Advantech MIC-1816R Manual de instalación y operación
MIC-1816R Startup Manual 1
Before installation, please ensure that the following items
have been included in your shipment:
1. 1 x MIC-1816R system
2. 1 x Adapter 100 ~ 240 V 36 W 12 V without PFC
DC plug 90°
3. 1 x MIC-1816R startup manual
4. 1 x User note for MIC-1816R
If any of these items are missing or damaged, please con-
tact your distributor or sales representative immediately.
Caution:
BATTERIES ARE AT RISK OF EXPLODING IF
INCORRECTLY REPLACED. REPLACE ONLY WITH
THE SAME OR EQUIVALENT TYPE RECOMMEND-
ED BY THE MANUFACTURER. DISCARD USED
BATTERIES ACCORDING TO THE MANUFAC-
TURER’S INSTRUCTIONS.
Attention:
DANGER D’EXPLOSION SI LA BATTERIE EST
INEXACTEMENT REMPLACÉE. REMPLACEZ
SEULEMENT AVEC LA MÊME CHOSE OU LE TYPE
ÉQUIVALENT RECOMMANDÉ PAR LE FABRICANT,
JETTENT LES BATTERIES UTILISÉES INSTRUC-
TIONS DE S SELON FABRICANT DES’.
MIC-1816R
16-Bit, 1 MS/s DAQ Platform with NXP ARM®
Cortex®-A9 i.MX6 1 GHz Processor
Startup Manual
System
• NXP ARM®Cortex®-A9 i.MX6 high-performance processor
Memory
• 4 GB DDR3 memory and eMMC onboard
Graphics
• HDMI 1920 x 1080 @ 60 Hz
Serial Ports
• 2 x RS-232 from COM1/COM2
• 2xCANfromCAN1/CAN2
Ethernet
• Interface: 10/100/1000 Mbps
• Controller: NXP i.MX6-integrated RGMII
Storage
• Internal SSD: 1 x 2.5” SSD bay
Front I/O
• USB: 1 x USB 2.0 and 1 x USB 2.0 OTG
Power Requirement
• Power Type: DC power jack
• Input Voltage: 12 VDC
Miscellaneous
• Power Switch
Orange: System standby
Green: System boot
Mount Kit (Optional)
• Table Mount: 1960077844N001; 130 x 175 mm
• DIN Rail Mount: 1960018849T001
Environment
• Operating Temperature:
-10 ~ 60 °C/14 ~ 140 °F with
0.7m/S air flow and 1 x industrial SSD
• Relative Humidity: 95% @ 40 °C (non-condensing)
Physical Characteristics
• Dimensions (W x H x D): 165 x 130 x 66 mm (6.49 x
5.11 x 2.59 in)
• Weight: 1.05 kg (2.32 lb)
Specications Packing List
For more information about this or other Advantech
products, please visit our website at
http://www.advantech.com
http://www.advantech.com/Products
For technical support and customer service, please
visit our support website at
http://support.advantech.com.tw/support/default.
aspx
This manual is for the MIC-1816R Series.
Part No. 2041181600
Printed in Taiwan
Edition 1
April 2019
2 MIC-1816R Startup Manual
AI – Current Mode (channel shared with voltage mode)
Channels 8 single ended
Resolution 16 bit
Built-In
Memory 4K samples
Sampling Rate
(shared with
current mode)
Single Channel 5 MS/s
Multi Channel 1 MS/s
Unipolar/Bipolar
Mixed 250 KS/s
Input Range 4~20 mA (according to a 0 ~ 10 V voltage range)
Drift
Zero 35 ppm/°C
Span 25 ppm/°C
Input Signal
Bandwidth
(-3dB)
15 Hz
Max. Input
Current 21 mA
Input
Impedance 500 Ω/220 uF
Clock Source Software or external
Trigger Mode Start trigger, delay start trigger
Stop trigger, delay stop trigger
Accuracy DC
INLE: ± 2 LSB
DNLE: ± 1 LSB
Offset Error: ± 1 LSB (under manual adjustment)
Gain Error: 0.02% FSR
IEPE Signal Conditioner
Channels 4 single ended
IEPE Current 4 mA ±5%
Gain 1/10/100 (for AC signal)
Couple AC
Input Voltage 4 ~ 24 V (normal operation)
Amplier
Output Voltage 4 ~ 24 V (normal operation)
Accuracy ±2%
Compliance 24 V
Upper Cut-Off
Frequency
x 1, x 10 gain (-5%): 100K Hz
x 100 gain (-15%): 50K Hz
Lower Cut-Off
Frequency 1.77 Hz (-5%, load: 1M Ω, for all gain settings)
Discharge
Time Constant >0.3 seconds
DC Offset <±30 mV
Sensor
Status
Indicator
IEPE Sensor Normal Short
LED Green Red
Software
(DI port 0)
Bit 0, 2, 4, 6 =
”High”
Bit 1, 3, 5, 7 =
”High”
The MIC-1816R system features a built-in data acquisition
module.
Analog Input
AI – Voltage Mode (channel shared with current mode)
Channels 8 single ended/4 differential
Resolution 16 bit
Built-In
Memory 4K samples
Sampling Rate
(shared with
current mode)
Single Channel 5 MS/s
Multi Channel 1 MS/s
Unipolar/Bipolar
Mixed 250 KS/s
Input Range
and Gain List
Gain 0.5 1 2 4 8
Unipolar NA 0 ~ 10 0 ~ 5 0 ~
2.5
0 ~
1.25
Bipolar ±10 ±5 ±2.5 ±1.25 ±0.625
Drift
Gain 0.5 1 2 4 8
Zero 25 ppm/°C
Span 15 ppm/°C
Input Signal
Bandwidth
(-3dB)
Gain 0.5 1 2 4 8
BW (MHz) 4.4 4.4 4.4 3.3 1.7
Max. Input
Voltage ± 15 V
Input
Impedance 1G Ω/2 pF
Clock Source Software or external
Trigger Mode Start trigger, delay start trigger
Stop trigger, delay stop trigger
Accuracy
DC
INLE: ± 2 LSB
DNLE: ± 1 LSB
Offset Error: ± 1 LSB (under manual adjustment)
Gain 0.5 1 2 4 8
Gain Error
(%FSR) 0.0075 0.0075 0.0075 0.008 0.008
Channel
Type Single ended/differential
AC
SNR: 81 dB
ENOB: 13 bit
External
Analog Trigger
RRange: -10 ~ 10 V
Resolution: 16 bit (0.3 mV/step)
Bipolar Range Unipolar Range ±1 LSB for Full-Scale Step
±10 V NA 1.04 us
±5 V 0 ~ 10 V 1.04 us
±2.5 V 0 ~ 5 V 1.04 us
±1.25 V 0 ~ 2.5 V 4 us
±0.625 V 0 ~ 1.25 V 5 us
DAQ Specications
MIC-1816R Startup Manual 3
DAQ Specications (Cont.)
Analog Output
AO – Voltage Mode (channel shared with current mode)
Channels 2
Resolution 16 bit
Memory Size 4K samples
Update Rate 3 MS/s
Output Range 0 ~ 5 V, 0 ~ 10 V, -5 ~ 5 V , -10 ~ 10 V
Accuracy
Relative ±1 LSB
Differential
Non-Linearity ±1 LSB (monotonic)
Slew Rate 20 V/us
Gain Error Adjustable to zero (with manual calibration)
Drift 30 ppm/°C
Driving Capability
5 mA
Update Mode Static update, waveform
Output Impedance
Max. 0.1 Ω
Capacitive Load Max. 500 pF
AO – Current mode (channel share with voltage mode)
Channels 2
Resolution 16 bit
Memory Size 4K samples
Update Rate 20 KS/s
Output Type Source/sink
Output Range 4 ~ 20 mA (according to a 0 ~ 10 V voltage
range)
Gain Error Source: 0.15% FSR
Sink: 0.05% FSR
Drift 40 ppm/°C
Update Mode Static update, waveform
External Loading
Source: 600 Ω
Sink: depends on external voltage
(RL = 50 (VDC - 11) )
Excitation
Voltage
Source: N/A
Sink: Max. 50 VDC
Isolated Digital I/O
Isolated Digital Input
Channels 8
Input Voltage Logic 0: 2 V max.
Logic 1: 5 ~ 50 V
Isolation Protection 2,500 VDC
Overvoltage
Protection 70 VDC
ESD Protection 2,000 VDC
Opto-Isolator
Response 100 µs
Isolated Digital Output
Channels 8
Output Type Sink (NPN)
Isolation Protection 2,500 VDC
Output Voltage 5 ~ 40 VDC
Sink Current 500 mA max./channel
Opto-Isolator
Response 100 µs
Counter
Counter Chip N/A
Channels 2 channels (independent)
Resolution 32 bit
Compatibility TTL level
Base Clock Internal clock at 20 MHz or external clock (10
MHz max.)
Output Frequency Max. 10 MHz
Opto-Isolator
Response 1 us
Clock Input
Low 0.8 V max.
High 2.0 V min.
Gate Input
Low 0.8 V max.
High 2.0 V min.
Counter Output
Low 0.8 V max. @+15 mA
High 2.0 V min. @-15 mA
Error in
Advanced
Functions
Frequency
Measurement
0.1% when the input signal
frequency is ≥ 40 KHz
Pulse Width
Measurement
0.1% when the input signal
frequency is ≤ 40 KHz
Pulse Output Within 2% when the output
frequency is > 1 MHz
PWM Output Within 2% when the output
frequency is > 1 MHz
4 MIC-1816R Startup Manual
LED Indicator Description
Power 12V
DC
power
HDD Normaloperation
Normal(green) IEPEnormaloperation
Short(red) IEPEsensorshort(<1V)
Gain Setting (IEPE Only)
Gain AI0 AI1 AI2 AI3
1↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓
10 ↓ ↑ ↓ ↑ ↓ ↑ ↓ ↑
100 ↑ ↓ ↑ ↓ ↑ ↓ ↑ ↓
NA ↑ ↑ ↑ ↑ ↑ ↑ ↑ ↑
Analog Input Setting
AI4 AI5 AI6 AI7 AI8 AI9
Voltage ↑ ↑ ↑ ↑ ↑ ↑
Current ↓ ↓ ↓ ↓ ↓ ↓
SSD Installation
1. Unscrew the 4 screws and remove the top cover.
2. Secure the 4 screws affixing the SSD to the top cover.
3. Assemble SATA and power cable. Secure in place
using 4 screws.
Table Mount Installation
MIC-1816R can be fitted with a table mount for easy
operation.
1. Unscrew the 4 screws affixing the rear cover in place.
2. Align the screw holes of the table mount to the screw
holes of the MIC-1816R rear cover. Secure the table
mount to the device using 4 screws.
DIN Rail Mount Installation
MIC-1816R can be fitted with a DIN rail mount for flexible
installation.
1. Align the screw holes of the DIN rail mount to the screw
holes of the MIC-1816R rear cover. Secure the rail
mount to the device using 3 screws.
This device complies with the requirements in Part 15 of
the FCC Rules. Operation is subject to the following two
conditions:
1. The device must not cause harmful interference.
2. The device must accept any interference received,
including interference that may cause undesired
operation.
LED Indicator and Switch Settings
Installation
Procedures
Installation
Procedures (Cont.)
Declaration of Conformity
MIC-1816R Startup Manual 5
Analog Input (AI4 ~ AI11)
Current Connection
SettheAIswitchto“current”modeandtheinputrangeas
0~10Vusingsoftware.
Note:Whenthereadvalueiswithin0~10V,thedatainthe
tablebelowcanbeusedtomapthecurrentvalue.
CurrentInput AI4~AI11
4mA 2V
5mA 2.5V
: :
19mA 9.5V
20mA 10V
Analog Input (AI4 ~ AI11)
Single-Ended Channel Connections
Withthesingle-endedinputconguration,onlyonesignal
wireisusedforeachchannelandthemeasuredvoltage
(Vm)isthevoltageinreferencetothecommonground.
Analog Input (AI4 ~ AI11)
Differential Channel Connections
Thedifferentialinputchannelsoperatewithtwosignal
wiresforeachchannel,andthevoltagedifferencebetween
bothsignalwiresismeasured.WithMIC-1816R,whenall
channelsareconguredtodifferentialinput,upto4analog
channelsareavailable.
MIC-1816Rprovidesbothcurrentoutputandvoltageoutput.
Thecurrentandvoltagemodesareshownbelow.
Analog Output - Current Connection
Thecurrentmoderequiresanoutputrangeof0~10V,
conguredviasoftware.Refertothetablebelowforthe
currentvalue.
Current- Source Wiring
ThemaximumresistanceRLis600Ω
Current- Sink Wiring
ExpressionbetweenRLandVDC
RL=50(VDC-11)Ω
IfVDC=12V,RL=50Ω(max.)
IfVDC=24V,RL=650Ω(max.)
AO0andAO1 CurrentOutput(actual)
0V N/A
: :
1.5V N/A
2V 4mA
2.5V 5mA
: :
9.5V 19mA
10V 20mA
Analog Output - Voltage Connection
Thegurebelowshowshowtocongurethevoltageoutput.
Input Connections
Output Connections
6 MIC-1816R Startup Manual
ToconguretheAItypeorGainsettings,apapercliporSIMejecttoolisrequired.
Analog Input Setting
System Dimensions
System I/O
Tabla de contenidos
Otros manuales de Controladores de Advantech
Advantech
Advantech MIC-3327DC01-A43E Manual de instalación y operación
Advantech
Advantech PCI-1241 Manual de usuario
Advantech
Advantech Celeron M Universal Network Controller with PC/104 Extension... Manual de usuario
Advantech
Advantech UNO-2050 Manual de usuario
Advantech
Advantech ADAM-5510 Series Manual de instalación y operación
Advantech
Advantech SKY-4120B Manual de usuario
Advantech
Advantech LNC-5800D Manual del propietario
Advantech
Advantech ADAMView Manual de usuario
Advantech
Advantech UNO-127 Manual de usuario
Advantech
Advantech PCM-26D2CA Manual de instalación y operación
Advantech
Advantech UNO-2053E Manual de usuario
Advantech
Advantech WISE-5580 Manual de usuario
Advantech
Advantech AMAX-5580 Manual de usuario
Advantech
Advantech Celeron M Universal Network Controller with PC/104 Extension... Manual de usuario
Advantech
Advantech UNO-2160 Manual de usuario
Advantech
Advantech UNO-2182-D13BE Manual de usuario
Advantech
Advantech PCI-1760U Manual de instalación y operación
Advantech
Advantech ADAM-5511 Manual de usuario
Advantech
Advantech UNO-348 Manual de usuario
Advantech
Advantech MIC-3321 Manual de instalación y operación
