Agilent Technologies Multiple Channel Controller 85330A Manual de servicio

Agilent Technologies 85330A

Multiple Channel Controller

Operating, Programming,

and Service Manual

Part number: 85330-90019

Printed in USA

October 2002

Supersedes November 1999

ii 85330A Multiple Channel Controller

Notice

Restricted Rights Legend

Use, duplication, or disclosure by the U.S. Government is subject to

restrictions as set forth in subparagraph (c)(1)(ii) of the Rights in Technical

Data and Computer Software clause at DFARS 252.227-7013 for DOD

agencies, and subparagraphs (c)(1) and (c)(2) of the Commercial Computer

Software Restricted Rights clause at FAR 52.227-19 for other agencies.

85330A Multiple Channel Controller iii

What You’ll Find in This Manual…

Chapter 1 •Installation - Shows how a standard Agilent 85330A system is installed.

If you purchased a preconﬁgured system, Agilent has provided

documentation that contains installation information for your speciﬁc

system. Use the documentation for your special system instead of the

information in this chapter.

Chapter 2 •Performance Veriﬁcation - Explains how to verify that the 85330A

system is operating properly.

Chapter 3 •Operator’s Check - This is a quick check of the system to make sure it is

operating properly.

Chapter 4 •General Information - Describes a typical system, and includes

information on:

❍Supplied items

❍Features

❍85330A connectors

❍Accessories

❍Speciﬁcations

❍Environmental Characteristics

❍Compatible instruments

Chapter 5 •Manual Operation - Describes functions that can be performed manually

using the multiple channel controller’s front panel softkeys.

Chapter 6 •Programming - Describes the 85330A programming fundamentals with

examples.

Chapter 7 •Remote Programming Command Reference - A dictionary of the

85330As programming commands.

Chapter 8 •In Case of Difﬁculty - How to solve common system problems.

Chapter 9 •Service - Explains how to determine if the 85330A speciﬁc control cards

are working. This chapter does not explain how to troubleshoot the VXI

mainframe, which has its own service documentaiton.

iv 85330A Multiple Channel Controller

Appendix •Glossary of Terms - This glossary deﬁnes special terminology

associated with this system. Words shown in bold text are deﬁned in the

glossary.

Warranty

Certiﬁcation Agilent Technologies certiﬁes that this product met its published

speciﬁcations at the time of shipment from the factory. Agilent further

certiﬁes that its calibration measurements are traceable to the United States

National Institute of Standards and Technology (NIST, formerly NBS), to the

extent allowed by the Institute’s calibration facility, and to the calibration

facilities of other International Standards Organization members.

Documentation

Warranty THE MATERIAL CONTAINED IN THIS DOCUMENT IS

PROVIDED "AS IS," AND IS SUBJECT TO BEING CHANGED,

WITHOUT NOTICE, IN FUTURE EDITIONS. FURTHER, TO

THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW,

AGILENT DISCLAIMS ALL WARRANTIES, EITHER EXPRESS

OR IMPLIED WITH REGARD TO THIS MANUAL AND ANY

INFORMATION CONTAINED HEREIN, INCLUDING BUT NOT

LIMITED TO THE IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR

PURPOSE. AGILENT SHALL NOT BE LIABLE FOR ERRORS

OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES IN

CONNECTION WITH THE FURNISHING, USE, OR

PERFORMANCE OF THIS DOCUMENT OR ANY

INFORMATION CONTAINED HEREIN. SHOULD AGILENT

AND THE USER HAVE A SEPARATE WRITTEN AGREEMENT

WITH WARRANTY TERMS COVERING THE MATERIAL IN

THIS DOCUMENT THAT CONFLICT WITH THESE TERMS,

THE WARRANTY TERMS IN THE SEPARATE AGREEMENT

WILL CONTROL.

Assistance Product maintenance agreements and other customer assistance agreements

are available for Agilent products.

For assistance, call your local Agilent Technologies ofﬁce (refer to “Service

and Support” on page v).

85330A Multiple Channel Controller v

Service and Support

Any adjustment, maintenance, or repair of this product must be performed

by qualiﬁed personnel. Contact your customer engineer through your local

Agilent Technologies Service Center. You can ﬁnd a list of local service

representatives on the Web at:

http://www.agilent.com/find/assist

Click on “Contact Us” and select your country.

If you do not have access to the Internet, one of these centers can direct you

to your nearest Agilent Technologies representative:

United States (800) 403-0801

(800) 593-6635 for on-site service of systems

Canada (877) 429-9969

Europe (41 22) 780.6111 (Switzerland)

(33 1) 69 82 66 66 (France)

(49 7031) 464-6222 (Germany)

(44 188) 9696622 (Great Britain)

Japan 0120-32-0119

Latin America (11) 7297-3700 (Brazil)

Australia/New

Zealand 1-800-802-540 (Australia)

0800-738-378 (New Zealand)

Asia-Paciﬁc 080-047-669

vi 85330A Multiple Channel Controller

Safety and Regulatory Information

Review this product and related documentation to familiarize yourself with

safety markings and instructions before you operate the instrument. This

product has been designed and tested in accordance with international

standards.

WARNING The WARNING notice denotes a hazard. It calls attention to a procedure,

practice, or the like, that, if not correctly performed or adhered to, could result

in personal injury. Do not proceed beyond a WARNING notice until the

indicated conditions are fully understood and met.

CAUTION The CAUTION notice denotes a hazard. It calls attention to an operating

procedure, practice, or the like, which, if not correctly performed or adhered

to, could result in damage to the product or loss of important data. Do not

proceed beyond a CAUTION notice until the indicated conditions are fully

understood and met.

Instrument Markings

The ON symbol. The ON symbol is used to mark the

positions of the instrument line switch.

The OFF symbol. The OFF symbol is used to mark the

positions of the instrument line switch.

The ON symbol. The ON symbol is used to mark the

positions of the instrument line switch.

The OFF symbol. The OFF symbol is used to mark the

positions of the instrument line switch.

This symbol indicates that the power line switch is OFF or in STANDBY position.

The AC symbol. The AC symbol is used to indicate the

required nature of the line module input power.

The instruction documentation symbol. The product is

marked with this symbol when it is necessary for the user

to refer to the instructions in the documentation.

85330A Multiple Channel Controller vii

Safety Earth

Ground This is a Safety Class I product (provided with a protective earthing

terminal). An uninterruptible safety earth ground must be provided from the

main power source to the product input wiring terminals, power cord, or

supplied power cord set. Whenever it is likely that the protection has been

impaired, the product must be made inoperative and secured against any

unintended operation.

Before Applying Power Verify that the product is conﬁgured to match the available main power

source as described in the input power conﬁguration instructions in this

manual. If this product is to be powered by autotransformer, make sure the

common terminal is connected to the neutral (grounded) side of the ac power

supply.

WARNING No operatorserviceablepartsinside.Referservicing toqualiﬁedpersonnel.To

prevent electrical shock do not remove covers.

WARNING For continued protection against ﬁre hazard, replace line fuse only with the

same type and ratings (type nA/nV). The use of other fuses or materials is

prohibited.

WARNING To prevent electrical shock, disconnect the 85330A from mains before

cleaning. Use a dry cloth or one slightly dampened with water to clean the

external case parts. Do not attempt to clean internally.

The CE mark is a registered trademark of the European

Community. (If accompanied by a year, it is when the design

was proven.)

The CSA mark is a registered trademark of the Canadian

Standards Association.

This is a symbol of an Industrial Scientiﬁc and Medical

Group 1 Class A product.

ICES /

NMB-001 This is a marking to indicate product compliance with the

Canadian Interference-Causing Equipment Standard

(ICES-001).

The C-Tick mark is a registered trademark of the

Australian Spectrum Management Agency.

viii 85330A Multiple Channel Controller

WARNING If this product is not used as speciﬁed, the protection provided by the

equipmentcouldbe impaired. This productmustbeused in anormalcondition

(in which all means for protection are intact).

CAUTION Always use the three-prong ac power cord supplied with this product.

Failure to ensure adequate earth grounding by not using this cord may cause

product damage.

CAUTION Install the instrument according to the enclosure protection provided. This

instrument does not protect against the ingress of water.

This instrument protects against ﬁnger access to hazardous parts with the

enclosure.

85330A Multiple Channel Controller ix

Manufacturers Declaration

This is to certify that this product meets the radio frequency interference

requirements of Directive FTZ 1046/1984. The German Bundespost has

been notiﬁed that this equipment was put into circulation and has been

granted the right to check the product type for compliance with these

requirements.

This product has be designed and tested in accordance with IEC Publication

1010, Safety Requirements for Electronic Measuring Apparatus, and has

been supplied in a safe condition. The instruction documentation contains

information and warnings which must be followed by the user to ensure safe

operation and to maintain the product in a safe condition.

NOTE If test and measurement equipment is operated with unshielded cables

and/or used for measurements on open set-ups, the user must insure that

under these operating conditions, the radio frequency interference limits are

met at the boarder of his premises.

Hiermit wird bescheinigt, dass dieses Gerät/System in Übereinstimmung mit

den Bestimmungen von Postverfügung 1046/84 funkentstört ist.

Der Deutschen Bundespost wurde das Inverkehrbringen dieses

Gerät/Systems angezeight und die Berechtigung zur Überprüfung der Serie

auf Einhaltung der Bestimmungen eingeräumt.

Zustzinformation für Mess-und Testgeräte:

Werden Mess- und Testgeräte mit ungeschirmten Kabeln und/oder in

offenen Messaufbauten verwendet, so ist vom Betreiber sicherzustellen, dass

die Funk-Entstörbestimmungen unter Betriebsbedingungen an seiner

Grundstücksgrenze eingehalten werden.

Sound Emmisions This is to declare that this product is in conformance with the German

Regulation on Noise Declaration for Machines (Laermangabe nach der

maschinenlaermrerordnung -3. GSGV Deutschland).

Acoustic Noise Emission Geraeuschemission

LpA < 70 dB

Operator Position

Normal Position

per ISO 7779

LpA < 70 dB

am Arbeitsplatz

normaler Betrieb

nach DIN 45635 t. 19

x85330A Multiple Channel Controller

Manufacturers Declaration

European Contact: Your local Hewlett-Packard Sales and Service Office or Hewlett-Packard GmbH Department HQ-

TRE, Herreneberger Strasse 130, D71034 Boblingen, Germany (FAX +49-7031-14-3143)

DECLARATION OF CONFORMITY

Accordin

to ISO/IEC Guide 22 and EN 45014

Manufacturer’s Name: Hewlett-Packard Co.

Manufacturer’s Address: 1400 Fountaingrove Parkway

Santa Rosa, CA 95403-1799

USA

Declares that the product:

Product Name: Multiple Channel Controller

Model Number: HP 85330A

Product Options: This declaration covers all options of the above

product.

Conforms to the following product specifications:

Safety:IEC 61010-1:1990 / EN 61010-1:1993

CAN/CSA-C22.2 No. 1010.1-92

EMC: CISPR 11:1990/EN 55011:1991 Group 1, Class A

IEC 801-2:1984/EN 50082-1:1992 4 kV CD, 8 kV AD

IEC 801-3:1984/EN 50082-1:1992 3 V/m, 27-500 MHz

IEC 801-4:1988/EN 50082-1:1992 0.5 kV sig. lines, 1 kV power lines

Supplementary Information:

The product herewith complies with the requirements of the Low Voltage Directive

73/23/EEC and the EMC Directive 89/336/EEC and carries the CE-marking accordingly.

The controller was tested with HP 85331A and HP 85332A switches.

Santa Rosa, CA, USA 12 July 1999 Greg Pfeiffer/Quality Engineering Manager

Tabla de contenidos

Otros manuales de Controladores de Agilent Technologies

Agilent Technologies

Agilent Technologies G2743A Manual de instrucciones

Agilent Technologies

Agilent Technologies 4UHV Manual de usuario

Agilent Technologies

Agilent Technologies Turbo-V 81-AG Manual de usuario

Agilent Technologies

Agilent Technologies TwisTorr 84 FS PCB Manual de usuario

Agilent Technologies

Agilent Technologies 969-9871 Manual de usuario

Agilent Technologies

Agilent Technologies Eyesys Mini-B/A Manual de usuario

Agilent Technologies

Agilent Technologies 78581B Instrucciones de instalación y mantenimiento

Agilent Technologies

Agilent Technologies Turbo-V 2000HT Manual de usuario

Agilent Technologies

Agilent Technologies 8169A Manual de usuario

Agilent Technologies

Agilent Technologies ETC 60 Manual de usuario

Agilent Technologies

Agilent Technologies TwisTorr Medium-TMP Rack Manual de usuario

Agilent Technologies

Agilent Technologies TwisTorr 305 FS Series Manual de usuario

Agilent Technologies

Agilent Technologies W2642A Manual de usuario

Agilent Technologies

Agilent Technologies Turbo-V 1000HT Manual de usuario

Agilent Technologies

Agilent Technologies Turbo-V 550 Manual de usuario

Agilent Technologies

Agilent Technologies X3501-64005 Manual de usuario

Agilent Technologies

Agilent Technologies 4UHV Manual de usuario

Agilent Technologies

Agilent Technologies RS-232 Manual de usuario

Agilent Technologies

Agilent Technologies TwisTorr Medium-TMP X3501-64016 Manual de usuario

Agilent Technologies

Agilent Technologies 6850 GCs Manual de instrucciones

Agilent Technologies

Agilent Technologies 929-0022 Manual de usuario

Agilent Technologies

Agilent Technologies 11896A Manual

Agilent Technologies

Agilent Technologies Turbo-V 750/850-AG Manual de usuario

Agilent Technologies

Agilent Technologies PCG-750 Manual de usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario