Agilent Technologies G4560A Manual de usuario

Agilent Technologies

Agilent G4560A Upgrade Kit

For the Agilent 7697A Headspace Sampler

Installation Guide

Parts Supplied

The Agilent 7697A Upgrade Kit comes in three boxes described in Table 1,

Table 2, and Table 3.

Table 1 Box 1 (labeled G4556-67009)

Description Quantity

111 Vial Model Oven Assembly 1

Table 2 Box 2 (labeled G4556-67005)

Description Quantity

111 Vial Model Cover Kit includes: 1

•T-20 Torx screws, 5/pk 1

•Front cover 1

•Top instrument cover (with 3 cables, pre installed) 1

•Cable, G4556-60140, BCR power to panel cable

•Cable, G4556-60141, Data cable

•Cable, G4556-60142, Panel tray power cable

Table 3 Box 3 (labeled G4556-64014)

Description Quantity

111 Vial Model Tray 1

•111 Vial Model Tray Ship Kit, G4556-60830 (3 vial racks) 1

•7697A Tray 1

2Installation Guide

Agilent G4560A Upgrade Kit

Parts Identification

Figure 1 111 Vial Model Oven Assembly

Agilent G4560A Upgrade Kit

Installation Guide 3

Figure 2 111 Vial Cover Kit

T-20 Torx screws

Front cover

Top instrument cover

0515-0433

G4556-81020

G4556-00217

Panel tray power cable

G4556-60142

BCR power to panel cable

G4556-60140

Data cable

G4556-60141

4Installation Guide

Agilent G4560A Upgrade Kit

Figure 3 G4556-64014 - 111 Vial Model Tray kit

7697A Tray Assembly

Shipping clamp

Shipping clamp removal instructions

Vial racks

Agilent G4560A Upgrade Kit

Installation Guide 5

Tools Required

•T- 20 Torx driver

•Agilent Instrument Utilities software, version B.01.05 SP1 or later

•FSElicensefor Agilent Instrument Utilities software

•Antistatic (ESD) wrist strap

•Lint- free gloves

•Lint- free cloth

Installation Procedure

Read the Agilent 7697A Headspace Sampler Safety Manual before

upgrading the headspace sampler, and whenever needed. The safety

manual describes precautions to follow when installing and using the

headspace sampler, as well as important regulatory information.

Confirm that all parts have been received. Refer to “Parts Supplied” and

“Parts Identification” for information.

Prepare the GC and 7697A 12-Vial headspace sampler

1Set your GC oven, GC inlet, headspace oven, and transfer line to

ambient temperatures and wait for them to cool.

2Once the GC oven, headspace oven, and transfer line have cooled to

ambient temperature, turn off the headspace and unplug the power

cord.

3Turn all gas flows off at their sources.

4Disconnect the transfer line from the GC inlet. Secure the transfer line

to its support bracket.

5Open the rotating top cover and remove all vials from the carousel.

CAUTION

Wear clean, lint-free gloves to prevent contamination of parts with dirt and skin oils.

CAUTION

Make sure you use an antistatic (ESD) wrist strap and take other antistatic

precautions during the following installation procedures.

6Installation Guide

Agilent G4560A Upgrade Kit

Remove covers from the headspace sampler

Remove the covers shown in Figure 4 from the headspace sampler.

Figure 4 Covers to remove from the 12 vial model headspace sampler

Front cover

Top c ove r tr ay

Top c over

Right panel assembly

Rotating top cover

Pneumatics front cover

Agilent G4560A Upgrade Kit

Installation Guide 7

1Remove the rotating top cover (Figure 5).

aLift the rotating top cover from the front so that the two

thumbscrews are accessible underneath.

bUnhinge and remove the tray cover by pulling one of the two

thumbscrews inward while lifting the tray cover off of the chassis.

Once the thumbscrew disconnects, repeat the same action for the

second thumbscrew.

cRemove the rotating top cover.

2Remove the top cover. (See Figure 4.)

aRemove two T-20 Torx screws on the back of the headspace sampler.

bLift and remove the top cover tray, and remove the T- 20 Torx screw

under the top cover tray.

cRemove the top cover.

3Remove the front cover. (See Figure 4.)

aIf necessary, move the headspace sampler away from the GC to

access the T- 20 Torx screws on the left side of the headspace.

bRemove two T- 20 Torx screws on the left side of the headspace

sampler.

cRemove the front cover.

4Remove the right panel assembly. (See Figure 4.)

aRemove the two T- 20 Torx screws on the right panel assembly.

bLift up and remove the right panel assembly.

Figure 5 Removing the rotating top cover

Rotating top cover

Thumbscrews

8Installation Guide

Agilent G4560A Upgrade Kit

5Remove the pneumatics front cover. (See Figure 4.)

aRemove the T- 20 screw that secures the cover in place (Figure 6).

bSlide out, then lift to remove the pneumatics front cover.

Remove the oven assembly

Figure 6 T-20 Torx screw securing the pneumatics front cover

CAUTION

Do not remove the pneumatics assembly completely. Be careful to not damage any

attached cables and gas lines when moving the pneumatics assembly.

Agilent G4560A Upgrade Kit

Installation Guide 9

1Remove the pneumatics assembly from the headspace sampler.

aCompletely loosen the two T- 20 Torx captive thumbscrews that are

inset at the front of the pneumatics assembly (Figure 7).

bCompletely loosen the T- 20 Torx captive thumbscrew in the back

area of the pneumatics assembly (Figure 8).

cLift the pneumatics assembly straight up, rotate the unit about 90

degrees counterclockwise, and lay it across the back of the headspace

sampler.

dIf desired, disconnect the pneumatics assembly cables at the PCM

and heater locations. The cable harness should remain connected to

Figure 7 Front T-20 Torx thumbscrews

Figure 8 Back T-20 Torx thumbscrew

10 Installation Guide

Agilent G4560A Upgrade Kit

the electronics control board for easy re- installation.

2Disconnect the 12- vial model heater assembly cables from the

headspace sampler.

aDisconnect the oven heater cable (Figure 9). The oven heater

connection jack is located on the left side behind the oven

compartment facing the front of the headspace sampler.

bDisconnect the ribbon cable from P1 on the control board. The

control board is located behind the oven compartment and faces the

back of the headspace sampler.

Figure 9 Disconnecting the oven heater connection

Figure 10 Disconnecting the ribbon cable from P1 on the control board

Tabla de contenidos

Otros manuales de Equipo de laboratorio de Agilent Technologies

Agilent Technologies

Agilent Technologies 490 Micro GC Manual de usuario

Agilent Technologies

Agilent Technologies 1100 Series Manual de usuario

Agilent Technologies

Agilent Technologies AriaMx Manual de instrucciones

Agilent Technologies

Agilent Technologies 1200 series Manual de usuario

Agilent Technologies

Agilent Technologies 7890B Manual de instalación

Agilent Technologies

Agilent Technologies Velocity11 VSpin Manual de usuario

Agilent Technologies

Agilent Technologies 8860 Manual de usuario

Agilent Technologies

Agilent Technologies 1260 Infinity Manual de usuario

Agilent Technologies

Agilent Technologies 1260 Infinity VL Manual de usuario

Agilent Technologies

Agilent Technologies 7890A Guía del usuario

Agilent Technologies

Agilent Technologies Bravo Guía de configuración

Agilent Technologies

Agilent Technologies IMG-500 Manual de usuario

Agilent Technologies

Agilent Technologies PR02 Manual de usuario

Agilent Technologies

Agilent Technologies 55 AA Manual de usuario

Agilent Technologies

Agilent Technologies ZORBAX Series Manual de usuario

Agilent Technologies

Agilent Technologies G1982-6700 Manual de usuario

Agilent Technologies

Agilent Technologies 1260 Infinity II Manual de usuario

Agilent Technologies

Agilent Technologies 7694 Manual de usuario

Agilent Technologies

Agilent Technologies G1289 Manual de usuario

Agilent Technologies

Agilent Technologies 1200 series Manual de usuario

Agilent Technologies

Agilent Technologies 1100 Series Manual de usuario

Agilent Technologies

Agilent Technologies Labware MiniHub G5584A Manual de usuario

Agilent Technologies

Agilent Technologies G1701DA Manual de usuario

Agilent Technologies

Agilent Technologies 8453 Manual de usuario

Manuales populares de Equipo de laboratorio de otras marcas

Qiagen

Qiagen DML 3000 Manual de usuario

Queensgate

Queensgate NANOSCAN OP400 Manual de programación

Conviron

Conviron GEN1000-GE Manual de usuario

Parr Instrument

Parr Instrument 4560 Manual de instrucciones

IKA

IKA IC control Manual de usuario

Integra

Integra DOSE IT Manual de usuario

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Manual de usuario

NI PXI-5422 Manual

Collomix

Collomix Aqix Manual de usuario

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Manual de usuario

Ocean Insight

Ocean Insight FLAME-NIR+ Manual de usuario

Parker

Parker ALIGN-MG-NA Manual de usuario

BD 644787 Manual de usuario

DENTAURUM

DENTAURUM Compact Megaplus Manual de usuario

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Manual de usuario

VWR

VWR SAS Super IAQ Manual de usuario

illumina

illumina MiSeqDx Manual de usuario

Yamato

Yamato BM510 Manual de usuario