AEMC instruments SR601 Manual de usuario
AC Current Probe
Models SR601 and SR604
User Manual
DESCRIPTION: The SR601/SR604 (Cat. #2113.43/2113.44) are designed for use in industrial environments.
The ergonomic design allows them to easily attach to cables or small bus bars. The “circular” jaws guarantee
a very good accuracy and low phase shift. The probes have a measurement range up to 1000Arms
continuous and are compatible with any AC ammeter, multimeter, or other current measurement instrument
with an input impedance lower than 5Ω. To achieve the stated accuracy, use the SR601/SR604 with an
ammeter having an accuracy of 0.75% or better.
WARNING
The safety warnings are provided to ensure the safety of personnel and proper operation of the
instrument. Read the instruction completely.
• Use caution on any circuit: potentially high voltages and currents may be present and may pose a
shock hazard.
• Do not use the probe if damaged. Always connect the current probe to the measuring device before it
is connected around the conductor
• Do not use on non-insulated conductor with a potential to ground greater than 600V CAT III pollution
2. Use extreme caution when clamping around bare conductors or bus bars.
• Before each use, inspect the probe; look for cracks in housing or output cable insulation.
• Do not use clamp in wet environment or in locations that hazardous gases exist.
• Do not use the probe anywhere beyond the tactile barrier.
INTERNATIONAL ELECTRICAL SYMBOLS
This symbol signifies that the current probe is protected by double or reinforced insulation. Use only
factory specified replacement parts when servicing the instrument.
This symbol signifies CAUTION! and requests that the user refer to the user manual before using
the instrument.
This is a type A current sensor. This symbol signifies that application around and removal from
HAZARDOUS LIVE conductors is permitted.
DEFINITION OF MEASUREMENT CATEGORIES
CAT II: For measurements performed on circuits directly connected to the electrical distribution system.
Examples are measurements on household appliances or portable tools.
CAT III: For measurements performed in the building installation at the distribution level such as on
hardwired equipment in fixed installation and circuit breakers.
CAT IV: For measurements performed at the primary electrical supply (<1000V) such as on primary
overcurrent protection devices, ripple control units, or meters.
RECEIVING YOUR SHIPMENT
Upon receiving your shipment, make sure that the contents are consistent with the packing list. Notify your
distributor of any missing items. If the equipment appears to be damaged, file a claim immediately with the
carrier and notify your distributor at once, giving a detailed description of any damage.
ELECTRICAL SPECIFICATIONS
Current Range:
0.1 to 1000A AC, continuous cycle @ ≤1kHz
Transformation Ratio: 1000:1
Output Signal:
1mA AC/A AC (1A AC at 1000A)
Accuracy and Phase Shift*:
Primary current
0.1 to 10A
10A
50A
Accuracy %
≤3% + 0.1A
3%
1.5%
Phase shift
N/A
3°
1.5°
Primary current
200A
1000A
1200A
Accuracy %
.75%
0.5%
0.5%
Phase shift
0.75°
0.5°
0.5°
(*Reference conditions: 23°C±3°K, 20 to 75% RH, 48 to
65 Hz, external magnetic field <40 A/m, no DC
component, no external current carrying conductor, test
sample centered.) Load impedance 5Ω.
Overload: 1200 A for 40mn on, 20mn off
Accuracy: Per IEC 185
Frequency Range: 30Hz to 5kHz; current derating
above 1 kHz using the formula:
SR601 SR604
Load Impedance: 5Ωmax
Working Voltage: 600V CAT III
Common Mode Voltage: 600V CAT III
Open Secondary Voltage:
< 25V by limiting circuit
Influence of Adjacent Conductor:
< 1mA/A AC
Influence of Conductor in Jaw Opening:
0.1% of reading
Influence of Frequency:
From 30 to 48Hz : < 1% of R
From 65 to 1000Hz : < 0.5% of R
From 1kHz to 5kHz : < 1% of R
MECHANICAL
SPECIFICATIONS
Operating Temperature:
14° to 122°F (-10° to 50°C)
Storage Temperature:
-4° to 158°F (-20° to 70°C)
Influence of Temperature:
< 0.1% per 10°K
Influence of Humidity:
From 10 to 90% : 0.1%
Jaw Opening:
2.25" (57mm) max.
Maximum Conductor Size:
2.05” (52mm)
Envelope Protection:
IP 40 (IEC 529)
Drop Test:
1m (IEC 68-2-32)
Mechanical Shock:
100g (IEC 68-2-27)
Vibration:
5 to 15Hz, 0.15mm (IEC 68-2-6)
15 to 25Hz, 1mm
25 to 55Hz, 0.25mm
Polycarbonate Material:
Handles: ABS Grey and
Lexan 500R, Red: UL94V0
Jaws: Lexan 500R, Red: UL94V0
Dimensions:
4.37 x 8.50 x 1.77" (111 x 216 x 45mm)
Weight:
1.21lbs. (550g)
Output:
SR601: Two standard safety banana
jacks (4mm)
SR604: 5ft. (1.5m) lead with safety
4mm banana plug
SAFETY SPECIFICATIONS
Electrical:
Double insulation or reinforced insulation between
the primary or secondary and the outer case of the
handle conforms to IEC 1010-2-032.
Common Mode Voltage:
600V Category III, Pollution Degree 2
Dielectric Strength:
5550V, 50/60Hz between primary, secondary
and the outer case of the handle
Electromagnetic Compatibility:
EN 50081-1 Class B
EN 50082-2 Electrostatic discharge
IEC 1000-4-2
Radiated field IEC 1000-4-3
Fast transients IEC 1000-4-4
Magnetic field at 50/60Hz IEC 1000-4-8
ORDERING INFORMATION
AC Current Probe SR601................Cat #2113.43
AC Current Probe SR604................Cat #2113.44
Accessories:
Lead, set of 2, 5ft Safety Leads
(1000V CAT IV) ..................................Cat#2152.24
Adapter BNC (Male) –Bannana (Female) (XM-BB)
(600V CAT III).....................................Cat#2118.46
Banana plug adapter
(to non-recessed plug) .....................Cat #1017.45
99-MAN 100132.v13 03/17
OPERATION
Please make sure that you have already read and fully understand the WARNING section on page 1.
Making Measurements with the AC Current Probe Models SR601/SR604
•Connect the black lead of the current probe to “common” and the red lead to the AC current input on
your DMM or other current measuring instrument. Select the appropriate current range (2A AC range).
Clamp the probe around the conductor to be tested with the arrow pointed toward the load. If the reading
is less than 200mA, select the lower range until you obtain the best resolution. Read the value display on
the DMM and multiply it by the probe ratio (1000/1). (If reading = 0.659A, the current flowing through the
probe is 0.659A x 1000 = 659A AC)
•For best accuracy, avoid if possible, the proximity of other conductors which may create noise.
Tips for Making Precise Measurements
•When using a current probe with a meter, it is important to select the range that provides the best
resolution. Failure to do this may result in measurement errors.
•Make sure that probe jaw mating surfaces are free of dust and contamination. Contaminants cause air
gaps between the jaws, increasing the phase shift between primary and secondary. It is very critical for
power measurement.
MAINTENANCE
Warning:
•For maintenance use only original replacement parts.
•To avoid electrical shock, do not attempt to perform any servicing unless you are qualified to do so.
•To avoid electrical shock and/or damage to the instrument, do not get water or other foreign agents into
the probe
Cleaning:
To ensure optimum performance, it is important to keep the probe jaw mating surfaces clean at all times.
Failure to do so may result in error in readings. To clean the probe jaws, use very fine sand paper (fine 600)
to avoid scratching the jaw, then gently clean with a soft oiled cloth.
REPAIR AND CALIBRATION
You must contact our Service Center for a Customer Service Authorization number (CSA#). This will ensure
that when your instrument arrives, it will be tracked and processed promptly. Please write the CSA# on the
outside of the shipping container.
Chauvin Arnoux®, Inc. d.b.a. AEMC®Instruments
15 Faraday Drive •Dover, NH 03820 USA
(800) 945-2362 (Ext. 360) • (603) 749-6434 (Ext. 360) • repair@aemc.com
(Or contact your authorized distributor)
NOTE: All customers must obtain a CSA# before returning any instrument.
TECHNICAL AND SALES ASSISTANCE
If you are experiencing any technical problems, or require any assistance with the proper use or application
of this instrument, please contact our technical hotline:
(800) 343-1391 • (508) 698-2115 • techsupport@aemc.com
LIMITED WARRANTY
The current probe is warranted to the owner for a period of two years
from the date of original purchase against defects in manufacture. This limited warranty is given by AEMC®
Instruments, not by the distributor from whom it was purchased. This warranty is void if the unit has been
tampered with, abused or if the defect is related to service not performed by AEMC®Instruments.
Full warranty coverage and product registration is available on our website at: www.aemc.com/warranty.html
Please print the online Warranty Coverage Information for your records.
Este manual sirve para los siguientes modelos
1
Otros manuales de Instrumento de medición de AEMC instruments
AEMC instruments
AEMC instruments 6505 Manual de usuario
AEMC instruments
AEMC instruments MA194-24-BK Manual de usuario
AEMC instruments
AEMC instruments 300-24-2-10 Manual de usuario
AEMC instruments
AEMC instruments MR525 Manual de usuario
AEMC instruments
AEMC instruments OX5042 Manual de usuario
AEMC instruments
AEMC instruments CM605 Manual de usuario
AEMC instruments
AEMC instruments 6505 Manual de usuario
AEMC instruments
AEMC instruments MN185 Manual de usuario
AEMC instruments
AEMC instruments MR525 Manual de usuario
AEMC instruments
AEMC instruments CA811 Manual de usuario
AEMC instruments
AEMC instruments K100 Manual de usuario
AEMC instruments
AEMC instruments Digital FlexProbes 400D-10 Manual de usuario
AEMC instruments
AEMC instruments A196-24-BK Manual de usuario
AEMC instruments
AEMC instruments MN185 Manual de usuario
AEMC instruments
AEMC instruments PEL 105 Manual de usuario
AEMC instruments
AEMC instruments CA846 Manual de usuario
AEMC instruments
AEMC instruments AmpFlex 193-24-BK Manual de usuario
AEMC instruments
AEMC instruments JM835A Manual de usuario
AEMC instruments
AEMC instruments 6527 Manual de usuario
AEMC instruments
AEMC instruments 407 Manual de usuario
Manuales populares de Instrumento de medición de otras marcas
Endress+Hauser
Endress+Hauser Proline Promag 50 Especificaciones técnicas
Siemens
Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas
KLINGER
KLINGER CMF V Series Manual de usuario
EXFO
EXFO FTB-2 Manual de operación y mantenimiento
Keysight
Keysight M8290A Manual de usuario
ADTEK
ADTEK MW-5 Manual de usuario