agilent Technologies

Agilent Technologies 8712ET Manual de usuario

Agilent Technologies

Agilent Technologies 4339B Manual de usuario

Agilent Technologies

Agilent Technologies 3200D Manual de usuario

Agilent Technologies

Agilent Technologies E8356A Manual de instalación y operación

Agilent Technologies

Agilent Technologies PNA Series Manual de instalación y operación

Agilent Technologies

Agilent Technologies E4991A Manual de usuario

Agilent Technologies

Agilent Technologies 55B AA Manual de usuario

Agilent Technologies

Agilent Technologies 35670A Manual de usuario

Agilent Technologies

Agilent Technologies E444 AU Series Manual de usuario

Agilent Technologies

Agilent Technologies N9340B Manual

Agilent Technologies

Agilent Technologies E5406A-Pro Series Manual de usuario

Agilent Technologies

Agilent Technologies 8453 Manual de usuario

Agilent Technologies

Agilent Technologies 8504B Manual de usuario

Agilent Technologies

Agilent Technologies N9010A Manual de usuario

Agilent Technologies

Agilent Technologies 16962A Manual de usuario

Agilent Technologies

Agilent Technologies 7820A Guía del usuario

Agilent Technologies

Agilent Technologies N5242A Manual de usuario

Agilent Technologies

Agilent Technologies E5071C ENA Series Manual de usuario

Agilent Technologies

Agilent Technologies E4402BU Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario