Agilent Technologies Agilent 35900E Manual de usuario

Agilent 35900E Dual Channel Interface

Service Manual

35900E Dual Channel Interface

Agilent 35900E Service Manual

Agilent Technologies, Inc.

2850 Centerville Road

Wilmington, DE 1 808-1610

USA

adaptation, or translation without

permission is prohi ited, except as

allowed under the copyright laws.

Part num er 35900-90417

First Edition, MAY 2000

Replaces Part No. 35900-90410,

Operating and Service Manual.

HP® is a registered trademark of

Hewlett-Packard Co.

Printed in USA

Electrical Shock Hazard

WARNING

This product is a Safety Class 1

instrument (provided with a protective

earth terminal). To avoid electrical

shock, the instrument must e

connected to the AC power supply mains

through a three-conductor power cord,

with the third wire firmly connected to

an electrical ground (safety ground) at

the power outlet. Any interruption of the

protective (grounding) conductor or

disconnection of the protective earth

terminal, under a fault condition could

cause a shock, that could result in

personal injury.

Safety Sy bols

CAUTION

A caution calls attention to a condition

or possi le situation that could damage

or destroy the product or the user’s

work.

WARNING

A warning calls attention to a condition

or possi le situation that could cause

injury to the user.

Released: MAY 2000 Agilent 35900E Service Manual 4

Contents

Chapter 1: Introduction

Manual Overview ....................................................................................................... 6

Chapter 2:

Troubleshooting the 35900E

Verify the 35 00E is Ready for Operation .............................................................. 8

In Case of Difficulty .................................................................................................. 8

Possible Causes for Failure...............................................................................

Verify the System is Ready for Operation ..............................................................

Chapter 3: Parts Replacement

Overview .................................................................................................................. 11

Parts List for the 35 00E ................................................................................. 12

Remove/Replace the Top Cover ............................................................................ 13

Remove/Replace the Front Panel .......................................................................... 14

Remove/Replace the Power Supply ...................................................................... 15

Remove the MIO Bracket ....................................................................................... 15

Remove the Connector Board ............................................................................... 16

Remove/Replace the Mother Board ...................................................................... 16

Remove/Install the SIMM Memory Boards .......................................................... 17

Chapter : Instrument Parts Breakdown

Parts Breakdown—Figure 4 .................................................................................. 1

Parts Breakdown—Figure 5 .................................................................................. 21

Released: MAY 2000 Agilent 35900E Service Manual 5

Introduction

Manual Overview

Released: MAY 2000 Agilent 35900E Service Manual 6

Introduction

The Agilent 35900E Dual Channel Interface Service Manual provides step-by-

step instructions for removing and replacing various parts in your 35 00E Dual

Channel Interface. Refer to Chapter 3: Parts Replacement for parts

identification.

For operating directions, see the Agilent 35900E Dual Channel Interface

Users Manual.

Caution The 35 00E contains parts that are sensitive to electrostatic discharge. Wear an

ESD wrist strap during all assembly and disassembly procedures.

Manual Overview

This manual contains four chapters.

Chapter 1: Introduction, provides the purposes of this manual and an

overview of its contents.

Chapter 2: Troubleshooting the 35900E, provides a troubleshooting

checklist, an explanation of the LEDs, and a recommendation for use of DEMO

chromatograms.

Chapter 3: Parts Replacement, provides a description of how to remove

each part from the 35 00E Dual Channel Interface.

Chapter : Instrument Parts Breakdown, provides part numbers and

illustrations of each part in the 35 00E Dual Channel Interface.

Released: MAY 2000 Agilent 35900E Service Manual 7

Troubleshooting the 35900E

Trou leshooting the 35900E

Verify the 35900E is Ready for Operation

Released: MAY 2000 Agilent 35900E Service Manual 8

Troubleshooting the 35900E

Verify the 35900E is Ready for Operation

At power up, the 35 00E automatically executes internal self-tests to determine

the amount of memory installed and to verify that the main power, system

memory, and the MIO communication interface, and other internal circuits are

operating properly. These tests take about 30 seconds for a 1-MByte system.

The FAULT light will blink ON/OFF during this time.

When the 35 00E has completed the internal self-tests, verify that:

1. the FAULT lamp is OFF

2. the POWER indicator is ON

3. no other indicators are blinking

In Case of Difficulty

If the 35 00E does not power up correctly, turn power off and check the

following:

1. Rear panel configuration switches 3 through 6 are DOWN (for normal

operation).

2. MIO card is correctly configured for host computer communications.

3. MIO card is connected to host computer or network.

4. Analog signal cables are connected.

5. Remote control cables are connected (if needed).

6. Digital I/O cables are connected (if needed).

7. Power cord is connected.

Trou leshooting the 35900E

Verify the Syste is Ready for Operation

Released: MAY 2000 Agilent 35900E Service Manual 9

If the problem persists after cycling the power, note the LED pattern on the

front panel display. Check the following table for possible causes for failure.

Table 1. Possible Causes for Failure

Verify the Syste is Ready for Operation

Once you have verified that the 35 00E is ready for operation, you can use the

test chromatogram stored in the 35 00E ROM in conjunction with the Host

computer software to check the operation of the entire system. The test

chromatogram is turned on via configuration switches 3 through 6 on the

35 00E’s back panel.

Condition Possible Causes

POWER light is OFF Power cord is disconnected or pro lem with the

power supply

FAULT light remains ON and COMM light is

flashing (note: other lights may also e flashing)

MIO card may e loose or there may e a

pro lem with the MIO card

FAULT light remains ON and Channel B NOT

READY light is ON

No SIMM module in the front slot or there may

e a pro lem with the SIMM module installed

FAULT light remains ON and Channel B RUN light

is ON

Pro lem found with SIMM module installed in the

rear slot

Released: MAY 2000 Agilent 35900E Service Manual 10

Parts Replace ent

Otros manuales para Agilent 35900E

Tabla de contenidos

Otros manuales de Controladores de Agilent Technologies

Agilent Technologies

Agilent Technologies PCG-750 Manual de usuario

Agilent Technologies

Agilent Technologies 929-0022 Manual de usuario

Agilent Technologies

Agilent Technologies Turbo -V 1001 Manual de usuario

Agilent Technologies

Agilent Technologies Turbo-V 1000HT Manual de usuario

Agilent Technologies

Agilent Technologies 8169A Manual de usuario

Agilent Technologies

Agilent Technologies 4UHV Manual de usuario

Agilent Technologies

Agilent Technologies 969-9871 Manual de usuario

Agilent Technologies

Agilent Technologies 929-0196 Manual de usuario

Agilent Technologies

Agilent Technologies Turbo-V 750/850-AG Manual de usuario

Agilent Technologies

Agilent Technologies AGC-100 Manual de usuario

Agilent Technologies

Agilent Technologies 11896A Manual

Agilent Technologies

Agilent Technologies Turbo-V 550 Manual de usuario

Agilent Technologies

Agilent Technologies Turbo-V 81-AG Manual de usuario

Agilent Technologies

Agilent Technologies Eyesys Mini-B/A Manual de usuario

Agilent Technologies

Agilent Technologies X3501-64003 Manual de usuario

Agilent Technologies

Agilent Technologies TwisTorr 74 FS Manual de usuario

Agilent Technologies

Agilent Technologies RS-232 Manual de usuario

Agilent Technologies

Agilent Technologies AIC 5000 Manual de usuario

Agilent Technologies

Agilent Technologies G2743A Manual de instrucciones

Agilent Technologies

Agilent Technologies TwisTorr 84 FS PCB Manual de usuario

Agilent Technologies

Agilent Technologies W2642A Manual de usuario

Agilent Technologies

Agilent Technologies TwisTorr Medium-TMP Rack Manual de usuario

Agilent Technologies

Agilent Technologies Turbo-V 2000HT Manual de usuario

Agilent Technologies

Agilent Technologies TwisTorr 74 FS PCB 24 Manual de usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario