Advantech ICR-4453W Guía

Start Guide

ICR-4401, ICR-4434, ICR-4453

LUCOM GmbH — Flößaustr. 22a — 90763 Fürth — Tel.: +49 911/ 957 606 00 — E-Mail: [email protected] — www.lucom.de

www.lucom.de

Start Guide

Safety Instructions

Please take care to following instructions:

•Use the router in compliance with national and international law and in compliance with

any special or additional restrictions regulating the use of the router in various applica-

tions and environments.

•To avoid possible injury and/or damage to the device, observe the relevant provisions

and standards. Use only the original accessories as recommended. Unauthorized de-

vice or accessory modiﬁcation or using accessories that have not been approved can

result in router damage and/or violation of the regulations.

•Unauthorized device or accessory modiﬁcation or using the accessories that have not

been approved can result in warranty termination.

•Do not open the router.

•Caution! This equipment is not suitable for use in locations where children are likely to

be present. The SIM card could be swallowed by small children.

•When connecting the device to a power supply, do not exceed the deﬁned voltage.

•Do not expose the router to extreme ambient conditions. Protect the router against dust,

moisture, and high temperature.

•It is recommended that you do not use the router at petrol ﬁlling stations. We recommend

observing local restrictions concerning radio-based devices while working with explosive

material, such as at petrol ﬁlling stations or in chemical plants.

•While using the router close to personal medical devices, such as cardiac pacemakers

or hearing aids, proceed with heightened caution.

•Operating the router too close to TV sets, radio receivers, personal computers, or tele-

phones can cause interference.

•It is recommended that you create a copy or backup of the essential settings stored in

the memory of the router.

QSG-0010-EN, November 8, 2021 1Released in the Czech Republic

LUCOM GmbH — Flößaustr. 22a — 90763 Fürth — Tel.: +49 911/ 957 606 00 — E-Mail: [email protected] — www.lucom.de

www.lucom.de

Start Guide

Product Disposal Instructions

The WEEE (Waste Electrical and Electronic Equipment: 2012/19/EU) di-

rective was introduced to ensure that electrical/electronic products are recycled

using the best available recovery techniques to minimize the impact on the en-

vironment. This product contains high-quality materials and components which

can be recycled. At the end of its life, this product MUST NOT be mixed with

other commercial waste for disposal. The device contains a battery. Remove

the battery from the device before disposal. The battery in the device needs to be disposed of

apart accordingly. Check the terms and conditions of your supplier for disposal information.

Open Source Software License

The software in this device uses various pieces of open-source software governed by the

following licenses:

•GPL versions 2 and 3

•LGPL version 2

•BSD-style licences

•MIT-style licences

The list of components together with complete license texts can be found on the device

itself. See the Licenses link at the bottom of the router’s main Web page (General Status)

or point your browser to this address (replace the DEVICE_IP string with the real router’s IP

address):

https://DEVICE_IP/licenses.cgi

This is a written offer valid for three years since the device purchase, offering any third party

for a charge no more than the cost of physically performing source distribution, a complete

machine-readable copy of the corresponding source code on a ﬂash drive medium. If you are

interested in obtaining the source, please get in touch with us at:

[email protected]

Modiﬁcations and debugging of LGPL-linked executables:

The device manufacturer hereby grants the right to use debugging techniques (e.g., de-

compilation) and making customer modiﬁcations of any executable linked with an LGPL library

for its purposes. Note these rights are limited to the customer’s usage. No further distribution

of such modiﬁed executables and no transmission of the information obtained during these

actions may be done.

QSG-0010-EN, November 8, 2021 2Released in the Czech Republic

LUCOM GmbH — Flößaustr. 22a — 90763 Fürth — Tel.: +49 911/ 957 606 00 — E-Mail: [email protected] — www.lucom.de

www.lucom.de

Start Guide

First Use

Before applying power to the router, connect all the components that you need for your

applications. A cross-shaped screwdriver is necessary to insert a SIM card or a microSD card.

Do not run the router without antennas connected to the main antenna connectors as the

energy from the transmission is effectively reﬂected by the open end and can damage

the equipment.

ICR-4401 routers are not equipped with a cellular module, which means that the SIM

card slots together with the cellular and GNSS antenna connectors are not available on

the router.

1. Antenna

Use SMA connectors to connect the antennas to the router; see the ﬁgure below. It is highly

recommended to connect all the antennas.

QSG-0010-EN, November 8, 2021 3Released in the Czech Republic

LUCOM GmbH — Flößaustr. 22a — 90763 Fürth — Tel.: +49 911/ 957 606 00 — E-Mail: [email protected] — www.lucom.de

www.lucom.de

Start Guide

2. SIM Card

The SIM card reader for two mini-SIM cards (2FF with size of 25.0 x 15.0 x 0.76 mm)

is located on the router’s rear panel under a metal cover. If you intend to use this device to

communicate over a cellular network, please place an activated data-provisioned SIM card

into the SIM card reader. Unscrew the cover and push your SIM card into the SIM1 or SIM2

slot until it clicks into place. You can install two SIM cards simultaneously to utilize the SIM

card switching feature.

Disconnect the router from the power supply before handling the SIM card.

QSG-0010-EN, November 8, 2021 4Released in the Czech Republic

LUCOM GmbH — Flößaustr. 22a — 90763 Fürth — Tel.: +49 911/ 957 606 00 — E-Mail: [email protected] — www.lucom.de

www.lucom.de

Start Guide

3. Power

The router requires an external DC power supply. The DC voltage required is between

+9 and +48 V DC. The router has built-in protection against reverse polarity without signaling.

Connect the power supply cable to the PWR connector on the router’s front panel; see the

ﬁgure below.

The power voltage for the PoE router version must be 48 V DC to work as the PoE PSE

device.

4. Ethernet

For an initial conﬁguration, made in a web browser, connect a PC by an Ethernet cable to

the default LAN interface, use one of the ETH0 ports, see the ﬁgure above. By default, this

interface has the following conﬁguration:

Connectors Purpose Default Setting

ETH0 LAN ports (default)

Connect your PC to one of these ports to

get the router web interface.

DHCP Server enabled

IP Address: 192.168.1.1

NetMask: 255.255.255.0

QSG-0010-EN, November 8, 2021 5Released in the Czech Republic

LUCOM GmbH — Flößaustr. 22a — 90763 Fürth — Tel.: +49 911/ 957 606 00 — E-Mail: [email protected] — www.lucom.de

www.lucom.de

Start Guide

Conﬁguration

1. Conﬁguring the Device Using the Web Browser

You can use a web browser running on your PC to get access to the router web interface.

Here you can perform router monitoring, conﬁguration, and administration. First, connect

the PC to the default LAN interface as described in the Ethernet chapter. To get the router

interface, enter the https://192.168.1.1 address in a web browser. Please note that usage

of the HTTPS protocol for secure communication over the network is required.

By default, there is just the root user account created on the router. See the product label

on the router for its default password. Log in to the web interface by the root user and his

password. See the conﬁguration manual of the router for a detailed description and examples

of the router conﬁguration.

After logging on to the device for the ﬁrst time, we strongly recommend changing the

default password due to security reasons.

For security reasons, it is highly recommended to update the ﬁrmware of the router to the

latest version regularly. Downgrading the ﬁrmware to an older version than the production

version or uploading a ﬁrmware intended for a different device may cause the malfunction

of the device.

2. Conﬁguration Settings via WebAccess/DMP

Your router has been pre-installed with the WebAccess/DMP client. For its activation,

enable it in the router’s web interface (Customization -> User Modules -> WebAccess/DMP

Client). For more information see the conﬁguration manual of your router.

The activated client periodically uploads router identiﬁcators, its conﬁguration, and cellu-

lar network statistics to the WebAccess/DMP server.

With the WebAccess/DMP client activated, you may conﬁgure the router from WebAc-

cess/DMP portal. Navigate your browser to https://www.wadmp.com.

If this is your ﬁrst time, please self-sign-up with the site. If not, please log in with your

username and password. Once logged in, further assistance can be found at https://docs.

wadmp.com.

QSG-0010-EN, November 8, 2021 6Released in the Czech Republic

LUCOM GmbH — Flößaustr. 22a — 90763 Fürth — Tel.: +49 911/ 957 606 00 — E-Mail: [email protected] — www.lucom.de

www.lucom.de

Start Guide

3. Restoring and Backing up the Router Conﬁguration

If you reset the router, the current conﬁguration replaces by the default factory settings.

Therefore, we recommend you back up the router conﬁguration before resetting the device.

Refer to the conﬁguration manual for more information.

You can restore the default router conﬁguration once the router boots up and the PWR

LED starts blinking. To do so, press the RST button on the router’s front panel for more than

4 seconds. After you press this button, all settings reset to the default values, and the router

will reboot.

Support

All product-related manuals, documents, and software can be found and downloaded on

the website at icr.advantech.cz/download address.

Hereby we, Advantech Czech s.r.o., declare that the radio equipment type ICR-4401

(WiFi version), ICR-4434, and ICR-4453 comply with Directive 2014/53/EU.ICR-4401

(non-WiFi version) complies with Directives 2014/30/EU and 2014/35/EU.

The full text of the EU Declaration of Conformity is available at the following internet address:

icr.advantech.cz/eudoc

QSG-0010-EN, November 8, 2021 7Released in the Czech Republic

LUCOM GmbH — Flößaustr. 22a — 90763 Fürth — Tel.: +49 911/ 957 606 00 — E-Mail: [email protected] — www.lucom.de

www.lucom.de

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Enrutador de red de Advantech

Advantech

Advantech IMC-150LI Manual de instalación y operación

Advantech

Advantech SmartMotion ST352 Manual de usuario

Advantech

Advantech ADAM-6520 Series Manual de usuario

Advantech

Advantech ICR-1601 Manual de usuario

Advantech

Advantech LR77 v2 Series Manual de usuario

Advantech

Advantech UR5i v2 Libratum Manual de usuario

Advantech

Advantech B+B SmartWorx LR77 v2 Hoja de instrucciones

Advantech

Advantech ICR-2701 Manual de usuario

Advantech

Advantech SmartStart SL306 Manual de usuario

Advantech

Advantech ICR-2441 Manual de usuario

Advantech

Advantech B+B Smartworx SEC510-2SFP-T Manual de usuario

Advantech

Advantech B+B SmartWorx SmartStart Guía

Advantech

Advantech ICR-3831 Guía

Advantech

Advantech B+B SmartWorx ER75i v2 Manual de usuario

Advantech

Advantech EKI-2726FHPI Series Manual de instalación y operación

Advantech

Advantech ICR-4401 Manual de usuario

Advantech

Advantech ICR-4401 Manual de usuario

Advantech

Advantech ICR-2431 Manual de usuario

Advantech

Advantech B+B SmartWorx AirborneM2M BB-ABDN-ER-DP553 Manual de usuario

Advantech

Advantech Libratum ICR-2834 Guía

Advantech

Advantech ICR-2041 Manual de usuario

Advantech

Advantech ICR-2000 Guía

Advantech

Advantech ICR-3241 Manual de usuario

Advantech

Advantech SmartMotion ST352 Manual de usuario

Manuales populares de Enrutador de red de otras marcas

Allnet

Allnet ALL0333AU Manual de usuario

HomeSeer

HomeSeer HT-SEL Manual de usuario

Sercomm

Sercomm Genesis OC3505D Manual de usuario

Billion

Billion BIPAC 5102 Series Manual de usuario

TP-Link

TP-Link TD-8817 Manual de usuario

Motorola

Motorola MR1900 Manual de usuario

Digi

Digi IX14 Manual de usuario

Cisco

Cisco NCS 540 Manual

XAVi

XAVi X8821e Manual de usuario

BEC

BEC 6200WZL Manual de usuario

MikroTik

MikroTik hAP ac3 Series Manual de usuario

Korenix

Korenix JetNet 5428G Series Manual de usuario

NETGEAR

NETGEAR FS526T - Switch Manual de usuario

Korenix

Korenix JetNet 5710G Series Manual de usuario

Automated Logic

Automated Logic ZN551 Manual del propietario

Cisco

Cisco ASR 1000 Series Manual del operador

EnGenius

EnGenius ESR-9710 Manual de usuario

Cisco

Cisco 805 Series Instrucciones de funcionamiento y seguridad